Question about 2003 Chrysler Town & Country

1 Answer

I am trying to replace the Camshaft Position Sensor on a 2003 fwd chysler town & country and cannot get it out. I have removed the wire and mounting bolt but it does not want to come out. Any thoughts?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 146 Answers

Try to spray it with wd40. should pull out sometimes the rubber o-rings hold it good. hope this is a help

Posted on May 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the Crankshaft Position Sensor location on a Town and Country with the 3.6L V6 engine?


The role of the crankshaft position sensor is to determine the position of the crankshaft, the crankshaft angle. It is usually with a camshaft position sensor work together - to determine the basic ignition timing. Car Diagnostic Tool

Aug 27, 2016 | 2011 Chrysler Town and Country

2 Answers

PO340 Hard starting.


CODE PO340 IS NO CAMSHAFT POSITION SENSOR CIRCUIT FAILURE.

Jun 03, 2011 | 2003 Chrysler Town & Country

1 Answer

I received a P0340 on my 1995 Nissan Altima. It says I need to replace the Camshaft sensor. The dealers say that my car does not have one in it and that it may be in the distributor itself. Is this true....


They may be right. I cannot find the part. here is what the manual says:


REMOVAL & INSTALLATION The camshaft position sensor is located inside the distributor. On some distributors, the camshaft position sensor is not serviceable (replacement parts may not be available separately). If the camshaft position sensor is serviceable, use the following procedure.

  1. Remove the distributor cap and wires.
  2. Remove the rotor.
  3. Remove the camshaft position sensor cap.
  4. Remove the camshaft position sensor mounting screws.
  5. Carefully remove the camshaft position sensor.

To install:
  1. Position the camshaft position sensor in the distributor and tighten the mounting screws securely.
  2. Install the camshaft position sensor cap.
  3. Install the rotor.
  4. Install the distributor cap and wires.

Sep 27, 2010 | 1995 Nissan Altima

1 Answer

2003 town and country changed plugs and wires and


did you replace the ignition coil? they do give you problem of skipping too.

Mar 13, 2010 | 2003 Chrysler Town & Country

1 Answer

Change cam position sensor chy


  1. Disconnect the negative battery cable.
  2. Detach the electrical harness connector from the camshaft position sensor.
  3. Unfasten the camshaft position sensor mounting bolt. There is a hole in the bracket for tool access to the sensor mounting bolt.
  4. Rotate the sensor away from the engine block.
  5. Pull the camshaft position sensor up out of the chain case cover. Do not pull on the sensor wire.
There is an O-ring on the sensor case. The O-ring may make removal of the sensor difficult. A light tap on top of the sensor prior to removal may reduce the force needed for removal. Inspect the O-ring for damage and replace if necessary.
To install:
If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face and an O-ring is positioned in the groove of the new sensor.
  1. Apply 1-2 drops of clean engine oil to the O-ring prior to installing the sensor.
  2. Install the sensor into the chain case cover and rotate into position.
  3. Push down on the sensor until contact is made with the camshaft gear. While holding the sensor in this position, install and tighten the mounting bolt to 10 ft. lbs. (14 Nm).
  4. Attach the electrical harness connector to the camshaft position sensor.
  5. Connect the negative battery cable.

Oct 13, 2009 | 1996 Chrysler Town & Country

2 Answers

Town and country mini van won't atart


Can you hear the fuel pump run when you cycle the key?

Sep 18, 2009 | 1999 Chrysler Town & Country

Not finding what you are looking for?
2003 Chrysler Town & Country Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...