Question about 1998 Dodge Caravan

1 Answer

Signal light where is the fuse located that controlls the signal lights

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 5,763 Answers

The fuse block is located on the leftside of the dash behind the dash, the fuse is located in slot #8 here a diagram of the fuses and there locations.signal light - 97615ef.gif

Posted on May 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

3 Answers

Blinkers don't work at all. Where can I find the fuse or relay? I'm very frustrated. I need help.


Chris, fuse could be down under the dash to the left kind of near where your left knee would be when you are driving or under hood (engine compartment) in the fuse/relay center.
It could also be faulty flasher, wiring, etc
I will post some trouble shooting links for you.
Press the helpful button.
1996 2000 Chrysler Town and Country Interior Fuse Check 2000 Chrysler Town...

How To Install Replace Taillight and Bulb Chrysler Town Country 04 07...

Fuse Box Location in 1999 Plymouth Grand Voyager Van

Quick Tip Signs of blown IOD Fuse on Chrysler Dodge Jeep Fiat or Ram...


Feb 15, 2016 | 2002 Chrysler Town & Country

2 Answers

1982 lincoln mark vi horn and signal lights stop working


The blinker switch has went bad, it is located inside the steering column and will require a steering wheel puller tool to get to the switch

Oct 07, 2014 | Cars & Trucks

2 Answers

I have a 2005 ford f550 with factory brake controler & factory trailer wire plug. On the trailer wiring plug I am not getting power to the turn signals or brake lights. The turn signals and brake...


There is a fuse box under the hood that has the fuses that control the wire harness. There are at least 2 boxes, mine were on the drivers side wheel well near the rear of the engine compartment.

Nov 14, 2013 | 1997 Ford F150 Regular Cab

1 Answer

Nissan Xterra Brake Light Fuse Location


It's 15A FUSE 39 in the fuse & fusible link box

Mar 25, 2017 | Nissan Xterra Cars & Trucks

1 Answer

2003 Yukon XL Denali Trailer Light Problems


Lighting control module ? ?????? Hazard / flasher module ! Now ( there''s not even an electrical signal where the fuse plugs into the interior fuse panel.) What FUSE ??????

Stop Lamps
The STOP LP 25 A fuse in the underhood fuse block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to both the STOP 15 A fuse and the CHMSL 10 A fuse in the I/P fuse block, and to the turn signal/hazard module. The turn signal/hazard module then supplies voltage to both of the trailer rear turn/stop lamp supply voltage circuits. The voltage from the CHMSL 10 A fuse is to the center high mounted stop lamp (CHMSL) and the trailer jumper harness. The voltage from the STOP 15 A fuse is to the stop lamps, throttle actuator control (TAC) module, and the cruise control.
Backup Lamps
The backup lamp request signal is sent from the powertrain control module (PCM) to the body control module (BCM) on the Class 2 message system. This signal is based on the park neutral position (PNP) switch signal. The BCM supplies voltage on the backup lamp supply voltage circuit to the backup lamps and to the automatic day/night mirror. Voltage for the courtesy lamp supply voltage circuit and backup lamp supply voltage circuit is from the TBC B fuse in the instrument panel fuse block directly through the BCM to these circuits. A short to ground on either of these circuits will open the fuse. The backup lamps are grounded at G401.
For trailer wiring, a separate backup lamp circuit is connected through the underhood fuse block from the TRLR B/U 10 A fuse to the trailer wiring harness.
Turn Signal/Hazard Lamps
The IGN E 10 A fuse in the underhood fuse block supplies battery positive voltage to the turn signal/hazard switch assembly. The FLASH 25 A fuse in the I/P fuse block supplies battery positive voltage to the turn signal/flasher module and ground is supplied at G200. When the turn signal switch is placed in either the left or right position, a voltage signal is completed from the turn signal switch to the turn sign/flasher module. When the hazard flasher switch is activated, a ground signal is completed from the turn signal/hazard switch to the turn sign/flasher module. The turn sign/flasher module then sends an on-off voltage signal through the LT TRLR, RT TRLR, LT TURN or RT TURN 10 A fuses in the I/P fuse block to the appropriate turn signal or to all 4 fuses for hazard operation. The instrument panel cluster (IPC) indicators receive voltage from the LT TURN and RT TURN fuses as well as the DDM/PDM for the mirror turn signals. The DDM/PDM has no function or control of the mirror turn signals other that a pass through connection for the circuits. The audio chime is also activated when the turn signals are on. When the hazard switch is pressed, all turn signal lamps will flash including both IPC turn indicators. The front turn signals are grounded at G100. The rear turn signals are grounded at G401. The Mirror turn signals are grounded by the DDM/PDM.

Do you know how to do automotive electrical circuit testing with a test light or volt meter ? How to read an use a wiring diagram to pin point testing points . ( connectors , fuse locations etc... ) How to use a power flow chart ? Here is a site for just such info .

http://www.bbbind.com/free_tsb.html Enter vehicle info . year , make , model an engine size . System click lighting , subsystem exterior lighting . Second diagram shows trailer wiring .
Electric Testing Techniques You Need to Know

Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

CHEVROLET 2007 SILVERADO TRAILER LIGHT TROUBLESHOOTING


Apr 07, 2017 | 2003 GMC Yukon Denali

1 Answer

Signal lights stopped working


If the fuse is good and the flashers work then you have a bad signal flasher, this car uses two flashers in one located under the dash, one controls the hazard lights and the other the signals, these are all inside one flasher, so turn on the hazards to locate it by listening to clicking noise. i have inclosed a diagram to help locate it. its on leftside kick panel by your left foot, replace the flasher and see if that does it, good day12_6_2011_6_03_02_pm.gif

Dec 06, 2011 | 1991 Honda Accord

2 Answers

No brake lights or signals


check your fuses you also have a master fuse that controls these lights signals

Jan 24, 2010 | 1994 Chevrolet Cavalier

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

1 Answer

Turn Signals


The body control fuses are located in the left hand side when the driver door is open. The panel just pops off. All fuses are labeled. Do the signals work on the outside? This would tell me that the dash has been off for service and not replaced properly....accordianman

Jul 29, 2008 | 2002 Chrysler Concorde

Not finding what you are looking for?
1998 Dodge Caravan Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...