Question about 1997 Buick LeSabre

1 Answer

What type of bolt fits into the a/c compressor that attaches the a/c lines to the compressor for a 1997 buck lesabre

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 4,340 Answers

This job requires special tools and special training. If you lack either, you risk SERIOUS personal injury.

You need to address oil levels, proper and legal refrigerant recovery, system evacuation, and recharge.

You were planning to also replace the receiver/dryer, correct? It also needs the oil in it measured and incorporated into the amount of oil (in %) that would need to be added. FAILURE to address these and other issues will guarantee premature system failure and likely compressor damage.

Take this job to a qualified shop.

Posted on May 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove ac compressor from 2000 buick lesabre


Have AC drained, remove serp belt, jack up car and remove lower front access panels, unplug wiring , remove 13or 15mm bolt from manifold lines on back of compressor,remove the 4 mounting bolts.

Jul 29, 2014 | 2000 Buick LeSabre

1 Answer

How to fix struts on a 19997 buick lesabre


You need to rent a strut spring compressor before you start to loosen any bolts. Better instructions can be found in a Chilton manual or the how to books sold at auto parts stores. If you're not familiar with mechanical parts of your car, I'd leave it to a professional.

Jun 28, 2014 | 1997 Buick LeSabre

1 Answer

1990 buick lasabre bypass pulley


you have to remove the compressor, the pulley bracket will bolt to where the compressor was, it should line up with the threads from the original bolts.

Oct 11, 2012 | 1998 Buick LeSabre

1 Answer

How to install a/c bypass pulley on 1988 buick park avenue


Most ac bypass pulleys simply bolt on where the ac compressor was. when you remove the compressor save the bolts. AC bypass pulleys are car specific. Each one is made to fit a specific engine. there is no such thing as a universal so make sure that you have the correct one.

May 31, 2012 | 1998 Buick LeSabre

1 Answer

How to replace the fuel filter


the fuel filter is located under the car, it is an inline type bolted to the underbody and attached to the main line with quick connect fittings. you will need to relieve the fuel pressure from the system before you attempt to disconnect the filter. the older these cars get, the more brittle the connectors can be, so be careful when working with the connectors, this is also harder to do if you are not on a hoist. going to a shop to have it replaced may be a good idea.

Jan 28, 2012 | 1994 Buick LeSabre

1 Answer

What type of freon for the 1997 plymouth grand voyager


the freon type should be a decal under the hood somewhere if its not missing as well as the amount of freon required.if no decal then if the fittings for the hose that attaches to the a/c lines are threaded then this will take R12 freon.if the fittings don`t have threading(like quick release fittings) on them then it will take R134 freon.

Jun 09, 2011 | 1997 Plymouth Grand Voyager

1 Answer

How to install a power steering pump for a 1997 chrysler seabring conv


Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

May 13, 2010 | 1997 Chrysler Sebring

1 Answer

Front barke caliper bolts on 97 biuck leasbre what type and size


You will need to climb back there with a flashlight and look. I believe they are allen bolt, and they auto parts store will sell a kit with 3 of the most used allen bolts drivers in a 3/8" socket set.

Alternative is that the bolts may be torx, in which case, the auto parts store will have those as well.

The nice thing is, the sizes are very common, and the driver kit's normally have the 2-3 sizes that are most common for brake repair.

Jan 28, 2009 | 1997 Buick LeSabre

Not finding what you are looking for?
1997 Buick LeSabre Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...