Question about 2004 Ford F150

1 Answer

2004 Back-up sensor cut-off switch replaced, still B/U sensors do not indicate upcoming people.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 70 Answers

The more common failure is one of the backup sensors, testing with a scanner will indicate which sensor in the system has failed and causing the Park aid to not work. You must have this info to test the system. Please rate this answer for me THankyou RJ

Posted on May 30, 2010

Testimonial: "Very helpful. I did not know that if one sensor went out the others would not respond. Is that correct? If so, how can I identify the sensor that is bad? Thanks, DC"

  • 1 more comment 
  • rjlauria47 May 30, 2010

    Yes that is correct , the computer turns off the system in the event one sensor fails to prevent it from giving you incorrect info. The computer monitors the inputs received and dissables the pam(park aid module) this lets you know there is a fault and need to have the system serviced. Thankyou RJ

  • dcranford237 May 30, 2010

    THank you very much for the info. I will try to isolate the correct sensor.

    Great day,
    DC

  • rjlauria47 May 30, 2010

    Your welcome have a good one.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does code P2197 On town car 2004 means?


P2197 - Lack of HO2S-21 Switch, Sensor Indicates Lean
A Heated Oxygen (HO2S) sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time. See the possible causes for DTC P2195.

Dec 24, 2015 | 2004 Lincoln Town Car

1 Answer

ERREURPO132 DODGE CARAVAN 3.3 LITRE 2004


This involves the front oxygen sensor on Bank 1. This code indicates that the heated oxygen sensor reading incorrectly
You will likely not notice any drivability problems.A code P0132 may mean that one or more of the following has happened:
  • The oxygen sensor heater circuit is shorted out
  • The wiring to the sensor is broken / frayed (less likely)
The simplest thing to do is to reset the code and see if it comes back.If the code comes back, the problem is more than likely the front Bank 1 oxygen sensor. You will likely wind up replacing it but you should also consider these possible solutions:
  • Check for wiring problems (shorted, frayed wires)
  • Check the voltage of the oxygen sensor

Sep 10, 2014 | 2004 Chrysler Voyager

1 Answer

I have a 1996 GMC C1500 Suburban. Service engine light is on. Free diagnostic at Advance Auto Parts says "bank 1 too rich". Replaced mass airflow sensor, idle air control valve, all 4 O2 sensors,...


A vacuum hose cut will cause a lot of symptoms, A code indicating a rich conditions indicates a lack of air, or too much fuel. A dirty air filter or a leaking injector will cause this. A faulty O2 sensor will also cause this condition.

Apr 03, 2013 | Cars & Trucks

1 Answer

Could po320 be drive shaft speed sensor


code p 0320 refers to crankshaft position (CKP) sensor /engine speed (RPM) sensor---circuit malfunction====causes --wiring--CKP/RPM sensor ---ECM check the wiring to the crank position sensor
replace the crankshaft position sensor

Apr 16, 2017 | 2004 Jeep Grand Cherokee

2 Answers

P2138 code for a 2004 dodge ram 5.7 liter


Were the APP codes there BEFORE they replaced the BCM? APP codes usually are an indicator the throttle body needs to be replaced. As a precaution, some recommend to replace the throttle body AND the sensor on the gas pedal together. Unfortunately, this is a dealer only repair most o the time, since the ECM will have to be flashed to sync the new sensors.

Dec 13, 2012 | 2004 Dodge Ram 1500

1 Answer

Reseting the brake sensor in a 2004 s mini cooper


did you replace the sensors when the pad wears it cuts a wire on the sensor if you look at the sensor you will see it

Apr 28, 2012 | 2004 Mini Cooper

1 Answer

2004 gto ls1 motor is running rich and dtc code is P0131


that would be your best bet it is very hard to diagnose a injected v8 with out the right equipment but speaking from experience ( due to the fact we in Australia built these cars) the oxy sensors cause all sorts of problems and swapping them over does't necercarly prove much

Dec 06, 2008 | 2004 Pontiac GTO

3 Answers

2004 Audi A4 3L won't start


P0130 is 02 sensor bank 1 and P0150 is 02 sensor bank 2.

Aug 19, 2008 | 2004 Audi A4

Not finding what you are looking for?
2004 Ford F150 Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...