Question about 1998 Chevrolet S-10 Pickup

2 Answers

Ignition switch is in the on position and is stuck, cannot turn off the car, what can i do???? chevy s-10 p/u

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 4,514 Answers

Pull center distributer wire without gettin shocked or disconnect inline fuse in batt area--then u need to buy a haynes manual and troublshoot that switch

Posted on May 30, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 288 Answers

At the bottom side of steering column under the key lock theres a small hole in the plastic cover use a small screw driver and push up on small rod that will let you turn the key off if this vehice has floor shift it may have a broken wire at the shift lever switch at the base of the shifter

Posted on May 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 chevy corsica key stuck in the run position


ignition switch keylock cylinder is broken.

Apr 17, 2013 | 1988 Chevrolet Corsica

1 Answer

I have a chevy impala 2001,i took it to the chevy house and they ran a dynostic and they told me it needed the ignition control module and the ignition swith,so i replaced them both but the car shows to be...


try this install the new key in the ignition switch. turn on the ignition switch to the on position for 10 minutes.when the system led lock light disappear.turn off the ignition switch for 5 seconds.then start the engine.still dont start.try this procedure few more times.if car still dont crank and you see the pad lock symbols.the dealership will have to reprogram the new key and body control module.

Apr 15, 2011 | 2003 Chevrolet Impala

1 Answer

How do i program a keyless remote for a chevy 2002 S10?


1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.

Mar 05, 2010 | 2002 Chevrolet S-10

1 Answer

Battery went dead in 2007 Chevy Silverado truck. Now, remote does not work. Replaced battery in remote and it still does not work.


Make sure you have one working ignition key and all remotes for the vehicle.

1) Close all vehicle doors.
2) Insert the key into the ignition.
3) Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
4) Perform steps 5 through 8 in fairly rapid succession.
5) Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6) Turn the ignition switch to the OFF position.
7) Turn the ignition switch to the ON position.
8) Turn the ignition switch to the OFF position.
9) Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10) Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11) Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
12) Turn the ignition switch OFF then to the ON position in order to exit the transmitter programming mode.

Feb 28, 2010 | 2007 Chevrolet Silverado 1500 2WD

3 Answers

Replaced ignition switch 2003 chevy impala and car will not start


After you replace the ignition switch turn the key to start the car and release leave the key were it stops after trying to start wait 10 minutes until security light goes out turn key to full off position then repeat the above procedure two more times for a total of three on the 3rd attempt to start car wait for light to go out then turn key to full off positoion wait 10 seconds then try to start car body control module should learn new pass code and the car should start.
Big john, J@J Automotive

Sep 15, 2009 | 1999 Chevrolet Lumina

3 Answers

2005 Chevy Impala ignition switch stuck in off position


Someone may have tried to steal the car and damaged the lock's internal pins. Replace the entire lock with new.

Sep 08, 2009 | 2005 Chevrolet Impala

1 Answer

Keyless entry wont work 2002 chevy s10 LS


try this procedure to reporgram:

1. Close all vehicle doors.

2. Insert the key into the ignition.

3. Hold down the power UNLOCK button on the driver's continue to hold down until instructed
to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.

5. Turn the key to the ON position (as far as you can go without starting the engine).

6. Turn the ignition switch to the OFF position.

7. Turn the ignition switch to the ON position.

8. Turn the ignition switch to the OFF position.

9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the vehicle locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode

Jun 30, 2009 | 2002 Chevrolet S-10

1 Answer

Program a new key fob for a 2002 chevy tahoe


1. Close all vehicle doors.



2. Insert the key into the ignition.


3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.



4. Perform steps 5 through 8 in fairly rapid succession.


5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).



6. Turn the ignition switch to the OFF position.


7. Turn the ignition switch to the ON position.


8. Turn the ignition switch to the OFF position.


9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.



10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.



11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).



12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.




Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 27, 2009 | 2001 Chevrolet Blazer

1 Answer

Need the procedure to program my new remote...THANKS!!!


1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.

May 20, 2009 | 2005 Chevrolet Silverado

1 Answer

Reprograming a keyless remote


program transmitter code(s) as follows:
1) Confirm that all the doors are closed and the ignition key is out of the ignition cylinder.
2) Open the driver’s door. Insert the key and turn the ignition switch to ON position within 10 seconds.
3) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
4) Push and release the driver’s door switch (1) 3 times within 20 seconds.
5) Insert the ignition key and turn the ignition switch to ON position within 10 seconds.
6) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
7) Press and hold both LOCK and UNLOCK buttons (2) on the transmitter (3) for more than 5 seconds
within 20 seconds of removing the ignition key from the lock cylinder in step 6.
8) Press LOCK or UNLOCK button (2) on the transmitter (3) within 5 seconds (after step 7). All the
doors will lock/ unlock to confirm that this process has been properly done.
With this process, the transmitter has been programmed.
9) If you want to program an additional transmitter, repeat the procedure from Step 1) through Step 8).
10) Make sure that the keyless entry system properly operates by operating each transmitter.

Nov 08, 2008 | 2000 Chevrolet Tracker

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...