Question about 2001 Ford F350 Super Duty SuperCab

2 Answers

How to put last washers on front bearing hud

How to put front axle back toghether

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Metal washer, then plastic washer, then metal washer, then snap ring.

Good luck

Posted on Jun 18, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 70 Answers

If you are refering to the three that go on the axle shaft then the snapring goes on , then you would the plastic one in between the two metal ones, then the snap ring goes on . Thankyou Please rate this answer. This would help me out greatly. RJ

Posted on May 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Buick lasabre when driving slow I can hear cracking noise left front tire I replace the HUD assembly and put new tires on front


Make sure wheel nuts are tight and torqued properly. Inspect hub assembly bolts and axle nut for proper torque as well

Jul 12, 2015 | Buick Cars & Trucks

1 Answer

How do you adjust the rear wheel bearing?


Rear wheel bearings on front wheel drive vans are much like front wheel bearings before front wheel drive.
You have an inner and outer bearing with a nut and lock washer.
After the bearings are packed with grease, you tighten down the axle nut until snug then back it off a notch. Then put the lock washer or lock ring on. Some have a cotter pin to hold the nut in place.
The wheel should spin with no drag from the bearings.

Jul 07, 2012 | 1993 Plymouth Voyager

1 Answer

Replace front wheel bearing


The front wheel bearing for your Impala is an integrated wheel hub/bearing/ABS.
The whole thing gets replaced. It should look like the one off my Bonneville; Bearing.

Remove wheel/tire. Remove brakes. Remove rotor. Remove axle nut. Press-out axle shaft*. Unplug ABS connector. Remove 3 bearing bolts.

*To press out axle, you may need a special tool from an auto parts store.
Don't forget to put the heat sheild back on during reassembly, and the axle nut need to be very tight.

zeevert_62.jpg


After Bearing/hub removed:
zeevert_73.jpg

Apr 21, 2011 | 2004 Chevrolet Impala

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

Repair hud assenbly front


If you are talking about the front wheel hub assemblies, the bearing is pretty difficult to replace. It can not be repaired or adjusted.

I have a 2002 Escape and have replaced the front wheel bearings. Here are some instructions and pictures:

I have a 2002 Escape and have changed my bearings. The front wheel bearings on the Escape are simple cartridge bearings, or Gen1 bearings, that are pressed onto the hub and knuckle. They are not so simple to replace. Unless you have the experience and tools, you'll need to take it to the dealer or a shop.

You will need a press and the correct press tools.
The knuckle/hub assembly needs to be removed from the vehicle.

Here's the short version:
Remove the tire/wheel.
Remove the brake caliper w/ bracket.
Remove rotor.
Remove the ABS sensor.
Remove axle nut and press the axle inwards, until loose. (sometimes easy, usual needs special tool).
Remove the strut bolts, tie rod, and the lower ball joint from the knuckle/hub assembly. Each of these connections can have it's issues.
Press the hub out of the assembly. One half of the inner race will be stuck on the hub. Use a bearing splitter to remove that half.
Remove the snap ring from the knuckle.
Press the rest of the bearing from the knuckle.
Press the new bearing into the knuckle. Press on the outer race only!
Snap ring.
Make sure the dust sheild is still in place.
Press the hub into the bearing. The bearing must be supported on the inner race only!
The point is that you must not press thru the balls in the bearing. That can cause the bearing to get brinnelled.... not good.
Reassemble the knuckle on the vehicle in reverse order. I like to put a little grease on the axle spline. The axle spline has a little helix on it... about half a degree. It's supposed to be a tight fit. The torque on the axle nut is 300Nm (about 220ft-lbs?). This torque is very, very important. It is needed to keep the bearing together and at the correct preload, so use a big torque wrench.

...or you can take it to the dealer.

Good luck.

cimg1162.jpg
cimg1165.jpg
cimg1256ss.jpg
cimg1241.jpg

Dec 30, 2010 | 2003 Ford Escape

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

1 Answer

How do you get back brack drum off, do you have to remove center nut


In the center of the hud, there is a steel cover. use a screw driver and a hammer to tap the cover off. Make sure you take the handbrake off, and undo the center nut and take the bearings out. when you pull the hud off.
When you come to put it back on make sure you put the bearing in first then the washer then the nut.

I hope this has helped!

Jul 09, 2009 | 2000 Ford Focus

1 Answer

What tools do i need to replace front wheel bearing hub assembly


Floor jack- jack car up and put a jack stand under it. A tire lug to remove tire. A 36 mm socket to unbolt axle shaft sticking through bearing hub. Next a Brass hammer with a block of wood. Next center wood on axle shaft sticking through bearing hub and hit with a 4lb brass or steel hammer with a wood block on shaft. Next you need a 10mm or 12mm socket on back side of bearing hub should have 3 bolts holding it unbolt. Last use a pry bar and gradually pry bearing out and no there not pressed in like a lot of people think.
(Socket sizes maybe different)
If you take it somewhere it would cost about $800 and up.

May 03, 2009 | 2000 Pontiac Grand Am GT

1 Answer

How do replace front axle bearings on a 92 jeep


You have to pull off the wheel, brake assembly, and rotor. If it is a 4x4, i suggest you take it to a mechanic. If it isn't, once you pull all that off you will see a little cap cover. take a small screwdriver and pop off the cap. There will be a clip. pull off the clip and pull out the axle bearing. Make sure you grease the axle bearings before you put the new one in. Then put it back together in the reverse of these instructions. Hope this helps.

Apr 30, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Ford F350 Super Duty SuperCab Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...