Question about 1996 Honda Accord

2 Answers

I have a 96 honda accord and changed the clutch master cylinder and the slave cylinder and bled the system there still is no clutch pressure

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 4,336 Answers

You need to PRE BLEED the master cylinder, or you may never get pressure. Parts houses sell little hoses for this purpose.

Posted on May 30, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Check all of your lines, make sure there is nothing leaking..also make sure that the bleeding nipple on the slave is shut all the way and also the one on the master. if there is nothing leaking and all lines are tight try to gravity bleed, open the nipple on the slave and let the fluid drain out. the fluid will stop when there is no air in the lines, while you do that try tapping on all the lines to make sure there is no air pockets getting stuck..i had the same problem in my honda and that worked perfectly

Posted on Jan 22, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1999 accord wont shift into gear while its on but will when its off its a 5 speed.


It's your hydraulic clutch system that probably isn't working. When you press the clutch pedal down, it causes the clutch master cylinder to put pressure in the line to the transmission's little "slave cylinder" that operates the clutch inside the transmission bell housing. This disengages the engine from the transmission so you can shift gears. It's probably not putting the slave cylinder to work by hydraulic pressure. The clutch master cylinder is mounted on the firewall, similar to the brake master cylinder, the clutch cylinder has a reservoir and you may need to add brake fluid to it. If it is dry, then you will need the system bled at the slave cylinder by a pro or someone who understands how. Pretty simple, really, just like bleeding brakes. Also the clutch master cylinder can develop internal leaks and this will lead to loss of clutch.

Nov 02, 2015 | Cars & Trucks

1 Answer

I have no pressure on my clutch in my 2001 honda civic and the clutch and master cylinder are new.


How recent is the replacement of the master and slave? Sounds as if the system has air in it and needs to be bled properly

Sep 06, 2015 | Honda Cars & Trucks

3 Answers

I just replaced clutch on 1993 Honda accord ex and the release cylinder isn't pushing the release bearing enough to shift when car is running


I really need more info such as...Mileage,did you do the job yourself,if so was the slave cylinder and or clutch master cylinder changed and did you bleed the system..?...So I will explain without knowing,,...Before a clutch wears completely out we find ourselves constantly working the clutch pedal stressing all clutch system components..In most cases I have looked closely and found slave cylinder and clutch master cylinder leaking ..however the slave cylinder can wear out without leaking..Most importantly the fluid itself wears out every 15 to 20,000 miles.. You don't notice but the fluid gets thousands of tiny air bubbles in it and makes the clutch weak and spongy..(Same with brakes)..You should always bleed system with an assistant just as you would a brake system..,This alone will cause the problem you are experiencing...If you already know that and you have bled the clutch system then you know the slave cylinder is at fault..(UNLESS THERE WAS SOME TYPE OF MISALIGNMENT WITH RELEASE BEARING....YOU SHOULD ALWAYS CHANGE RELEASE BEARING WITH FORK WHEN DOING A CLUTCH SERVICE..)...I assume you did...I would inspect for leaks..,Bleed it again if no leaks...If that don't help and no leaks are found change slave cylinder and or master cylinder.....I hope this helps........Brooks/Metalpoet.......

Jun 13, 2014 | Cars & Trucks

1 Answer

I have a 94 honda accord standard transmission. The clutch drops to the floor after about 4 or so pumps, I pull it back up with my foot and it gets pressure again. The master and slave cylinders are full...


If it loses pressure after a few pumps, either the clutch master cylinder and/or clutch slave cylinder are defective, or there is a leak elsewhere in the system. Also low RPMs and low power are usually due to the ignition timing being incorrect. An incorrectly installed timing belt can also cause low power.

May 10, 2014 | Cars & Trucks

1 Answer

I have a honda accord coupe 94 the clutch stops workin after i start the car i ihe car doest accelerates


If you mean you step on the clutch, put transmission in gear and release clutch with no engagement (pedal returns to top position) there is a good chance your clutch disc or pressure plate, or both are worn out and need replacing.
If your clutch pedal is going to the floor and not returning there could be a leak in the system, a bad clutch master cylinder or a bad slave cylinder on the transmission. Check the fluid level in the clutch master cylinder. If it is low or empty you have a leak or component failure. Visually inspect clutch master, line, slave cylinder for fluid leaks. replace as needed. If hydraulics are o.k., suspect clutch disc/pressure plate.

May 09, 2014 | 1994 Honda Accord

1 Answer

Piston on new slave cylinder not moving


Gravity will not bleed the system as you need pressure in the master cylinder to bleed out the air. Once you have pressure bled the system you will have a good clutch

Nov 16, 2013 | Chevrolet S 10 Cars & Trucks

2 Answers

Ok i have a 92 honda accord ex 5 speed. i have no pressure in my clutch pedal. i replace the slave cylinder and bled the whole system. a bunch oh thick gunk came out. and the car was fine. two weeks later...


You need to replace the slave cylinder, it is contaminating the system fluid with rubber seal gunk, this is ruining the new masters. The clutch slave and master should always be done as a pair. This advice comes from 35 years of work experience.

Jan 25, 2012 | 1992 Honda Accord

1 Answer

Clutch pedal goes to floor no preasure filled and bled slave cyl same result


Hi:
If you have bled the system, you are down to either having a bad clutch master cylinder, or a bad clutch slave cylinder. You could eliminate the slave cylinder by removing the line and capping it off, and if you have a firm pressure on the clutch pedal ( don;'t try to push it down, just check for pressure!) then your slave cylinder is bad. If you cap off the line, and bleed the system, and the pedal still has no pressure, then your clutch master cylinder is bad!

Apr 15, 2010 | 2004 Chevrolet Cavalier

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

1 Answer

1996 honda accord clutch goes all the way to the floor


check the slave and clutch master cylinder for leakage. look under the dash , at the clutch master) push rod attached to the clutch pedal) . try to see if there are any leaks around it. if so have it replaced and have the system bled to remove all fluid and air stuck in the system.

Apr 04, 2009 | 1996 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...