Question about 1995 Toyota Camry

Open Question

How change ignition switch of toyota camry 1998

How change ignition switch of toyota camry 1998

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

  • 1861 Answers

SOURCE: 1998 toyota camry interior dome light replacement

Look closely at the cover. You will see a small slot. Insert a small flat blade screwdriver, and pry it off. Very easy..

Posted on Nov 10, 2008

landsend
  • 1066 Answers

SOURCE: replace the ignition switch for 1998 toyota corola

first, remove the steering wheel and then remove the top and bottom covers on the steering column

Posted on Mar 26, 2009

  • 318 Answers

SOURCE: 1998 toyota camry , 2 codes, p0171. + p1133

P0171 lean code. Clean the maf sensor. A f sensor is inthe exhaust pipe.

Posted on Oct 27, 2009

  • 563 Answers

SOURCE: change thermostat on 1998 toyota camry

1. Write down your radio code if it has some anti-theft device.
2. Allow the engine to cool down for about 3-hours before the start of this operation.
3. Open the hood, and disconnect the battery negative terminal. Tuck the negative terminal aside so it won't flip back.
4. Locate the radiator drain-plug (plastic wing-nut) on the lower back side of the radiator, and turn it backward to remove it.
5. Place a container under the radiator to catch the anti-freeze coolant.
6. Remove the radiator cap.
7. Once the coolant is drained, trace the upper radiator hose to where it ends on the engine(thermostat housing), and remove the hose with a medium size plier.
8. Loosen the three bolts holding the thermostat housing. Gently take out the housing.
9. Notice the position the thermostat was previously installed.
10. Replace the old thermostat, and the o-ring around it. Clean its mounting area. Notice that the o-ring fits around the thermostat.
11. Replace the thermostat housing and torque the three bolts to 78-inch pounds. Replace the upper hose.
12. Replace the radiator drain-plug.
13. Re-use the antifreeze coolant and be careful no dirt goes in with the coolant into the radiator.
14. Return the radiator cap.
15. Reconnect the negative battery terminal.
16. Start the car and check for leak.

Important: Anti-freeze coolant harmful to the environment. Return unwanted anti-freeze coolant to collection areas.

Posted on Dec 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rem repl ign switch 1998 Toyota Camry


it has break away bolts if I remember correctly...cannot be done with simple hand tools

Dec 29, 2013 | Cars & Trucks

1 Answer

Ignition lock


try a real question using the form.....



http://www.englishclub.com/vocabulary/wh-question-words.htm

Dec 29, 2013 | 1998 Toyota Camry

1 Answer

Change ignition key switch 98 camry


do you have the old key if so....
remove steering column cover 3 to 4 screws on the lower side insert key turn to acc/on position use a small pick tool or something that can fit the small hole underneath the ignition switch its a pin hole push in at the same time pull out the key it will come right out call 704-777-5274 for more support thank you

Sep 05, 2011 | 1998 Toyota Camry

1 Answer

I removed my spark plug wires and forgot which wire goes with which plug for a 1998 toyota camry.


moz-screenshot.pngmoz-screenshot-1.pngmoz-screenshot-2.pngThe firing order is 1-3-4-2

Number one is the one at the pulley end of the motor and number 4 is at the flywheel end of the motor.

System uses a Distributorless Ignition System (DIS) with 2 ignition coils. Cylinders No. 1 and 4 use the same ignition coil. Cylinders No. 2 and 3 use the same ignition coil.

Jun 01, 2010 | 1998 Toyota Camry

1 Answer

Toyota camry 1998 lxe v6 keys lost


IGNITION CYLINDER WEARS NEED TO FILE KEY ALITTLE, USE EMORY CLOTH,,

May 29, 2010 | 1998 Toyota Camry

1 Answer

Change ignition 1998 toyota camry


This Ones Fun It Must Be Very Common As I Just Did It To My 99.
Step 1. Remove Negative From The Battery.
Step 2. Put The Key In The Ignition And Put It In Acc Position.
Step 3. Remove The Steering Wheel Column Covers. I Think 2 Screws On Bottom
Step 4. Unplug Wiring Harness From Ignition
Step 5. Detach The Switch Retaining Screws.
Step 6. Look To The Bottom Of The Ignition And There Is A Youll See The Retaining Pin Push It With A Small Flat Head Screw Driver Or Alike.Then Pull The Key While Holding That Pin Down
And Bam There It Is In Your Hand.
Then Reverse All These Steps Once Sliding In The New Ignition.
If For Any Reason You Do Not Understand Please Feel Free To Ask Me Any Questions.

Dec 17, 2008 | 1998 Toyota Camry

3 Answers

1998 toyota


There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Dec 01, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1995 Toyota Camry Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...