Question about 2006 Volkswagen GTI

Open Question

Install ignition lock cylinder 2006 vw mkv gti

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

  • 1 Answer

SOURCE: loosing clutch when drive fast threw the gears

try bleedin it again it might not bein workin as responsive as it should be and bleedin it should give it more pressure to do so

Posted on Jul 29, 2009

alicantecoli
  • 22095 Answers

SOURCE: How do I install an ignition lock-2001 VW Jetta

their is a pin that need to be pushed down to remove the barrel but you cannot access this from the outside .the last one i done i measured it up with the new one then drilled a hole where it should be according to the new one .The lock has to be in the aux position to push the pin in once you have worked out where to drill the hole .If i remember rightly i removed the whole steering coloumn to drill the hole with a small drill bit then realised it was out a bit so i drilled it out with a bigger bit ,changed barrel and refilled hole with some filler and painted it silver so couldnt be called a bodger

Posted on Aug 22, 2009

  • 88 Answers

SOURCE: i need a wiring diagram for a 96 vw golf gti vr6

http://www.the12volt.com/installbay/alarmdetail/2180.html

Posted on Apr 06, 2010

  • 1565 Answers

SOURCE: how to change 1999 VW cabrio ignition lock

autozone.com has a free repair guide, see below

printpage_icon.gif


REMOVAL & INSTALLATION

1990-94 Cabriolet,1990-93 Fox, 1990-92 Golf and Jetta


0900c15280267f2b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Lock cylinder drill point.

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel, then remove the steering column covers.
  3. Remove the turn signal and wiper switches.
  4. Disconnect the ignition switch wiring.
  5. On some models, the hole in the lock body for removing the ignition lock cylinder was not drilled by Volkswagen. To make the hole, use the following measurements in conjunction with the illustrations. Drill the hole where "a" and "b" intersect on the lock body. The hole should be drilled 0.19 inch (3mm) deep
  6. Remove the lock cylinder by pushing a small drill bit or piece of wire into the hole and pulling the cylinder out. It might be easier to insert the ignition key, turn it to the right a little and pull on it.

To install:
  1. Insert the lock cylinder into the housing with the key in the cylinder.
  2. While gently turning the key side-to-side, press the cylinder in to the stop. It should click into place.
  3. Temporarily fit the steering wheel onto the splines, then make sure the column locks and unlocks smoothly.
  4. Install the switches, column covers, wiring and the steering wheel.
  5. Connect the battery cable.

1995-99 Cabrio, 1993-99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal.


NOTE Always use a new shear pin when installing the lock cylinder.

Posted on Oct 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just installed a new key switch in my 2006 trailblazer it is a napa part now when I start it it will only run for a few seconds and die ?


That is because of the vehicle theft deterrent system ! Do you have a security light lit on the instrument cluster ?
The Passlock?"¢ System is provided in order to prevent vehicle theft if the ignition lock cylinder is forced to rotate or the ignition switch is operated while separated from the ignition lock cylinder case. If starting is attempted without authorization from the Passlock?"¢ System, the powertrain control module (PCM) will disable engine starting. Start disable may be in the form of fuel disable or starter disable, depending on engine application.
The components of the Passlock?"¢ System are as follows:
?€¢
The ignition lock cylinder and key


?€¢
The ignition lock cylinder case, including the Passlock?"¢ sensor


?€¢
The ignition switch


?€¢
The body control module (BCM)


?€¢
The security indicator on the instrument cluster


?€¢
The powertrain control module (PCM)

Ignition Lock Cylinder Case, Including the Passlock?"¢ Sensor
The ignition lock cylinder fits inside the ignition lock cylinder case and operates the ignition switch when turned by a key with the proper mechanical cut. When the ignition key is used to turn the ignition lock cylinder to crank, start, a magnet on the lock cylinder passes close to the Passlock?"¢ sensor within the ignition lock cylinder case. The magnet activates the security hall effect sensor in the Passlock?"¢ sensor which completes a circuit from the security sensor signal circuit through a resistor to the security sensor low reference circuit. The resistance value will vary from vehicle to vehicle.
If a magnet from outside of the ignition lock cylinder case is used to attempt to steal the vehicle, the tamper hall effect sensor will be activated. This completes a circuit from the security sensor signal circuit through a tamper resistor to the security sensor low reference circuit bypassing the security resistor. If the ignition switch is forced to rotate without the correct key, or if the ignition lock cylinder is removed by force, the Passlock?"¢ sensor will be damaged and will not operate.

Feb 22, 2015 | 2006 Chevrolet Trailblazer

1 Answer

Need to replace ignition switch


Ignition Switch (2005 Chevrolet Venture listed but the 2006 Venture was not) Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • The SIR system
    • The upper and lower trim covers chev_vent_ign-swch-harness.gif

    • The wiring harness assembly (D) from the wire harness strap (E)
    • The wiring harness straps (C) from the wire harness assembly (D)
    • The wiring harness strap (B) from the upper tilt head assembly (A) chev_vent_col-bulk-conn.gif

    • The turn signal switch assembly connectors (B) out from the bulk head connector (A) chev_vent_passkey-mod.gif

    • The PASSKEY III (B) off of the ignition lock cylinder case (A) chev_vent_ign-swch-screws.gif

    • The key alarm connector (A) from the ignition lock cylinder case (B)
    • The 2 tapping screws from the ignition switch assembly (C)
To Install:
  1. Install or connect the following:
    • The ignition switch assembly (C) onto the ignition lock cylinder case (B)
    • Two tapping screws into the cylinder case.
      1. Torque to: 42 inch lbs. (4.7 Nm)
    • The key alarm connector (A) into the ignition lock cylinder case (B)
    • The PASSKEYS III (B) onto the ignition lock cylinder case (A)
    • The turn signal switch assembly connectors (B) to the bulkhead connector (A)
    • The wiring harness assembly (D) into the wiring harness strap (E)
    • The wiring harness strap (B) into the steering column tilt head assembly (A)
    • The wiring harness straps (C) onto the wire harness assembly (D)
    • The upper and lower trim covers
    • The SIR system
prev.gif next.gif

Sep 25, 2010 | 2006 Chevrolet Venture

1 Answer

My golf gti service light is flashing and the car is chugging


My VW Golf gti. I have just had a service and my sevice light come on when i turn on the ignition, can you tell me how to turn it off please

Jan 19, 2010 | 2001 Volkswagen GTI

1 Answer

Location of ignition switch on 2006 gmc envoy


PATH: Chassis Electrical > Instruments & Switches > Ignition Switch > Removal & Installation Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disable the airbag system, as outlined in the Chassis Electrical Section.
  3. Remove the hush and knee bolster.
  4. Remove the steering column trim covers.
  5. With the key installed, turn the key to the RUN position.
  6. Install a hex wrench into the hole on top of the lock cylinder housing. Push down on the hex wrench to release the tab on the lock cylinder inside the lock cylinder housing.
49901b3.gif
Push down on the hex wrench to release the tab on the lock cylinder inside the lock cylinder housing

  1. Slide the lock cylinder out of the lock cylinder housing.
  2. Disconnect the passlock and key buzzer from the lock cylinder housing.
  3. Insert into the lock cylinder housing
0bc8f9a.gif
Release the tabs on the ignition switch using ignition switch connector release tool J 42759

  1. Pull the ignition switch out of the lock cylinder housing.
  2. Disconnect the connector from the ignition switch.
To install:
  1. Verify the alignment of the gear in the ignition switch. If gear is not in position shown, turn gear in ignition switch until you reach the correct position.
  2. Use a screwdriver to rotate the lock cylinder housing gear counterclockwise until it hits a stop. In order to reach a stop while rotating the lock cylinder housing gear you MUST push and hold in the solenoid on the electric park lock.
  3. Connect the connector to the ignition switch.
  4. Insert the ignition switch into the lock cylinder housing. The tabs on the ignition switch MUST be seated inside the lock cylinder housing for proper installation.
  5. Use a screwdriver to rotate the lock cylinder housing gear clockwise to the start position—allowing it to spring return into the RUN position.
52c72cb.gif
Use a screwdriver to rotate the lock cylinder housing gear clockwise to the START position

  1. Align the lock cylinder and install the lock cylinder into the lock cylinder housing.
  2. Connect the passlock and key buzzer into the lock housing.
  3. Install the steering column trim covers.
  4. Install the hush and knee bolster.
  5. Enable the airbag system, as outlined in the Chassis Electrical Section.
  6. Connect the negative battery cable.

Oct 12, 2009 | 2006 GMC Envoy

1 Answer

How do I install an ignition lock-2001 VW Jetta


their is a pin that need to be pushed down to remove the barrel but you cannot access this from the outside .the last one i done i measured it up with the new one then drilled a hole where it should be according to the new one .The lock has to be in the aux position to push the pin in once you have worked out where to drill the hole .If i remember rightly i removed the whole steering coloumn to drill the hole with a small drill bit then realised it was out a bit so i drilled it out with a bigger bit ,changed barrel and refilled hole with some filler and painted it silver so couldnt be called a bodger

Aug 22, 2009 | 2006 Volkswagen Jetta

2 Answers

Vw golf mk 4 electrical problem


CHECK AUXILIARY BELT FOR DAMAGE AND ALTERNATOR BRUSH LENGTH

Jul 20, 2009 | 1999 Volkswagen Golf

1 Answer

Vw Jetta 5 key will not go all the way into ignition


It's a relatively common problem with MkV VW's. Your ignition has a small plastic spring loaded dust cover inside the lock cylinder. If it gets out of whack, it doesn't actuate the way it should. Try reading this for more info:

http://forums.tdiclub.com/showthread.php?t=207047

Jul 16, 2009 | 2006 Volkswagen Jetta

1 Answer

My key will not go into the ingition.


when the steering wheel is locked, simply put the key in the ignition, then turn the wheel and turn the wheel at the same time and it unlocks the key cylinder

Mar 25, 2009 | 2008 Volkswagen Jetta

7 Answers

My key will not go into the ingition.


Just had the issue on my 2006 GTi. I used 3-1 oil and pushed the key in until it stopped. If you look into the ignition, there is a little grey tab. That is the part you need to settle back in. I pushed the key forward and back a couple times until I heard a "click". I looked in and the tab had reseeded. My key then went in. Jerking the steering wheel doesnt help. nor does forcing it the key in. Use lubricant and a method to allow the lubricant to work its way into the grey tab. www.nftuboise.com

Nov 20, 2008 | 2006 Volkswagen GTI

Not finding what you are looking for?
2006 Volkswagen GTI Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...