Question about 1991 Chevrolet S-10

1 Answer

How to change the starter in 1991 s-10 pickup?

How to change the starter in 1991 s-10 pickup (v-6)? After the bolts were removed, the starter is hung up. Appears that the motor mount may need to be removed and the engine jacked up?
Seems like a lot of work just to remove & replace the starter.
Any suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

It will wiggle out for you
It has very limited space although they do come out
Take your time twisting it and moving it up and down to remove it
Take note what position it was upon removing to install the new one back in

Posted on May 30, 2010

  • dan langlois Feb 18, 2012

    there are 5 bolts holding up a shroud take them off and the starter will fall out

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to change out a starter


Dis connect the battery, Locate it on the transmission, then dis connect the cables going to it, then loosen and take out the bolts holding it up. Piece of cake

Nov 23, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How do you remove the starter from a 1991 nissan pic up with 2.9 cc engine


I did not find the instructions for a 2.9 L engine per se, but the following should be good for many American models of the 1991 Nissan d21 Pickup truck: REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter. Fig. 1: Starter removal on 4WD - 6-cylinder engine 86713015.gif
    Fig. 2: Starter removal on 2WD - 6-cylinder engine 86713016.gif

  2. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter. CAUTION
      The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
    4. Remove the exhaust manifold heat insulator.
    5. Remove the fuel tube retainer bolt.
  3. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.
  4. Unfasten the remaining electrical connections at the starter solenoid.
  5. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out. To install:
  6. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  7. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  8. Install all remaining components in reverse order of removal.
  9. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.
prev.gif next.gif

Oct 07, 2010 | 1991 Nissan Pickup

1 Answer

Can't get the starter out of a 1991 Nissan pickup.


The second bolt is hidden way up and tucked in near the solenoid. You need to setup a ratchet with extensions/socket (14mm) combination that is just a little longer than the starter motor. If you just can't picture where the bolt is, then go down to the parts store and look at/purchase the replacement starter to see how it mounts up.
There are two bolts for the starter mount and one nut for the main starter power lead. There is one plug for the starter key switch.
Disconnect plug. Loosen lower bolt. Remover upper bolt. Remove lower bolt. Twist starter so you can remove main power cable nut (be sure to have disconnected the battery first!) Pull starter.

Apr 18, 2009 | 1991 Nissan Pickup

1 Answer

1992 toyota pickup need to change the cluch. is there a easy way to do this.???


no easy way.you will need a jack and stands metric tools disconeck batery remove starter and drive line remove shifter ther are 6 bolts you can axis them from the inside of truck by removeing the shifter boot.place a jack under the trasmition remove the trasmition mount and then remove the 6 bellhouseing bolts 14.mmbut first disconeckall wires from the tansmition after all this is you may need help to lower the trans.6 12mm bolts hold the cluch inplace remove and replace cluch.repet proses should take 3hrs to do this

Apr 16, 2009 | 1992 Toyota Pickup

2 Answers

Chevy S10 Pickup Starter. Removed the two bolts


Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Mar 14, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

How do i remove the transmission off a 1991 isuzu pickup?


put truck on jack stands disconect batt . remove driveshaft/ starter .torqconverter bolts if automatic. if standerd slave cyl .shifter linkage .when all ***** are out of your way remove crossmember under trans . if 6 cyl dont let distributor hit firewall remove bellhousing bolts trans should fall out ..... support trans with jack .....dont get under trans it is heavey!!!!!!!!!!!!!!

Mar 05, 2009 | 1991 Isuzu Pickup

2 Answers

Changing starter on GMC sierra diesel


Yes...this has a suppot on the front of the starter with a 7/16 nut

Nov 12, 2008 | 2000 GMC New Sierra 1500

2 Answers

Remove and replace 1994 Toyota pickup starter


disconnect battery ..remove skid plate..remove battery/ignition wire from starter (2 nuts)..remove starter bolts(2 )

Nov 07, 2008 | 1994 Toyota Pickup

Not finding what you are looking for?
1991 Chevrolet S-10 Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...