Question about 2002 Audi A6

1 Answer

Clicking noise from the flasher relay when i use blinkers

Clicking noise from the flasher relay when i use my blinkers

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,705 Answers

That's normally a good sign.

I'd just check them out, switch on the 4 way flasher/emergency lights and walk round the car. If they're flashing on all 4 quarters. Its OK.

Posted on May 30, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2000 Dodge Durango and we have been having blinker problems too lately. Sometimes they worked, sometimes they didnt, and the other day they went out completely.They have been doing this for a...

that vehicle has a desperate relay for the hazards which is why they work, you have a defective signal flasher sometimes called a signal relay, follow the noise to locate exactly where the part is, usually under driver side of dash, it is a very cheap part and easy to install.

Sep 26, 2011 | 2000 Dodge Durango

1 Answer

My left blinker sometimes works and sometimes doesn't and also sometimes I hear a clicking noise when I turn it on then it quits working. Is there a flasher relay for the turn signal, and if so where...

there is a flasher relay for the signals and its located behind the dash on the drivers side sometimes in the lower area of the dash.when the signals are working listen to the clicking noise to narrow down the area the flasher will be in.if all else fails you can go to the library and look for a book on your car and it will have the location in it.also if you know a tech he can help you locate it as well.

Sep 12, 2011 | 2004 Chevrolet Tahoe

1 Answer

My turn blinkers completely stopped working. Not even a ticking noise occurs when i "turn-on" a blinker. I am trying to replace the flasher relay unit to see if this fixes the problem, but my...

Try replacing the turn signal flasher first.It should be above the drivers feet near the steering column and looks like a typical flasher unit. A little round canister with 2 wires,sometimes 3 wires.It is what you hear clicking when using the turn signals.

May 30, 2017 | Nissan Maxima Cars & Trucks

2 Answers

How do you replace the blinkers flasher under the dash on a Chev S-10?

This one may be mounted directly on the fuse box or on a plug end. Turn the key on and then the blinker switch. I assume it is bad and quit working though so disregard that last idea if it is bad and not making the clicking noise any longer. It should be a little round or square silver relay. Just pull it off the end where ever it is located. If it is stuck then pull hadder being careful not to pull the wire off with it. It will come off.
It will have two maybe three metel prongs that plug it in. Just replace with new on. Thy have different levels of noise you can buy. If grandpa is getting hard of hearing and forgets to turn his blinker off then you can get a louder one. Let me know how you do on this. Raz

Apr 18, 2010 | 1995 Chevrolet S-10 CA Edition

1 Answer

I cannot find the blinker solenoid

I hate to be the bearer of bad news... but there is NO such thing as a "Blinker Solenoid" . someone may be playing a joke on you. or they are mis informed themselves. there is a flasher relay though . that controls your 4 way flashers, as well as your turnsignal, thats the clicking noise you hear under dash above left foot, when turn signal is on. Hope this helps.

Apr 06, 2010 | 1991 Nissan Maxima

2 Answers

There is a clicking noise after blinker is ued. i have 2001 pontiac grand am, 4 door, auto,4cyl. what causes that?

Common problem with Grand ams. Your blinkers are wired into the warning flasher relay. The warning flasher button is located on the center of the dash with a red triangle emblem on it. Behind that button in the dash is a relay that is about 5 inches long. It needs to be replaced. Good luck!

Nov 07, 2009 | 2001 Pontiac Grand Am SE

1 Answer

Where is the flasher relay unit

1ST double check that all the bulbs for the pass. side turn signals are working. if even one is out it can make the blinker not "blink". so compare the pass. side lights to the driv. side to make sure u did not miss something. NEXT,if thats not the problem, then u can locate the flasher by 1ST looking in the fuse box(probably inside the glove box or under the drivers side dash) theres a good chance it might not be there(years ago every car had the flasher in the fuse box) SO TURN ON THE DRIVERS SIDE BLINKER (key on) and LISTEN OR FEEL UNDER THE DASH FOR THE FLASHERS NOISE--LOOK NEAR THE STEERING COLUMN,BRAKE PEDAL, EVEN BEHIND THE ASH TRAY!! hope this helps you!

Sep 07, 2009 | 1994 Buick Century

1 Answer

Blinker relay 1985 cadillac

Should either be on the under-dash fuse panel or under the edge of the dash near the steering column. To figure out if you are looking at the directional flasher or the four way, turn the hazard flasher on and find that one first. the directional one is identical but will be making no clicking noise.

Jun 16, 2009 | 1998 Subaru Forester

1 Answer

Blinkers will not stop making noise

its time to replace your flasher relay

Jun 03, 2009 | 1999 Ford Crown Victoria

1 Answer

Flashers out, module, relay

More than likely to be a flasher relay. If you can locate the relay turn the harzards on and tap the relay with the ennd of a screewdriver. If the hazards start to work for a moment when being hit you know its the relay. If it was a module i would of thourght you would have more electrical problems as modern cars are mutiplexed meaning one module controls lots of different things. hope this helps.

Jun 01, 2009 | 2000 Dodge Stratus

Not finding what you are looking for?
2002 Audi A6 Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

76070 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14362 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides