Question about 2000 Pontiac Grand Am GT

1 Answer

I was wondering where the drain plug is to flush the coolant out. Also, what is the best method to flush out the radiator? I have a 2000 Grand Am.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

There is a drain plug on the engine compartment side of the radiator at the bottom of the plastic tank. The best way to flush your cooling system is to get a Prestone Raditor Flushing Kit. You can use a garden hose to flush the system out.

Posted on May 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to back flush heater core 2007 grand prix


drain coolant system locate heater cores hoses going through firewall you need to buy the radiator flush kit at any auto parts stores. remove heater cores hoses from one end or buy extra long heater hoses same size as heater core hoses in vechicle at auto parts store use the flush kit when you flush through one of the heater core hoses let the other hose drain in a drain pan when you use home garden hose use low water pressure dont use garden hose to the max or you will rupture heater core. your best bet let radiator shop flush whole coolant system. because heater cores hoses are in a tight spot.make sure engine off if you just going to flush out heater core only .after flushing heater core good time to replace heater core hoses.if job too hard or complicated let radiator shop flush out radiator the engine block and heater core because if radiator stopped up or engine block stopped up the gunk and rust will reenter plug up heater core.if you tight on money you can flush out your own radiator.drain out radiator using large drain pan. remove top radiator hose and remove bottom radiator hoses connect to water pump.use garden hose with flush kit part with water pressure not too high put garden hose to top radiator hose run water until clear water run out bottom radiator hose in drain pan,the flush out engine block remove thermostat.if you had another spare thermostat housing with RTV SILICONE SEALANT THAT HAS SET UP INSTALL THERMOSTAT HOUSING BACK TO ENGINE WITHOUT THERMOSTAT FLUSH OUT THE ENGINE BLOCK, WHEN DONE INSTALL NEW THERMOSTAT THEN INSTALL ORIGINAL THERMOSTAT HOUSING WITH NEW ORING WHICH YOU BUY AT DEALERSHIP.IF ALL SOUND COMPLICATED LET RADIATOR SHOP FLUSH OUT COOLANT SYSTEM.

Nov 27, 2012 | 2003 Pontiac Grand Prix

1 Answer

How do I flush the cooling system in a 2000 hyundai elantra?


There are several methods for flushing the cooling system on ALL engine cooling systems. Time honored is drain the radiator (drain ****). Fill with fresh water and run engine to operating temperature until cooling fans turn on. Drain cooling system again. Refill with 50-50 coolant. Another method is purchasing a "T" vlave (coolant flush/service kit) from Autozone, PepBoys, NAPA, O'Reilys, CarQuest, etc.). This "T" valve is installed in one of the heater hoses & attached to a garden hose. Remove the radiator cap & turn on the water supply to the garden hose. Let water run until flush water is 'clear'. Remove garden hose from T valve & refill radiator with pure coolant until the T valve drainage turns green/orange. Install T valve cap... DONE!

Sep 08, 2011 | 2000 Hyundai Elantra

1 Answer

A diagram of the flushing of a radiator and block of a chevrolet blazer LS 2000


Theres no such thing as a diagram, here are the draining instructions, hope this helps...
  • 1-Place a large drain pan beneath the radiator drain plug. The drain plug is located on the passenger side at the very bottom of the radiator on the engine side.

  • 2-Make sure the engine is cool. Open the hood of the truck and remove the radiator cap.
  • 3-Loosen the drain plug. On the 2000 Blazer, the drain plug is a wing-nut type of plug. Twist it with your fingers until the coolant begins to drain.

  • *To flush the block, once you have drained the radiator, run the engine for a bit untill the temp gauge goes up to normal, then the coolant will have been evacuated from the block. DO NOT leave the engine on, once it reaches normal temp, (this will happen quick) turn off right away, otherwise you'll be forking out a few hundred $$$ to fix the worped heads.
    4-Tighten the drain plug with your fingers once the coolant has drained fully from the radiator. Remove the drain pan and dispose of the used coolant properly.
    Some service stations will take and recycle your used coolant.
    Hope this helps...



  • Read more: How to Drain a Radiator From a 2000 Chevy Blazer ' eHow.com http://www.ehow.com/how_6357264_drain-radiator-2000-chevy-blazer.html#ixzz1VS4RBufX

    Aug 19, 2011 | 2000 Chevrolet Blazer

    1 Answer

    Can you use a prestone flush and fill kit without opening the radiator drain **** or removing hoses?


    No, the flush kit is mounted on the heater hose and you need to drain the system. Removing the lower radiator hose and termostat is the best method for flushing draining the coolant system.

    Nov 11, 2010 | 1996 Ford Taurus

    1 Answer

    Where is the engine coolant drain valve located? and what is the best procedure to change the coolant and flush the radiator? thanks


    1.) the drain valve is a bolt type device under the radiator..

    2.) different flush has different methods usually buy the flush and follow the instructions.. usually
    empty radiator by loosening valve underneath
    tighten back valve when drained
    pour in flush and top up with water
    start car and allow to run for 15 minutes (with cap off)
    cut off
    let cool and then drain..

    add coolant .. your done..

    Oct 29, 2010 | 1996 Oldsmobile Cutlass Supreme Coupe

    2 Answers

    Where is the drain plug for the radiator on a 2000 buick lesabre


    c2d1fde.jpgOk looking at all different Manufactors, and i have'nt seen one with a radiator drain plug..So if you are tring to flush your raditor, just take off the bottom radiator hose, and run a hose in the radiator, and flush it out the best way you can...Then top it off with a Gallon of coolant, and you should be fine...Goodluck...

    Dec 11, 2009 | 2000 Buick LeSabre

    2 Answers

    Is there a radiator drain plug on a 2002Pontiac Grand Prix 3.1 L


    The textbook method is to remove the drain plug on the bottom of the radiator.

    Most drain plug ismake of inexpensive nylon/plastic and it may fall apart while you turn it.

    The professional method is to loosen the lower radiator clamp and drop to lower radiator hose.

    Drain the coolant onto a large drain pan and recycle the coolant

    ===

    I just did a FREE write up on air purge from coolant system and how todetect initial state of blown head gasket at the Fixya tip selection.

    Click HERE

    or follow link below.

    http://www.fixya.com/cars/r3582329-how_to_inspectdiagnose_and_repair_minor_

    Nov 09, 2009 | 2002 Pontiac Grand Prix

    2 Answers

    How do you flush out the radiator?


    You merely start the engine: loosen the radiator drain-valve, radiator-cap, and refill radiator with water as the engine runs(don't allow the engine run to without water in it). Repeat this for as long as thirty minutes or so until only fresh water comes out the drain-hole. Finally, refill radiator with new anti-freeze. You are done! (or buy a radiator-flush from autoparts store and follow direction written on it). (antifreeze are toxic to our environment)

    Nov 06, 2009 | 1999 Ford Taurus

    2 Answers

    How to flush radiator in a 2004 Mitsubishi endeavor


    Drain your existing coolant from the coolant system there should be a drain petcock on your radiator along the bottem. Once the coolant is drained add water and a radiator flush solution, availeable from most auto parts stores, refill your coolant system and run your engine usually 10 minutes or more. Check the instructions on the type of cleaning solution you buy. Afterward drain the coolant system, flush with water by filling and running it again, then drain and service with proper level of coolant. Always remember to let your engine cool between runs to safely remove your radiator cap DO NOT remove the radiator cap if engine is still hot from running.

    Nov 04, 2009 | 2004 Mitsubishi Endeavor

    Not finding what you are looking for?
    2000 Pontiac Grand Am GT Logo

    325 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8825 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...