Question about 2002 Ford Explorer

1 Answer

Key will not come out of ignition when engine is turned off and steering wheel won't lock. Key is released after disconnecting battery.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 102 Answers

Im thinking it mght be somthig to do with your linkadge . it might not think it,s in park ...take a look it,s my best id

Posted on May 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

When you put the key in the ignition the key will not turn. The steering is locked


try turning the wheel hard to the left or hard to the right while turning the key, The wheel is probably just locked.

Mar 24, 2015 | 2002 Dodge Caravan

2 Answers

Why can't I unlock my ignition and start my car?


Put one hand on the steering wheel and rotate slightly left and right alternatively whilst turning the ignition key at the same time with the other hand. This might release the steering wheel and start ignition.

Hope this helps.

Aug 02, 2014 | 2008 Infiniti G35

4 Answers

Ignition key won t turn


The ignition key won't turn likely because the shifter linkage that locks the key in OFF is worn or loose. Move the shifter linkage hard to the Park position and the key will turn. Have the linkage adjusted and the worn parts replaced

Mar 30, 2014 | 2000 Mercury Grand Marquis

1 Answer

Key won't come out of ignition on 1999 vw jetta


IGNITION KEY WILL NOT RELEASE

It can be faulty ignition lock cylinder. I suggest to wiggle the steering wheel a bit and see if the key gets released out. If that is not helping then first turn steering wheel to right and try removing the key, or next turn steering wheel to left and see if you can remove the key.

----------

Spray wd-40 in the ignition key hole and let it remain there for few minutes, after that once again try to remove the key and see if that helps.

---------

But if that is not helping then ignition lock cylinder has to be removed out and key has to be manually removed.

-----------

For more troubleshooting on these types of issues, I suggest you to refer the help links mentioned below. Its the accurate solutions mentioned in it. That will help you to narrow the problem: -----

Click the link below: ------


-----------

1999 Toyota Camry: Key Will Not Come Out Of Ignition?

http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-key-will-not-come-out.html

---------------

2001 Toyota Tacoma: Ignition Locked?

http://technoanswers.blogspot.in/2012/04/2001-toyota-tacoma-ignition-locked.html

------------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

-----------

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

-----------

Ignition Key OFF but engine still running?

http://howtobyme.blogspot.in/2012/03/ignition-key-off-but-engine-still.html

--------------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

-----------

Ignition locked up on Mercury Villager?

http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html

-------------

Key won't turn in the ignition on Toyota land cruiser?

http://technoanswers.blogspot.in/2012/02/key-wont-turn-in-ignition-on-toyota.html

-------------------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

-----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html

------------------

These will help.

Thanks.

Feb 15, 2013 | 1999 Volkswagen Jetta

1 Answer

Key in ignition won,t turn 2004 ford escape


several things, does key go in and out easily, turn steering wheel in both directions while turning key. sometimes the steering wheel lock binds the lock cylinder and turning wheel releases the pressure and it will turn. other than that the ignition cylinder is jammed, wet key lightly with lubricant such as wd-40 and a light bit in key hole and try key again, If key is heavily worn out , try a different ignition key as it might not be disengaging all the tumblers in lock, if all this fails you need a new cylinder.

Jun 09, 2012 | Cars & Trucks

1 Answer

What is the procedure to changing an keyed ignition lock?


Hi there,

Removal

Disconnect the negative battery cable with the proper size wrench and place away from the battery.
Insert the key into the ignition lock cylinder and turn the key to the run position.
Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.
Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.

Installation

Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
Install the electrical connector back into the connector housing by pressing it in with your hands.
Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.

Hope these help.

Jan 28, 2011 | 1992 Ford Crown Victoria

1 Answer

I can't get the rod that connects the key lock and door latch in the right position to work correctly.


  • Disconnect the negative battery cable with the proper size wrench and place away from the battery.

    Insert the key into the ignition lock cylinder and turn the key to the run position.
  • 2 Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
  • 3 Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.

    Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.
  • Installation
  • 1 Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
  • 2 Install the electrical connector back into the connector housing by pressing it in with your hands.
  • 3 Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
  • 4 Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.


  • hope this helps you

    Dec 21, 2010 | Ford F-350 Cars & Trucks

    1 Answer

    Ignition switch unable to turn car on key is hard to mget into switch nassemblyn I tried a new key that came with the vehicle


  • Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.
  • 2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.
  • 3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.
  • 4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.
  • 5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.
  • 6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.
  • Dec 04, 2010 | 2007 Honda Ridgeline

    1 Answer

    Install a Ignition lock cylinder 1997 Pontiac Grand Am


    • Ignition Removal Instructions
    • Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
    v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
    • Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle or Steering Column Trim Covers - Disassemble - Off Vehicle .
    • Put the key in the steering column lock cylinder set (1).

    • Turn the key to the "START" position.
    • Install a 1/16 allen wrench (2) into the hole on top of the lock module assembly in order to release the steering column lock cylinderset retaining pin.
    • Turn the steering column lock cylinder set (1) into the "RUN" position.
    • Pull the steering column lock cylinder set (1) out from the lock module assembly.
    • Remove the key from the steering column lock cylinder set (1).

    19eb1ff.png


    • Installation Instructions
    Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
    • Insert the key into the steering column lock cylinder set (1).
    • LIne up the locking tab (2) and the positioning tab (3) of the steering column lock cylinder set with the locking tab slot (5) and the positioning tab slot (4) in the lock module assembly (6).
    • Push the steering column lock cylinder set (1) into the lock module assembly (6).
    • Rotate the steering column lock cylinder set (1) in the lock module assembly (6) into all positions.
    • Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle or Steering Column Trim Covers - Assemble - Off Vehicle
    • Remove the ignition key from the lock cylinder set (1).
    • Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical

    d612a25.png

    I hope this helps and good luck.
    Please remember to vote 962e1fb.jpg and leave a testimonial. Thanks.

    Nov 02, 2009 | 1997 Pontiac Grand Am

    1 Answer

    Hoe to remove the ignition switch in 05 ram 1500


    Step1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them. Step2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft. Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheelmag-glass_10x10.gif and disconnect the wiring. Slide the spacer sleeve off of the steering column. Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out. Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder. Step6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

    Feb 21, 2009 | 2005 Dodge Ram 1500

    Not finding what you are looking for?
    2002 Ford Explorer Logo

    Related Topics:

    117 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...