Question about 1995 Chevrolet G20

1 Answer

Does not seem to be running on all cylinders- running rough- stalling. replaced plugs- no improvement

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 288 Answers

Ohm test all plugg wires and check distbutor bushing for looseness on top of rotor also you can do clynder test with engine runnig remove one spark plug wire at a time with well insulated pliers at the distrubutor cap and see what cylinder is not firing if all have same drop then its something else

Posted on May 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What cylinder is the # 1 cylinder on a 1998 volvo 5 cylinder


You can not check the timing with a timing light. IPD has a Code Reader that will give a running diagnostic that includes Timing for $80 search ipdusa.

Jan 07, 2013 | 1998 Volvo S70

1 Answer

99 mpv missfires,splutters.wont idle & has no power. when MAF is disconnected runs a lot better. I replaced the Maf but still does the same.The problem started suddenly,drove to work ok but when i


replace fuel filter, clean fuel injectors.could have bad fuel, do a code scan before buying new parts.faulty egr valve or faulty engine coolant temperature sensor cause engine run poorly.replace spark plugs and wires because if spark plug wires is bad or spark plug and ignition coil is bad that will cause rough idling misfiring and stalling you have dead cylinder not firing properly..

Oct 01, 2012 | Cars & Trucks

1 Answer

I have a 1990 dodge dakota 3.9 liter v6...idles rough and stalls out at stopping...i have changed cap rotor plugs and wires...and also the throttle positioning sensor...no change..any ideas would be...


Do the service below.

Engine stalling and rough run issue at low speeds

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control. If this doesn't improve the problem you have mechanical problems in the engine like a low cylinder die to worn rings or leaking valve seats.



Jun 23, 2012 | 1990 Dodge Dakota

1 Answer

Car intermittently idles rough and sometimes seems as though it wants to stall..had a scan done when check engine light came on..said misfire on cylinder 2..spark pllugs replaced but problem still per


This is most likely your problem, cheap fix. DIY. Take off the plastic cover from the top if your engine. There are two coils each with a plug wire connecting to the cylinder beside it. Replace the coil that the code came from. Its pretty easy and you can get the part for about 40 bucks online. Email me at joeyc507@yahoo.com with any questions.

Jun 02, 2012 | Hyundai Motor 2004 Sonata

1 Answer

Can a bad intake gasket cause my car not to run or run rough


Yes. If it is leaking, the engine is not getting enough air intake. It's the same as disconnecting the PCV valve.

Apr 29, 2012 | 1996 Oldsmobile Cutlass Ciera

1 Answer

After driving for while it starts to run rough and like its going to stall. It looses power and seems to be running on 3 cylinders. Replaced leads and plugs. Suspect injectors.


Put higher octane fuel in to fill and injector cleaner bottle full. Take car on freeway give it a blast ( don't break speed limit but rev engine maybe in lower gear ) and it will run like new. If problem continues after this then diagnostics at dealership next best option.

Oct 21, 2009 | 1999 Daewoo Lanos

1 Answer

Engine running rough!!!!!


check angine presure, check vuccum hoses, spark plugs, fuel injectors

Oct 14, 2009 | Cars & Trucks

2 Answers

2001 isuzu rodeo v6 rough starting


Intake gaskets maybe leaking.

Jun 23, 2009 | 2001 Isuzu Rodeo

1 Answer

93 chev silverodo missing on 2 cylinders


This could be a few things. The first thing i would check is the firing order as 2 crossed leads will cause this . If this checks out ok try a compression test. A blown head gasket between 2 cylinders will also cause this. Hope ive helped

Jan 13, 2009 | 1994 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...