Question about 1999 Chevrolet Monte Carlo

1 Answer

What tools are need for monte carlo front brake job

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 270 Answers

Hi: You'll Need a Floor Jack ,Jack Stands, To Keep it Safe ,Loosen Lug Nuts on Front Wheels Before You Jack it up. Then After Tires are Off, You'll need a 3/8 Inch Either a Allen L-Shaped Wrench or Even better and i Recommend you Use a 3/8 Inch Socket Type Allen Wrench,Using this you'll need a Ratchet to Fit the 3/8 Inch Socket Allen ,This Allen Socket is needed to Break Loose your Caliper Hold Down Bolts,There Located on Back Side of Caliper Theres On 2 of Them.Then You'll Rock the Caliper Back and Fort until it Comes out of the Caliper Bracket.If its Stubborn you Might Need to Use a Large Screw Driver to get Sme Leveage Under the Caliper to Get it Off.The You'll see the 2-Pads ,HERE Look and See which Pad goes in the Back Side Of Caliper and Which one to The Front Side.Normally the Pad With a Spring Like Tab Goes on The Inside And That Tab Fits into the Caliper Piston.Then you'll Need a Large C-Clamp To Compress the Caliper Piston Flush or Even With The Caliper Housing. You can Use 1 of the Old Pads To Tighten and Compress the Piston Back.The Old Pad you Use will be used on The Piston Side. As Far as Tools Thats Really ALL you'll Need. T\Let Me know How I Helped you By Voting on My Solution i Sent You. Thanks the WYOCWBOY

Posted on May 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad back brake pads


its a good idea to have rear disc caliper compressor. prob can get one from AutoZone (loan/rent)

Nov 19, 2013 | 2005 Chevrolet Monte Carlo

1 Answer

How do you open the hood of a 99 Chevy Monte Carlo after you pull the inside lever....


When you pull the handle, the hood pops up so you can reach in from the front of your Monte Carlo and release the latch to raise the hood

Jun 10, 2013 | 1999 Chevrolet Monte Carlo

2 Answers

1997 chevrolet monte carlo brake problems


Would you care to explain in detail the problems,
& who works on your vehicles & why you have problems

Dec 10, 2012 | 1995 Chevrolet Monte Carlo

1 Answer

How to install timing belt on 96 monte carlo 3.4l dohc


if you don`t have the proper tools to perform this job or the mechanical knowledge to work on motors I strongly suggest you let an experienced technichan perform this job as a lot of techs won`t touch this type of job on this motor

Mar 04, 2011 | 1996 Chevrolet Monte Carlo

1 Answer

200 monte carlo problem


your emergency breck swtich which control with hand breck is faulty, Ist check it. if its ok, than check wire of swtich is short with body, it is midle of both front seats

Sep 21, 2009 | 2000 Chevrolet Monte Carlo

1 Answer

Stalling and brakes wont work properly on 1999 chevy monte carlo


Stalling, could be fuel filter, plugs, plug wires, fuel injectors. Brakes, could be air in lines, defective calipers and pads. Remove one wheel and check the thickness of the pad and look for any leaks. I you intend to replace the pads you will need certain tools, antinseizing compound, and high temp break grease.

Jul 17, 2009 | 1999 Chevrolet Monte Carlo

1 Answer

What tools needed for rear disc brakes on 2002 Monte Carlo


No, all you need is metric wrenches, a big hammer to remove the rotors and a c-clamp to push the piston back in the caliper.

Mar 31, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

Ignition switch replacement 1983 monte carlo


you have to take off the steering wheel.if you dont have the right tools to do so i would not attempt it.the turn signal switch has to be moved it just pulls over the end of the column.then there is a torx head screw at about 1 oclock in the column that has to be removed.and the ign.just pulls out.the dimmer switch is kinda tricky.a locksmith usually dont charge to much to do this job.it would probably cost you more to buy the tools you need to do it yourself

Nov 16, 2008 | 1987 Chevrolet Monte Carlo

Not finding what you are looking for?
1999 Chevrolet Monte Carlo Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...