Question about 1995 Jeep Grand Cherokee

1 Answer

Took out front driveshaft and it rolls in park does the driveshaft have to be in it on all wheel drive

Posted by on

  • Richard Scordino May 29, 2010

    Depends on which transfer case is in there but I'm pretty sure it shouldn't roll unless the transfer case is in neutral.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 972 Answers

Yes it does

Posted on May 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I Drive my 2000 Mercury Mountaineer all wheel drive 5.0 liter SUV. without the front drive shaft, can I remove it and still drive it for a week or could this damage the transfer case


it is all wheel drive so realistically the answer is ---no
However if you have a center diff lock switch to make it 4wd then --yes -- you can as that will lock up the diff in the transfer case
Will it damage the transfer case ---no--as there is no front drive shaft( you took it out) to cause a torque wind up problem in the drive train
AS to the park selection -- that is a physical connection of a pall in a ring gear in the transmission and the park action would be the same as in a 2wd vehicle
remember that is a requirement by law to engage the park brake and not to rely on the park selection of the transmission

Jan 02, 2016 | Mercury Cars & Trucks

1 Answer

Why does my 4 wheel drive not work all the time?


Elaine,

not work, do tell what makes you think it dont work (a lamp) or tires slipping or dead tires. (by tires mean that and traction)??????????

what mode fails, of the many, and where.???????



first off, we dont know what your tires are touching.

on road, or off road. pavement or ICE or snow.

that matters big time . (you read manual and match MODE to Road)

your lost operators guide explains all that, right?

eg: how and when to use, 4wd, its all there. I promise.

ControlTrac 4-wheel-drive system



here are the mode. which one , gives you problems.



quote ford with comments.



What are the modes, and how do they differ?

(note this is the operational behavior of a 2008 Ford Expedition. Newer and older Expeditions will vary only slightly)



2H 2-wheel-drive with high range gearing (1.00:1) Rear-wheel-drive capability,

2-wheel electronic traction control system is enabled



4A 4-wheel-drive Auto with high range gearing (1.00:1) Full-time all-wheel-drive capability, ((best on pavement or any time)

Electronically adjusted torque split to front & rear wheels, Electronically variable center differential,

Front driveshaft & rear primary driveshaft allowed rotational speed difference,

4-wheel electronic traction control system is enabled



4H 4-wheel-drive with high range gearing (1.00:1) Part-time 4-wheel-drive capability, (not for dry pavement EVER)

Continuous 50/50 torque split to front & rear wheels, Electronically locked center differential,

Front driveshaft & rear primary driveshaft mechanically locked with no rotational speed difference,

4-wheel electronic traction control system is enabled



4L 4-wheel-drive with low range gearing (2.64:1) Part-time 4-wheel-drive capability, (off road usage, mostly)

Continuous 50/50 torque split to front & rear wheels, Electronically locked center differential,

Front driveshaft & rear primary driveshaft mechanically locked with no rotational speed difference,

4-wheel electronic traction control system is enabled, ESC and RSC are disabled



In 4A mode the center differential is electronically-controlled and rear drive wheel bias. The on-board computer monitors for any sign of rear drive wheel slip (loss of traction)

If loss of traction is detected, the center differential is told to send a share of the engine\'s torque to the front drive wheels. It will not let the front driveshaft turn at the same speed as the rear driveshaft.



What about traction management?

1997-2002 model Ford Expeditions offered an optional limited-slip rear differential (LSD). A conventional open rear differential was standard along with the conventional open front differential and the electronic locking center differential.

comment with out LSD, one tire can spin, on say ice.

but the other 3 tires dont, in full time.

Jul 04, 2014 | 2003 Ford Expedition

2 Answers

4 wheel drive not working won't engage front


have you checked the front hubs are engaged or engaging

Jan 20, 2012 | 2000 Isuzu Rodeo

1 Answer

My 1992 wrangler won't roll at all. It starts fine, and stays running but when I try to put it in gear it stalls out. Even in neutral, I can't seem to push it to get it rolling. Any suggestions?


This sounds bad, even in neutral it stalls, you cant even push it. i would start by putting the transfer case selector in neutral and see if it rolls, if this jeep is only two wheel drive then start by jack the front wheels up and do this for the four wheel drive also, this is to see if its in the trany or the wheel, check and see if you can spin the wheels in the front, if this is two wd then if the wheels dont spin then you have a problem with the brakes but what concerns me is that it stalls in neutral, i would have to say the problem is in the trany and if this is a stick shift trany i would say the clutch broke and will not release but when its in neutral it should roll. anyway do the same in the rear wheels, jack them up and see if the wheels move, if they dont then remove the driveshaft at the rearend and then see if the wheels move. if the wheels turn with shaft off then theres a problem with the trany oor transfer case if its 4wd, if its 2wheel drive then its something in the trany, if the wheels dont spin with shaft off then start truck and see if it still stalls but dont let it go into gear with driveshaft off you will not be able to stop driveshaft when disconnected, just see if it stalls in neutral. good luck.

Mar 13, 2011 | 1992 Jeep Wrangler

1 Answer

Transfer case on 2006 F150 will engage but no power to front wheels?


SOUNDS LIKE A BAD HUB TRY THIS TO DIAGNOSE THE PROBLEM

Put the transmission in park, set the parking brake and raise the chassis so one of the front wheels is off the ground while the other is still on the ground. When the transfer case is in two-wheel drive, the hubs should be released allowing the wheels to turn freely when spun by hand. If the axle shaft turns when you spin the wheel, it means the hub has not disengaged.
To check engagement, rotate the axle shaft backwards. This should lock the hub. Try turning the wheel by hand again. The axle shaft should now turn with the wheel if the hub is locked. If the hub fails to lock, the hub will have to be disassembled and inspected or replaced.
To check release, hold the axle shaft steady and rotate the wheel backwards. You should hear a click as the locking mechanism slides back out and disengages the hub. Rotate the wheel forward again and it should turn freely.
Another way to check the hubs is to raise the vehicle on a frame contact lift so all four wheels are off the ground. Then start the engine and place the transfer case in four-wheel drive and the transmission in drive. If the front wheels don't turn, look at the front axle shafts. If both shafts are turning, but one wheel is not, the problem is a bad hub on the wheel that isn't turning. If the front driveshafts are not turning when the transfer case is in four-wheel drive, the problem is inside the differential (broken side gears) or the transfer case (broken chain, shift linkage, etc.). If the driveshaft between the transfer case and differential is turning, the problem is in the differential. If the driveshaft is not turning, the vehicle is going to need repairs to the transfer case.
Hope this helps.

Dec 28, 2010 | 2006 Ford F-150

3 Answers

4wheel drive wont engage


First, start checking the fuses an there is also an electrial activaced switch at the transmission or transfer case that may be bad.

95-96
Your control knob should say 2wd, 4auto, 4low.

First, we need to narrow it down to a transfer case issue, or a front axle issue.
Step 1) Jack up the front end and place it securely on jack stands.
Step 2) Verify that the front driveshaft turns by hand. When turning the front driveshaft by hand, the front wheels may or may not turn. Do not be alarmed if they don't turn. This is normal for your vehicle.
Step 3) Start the vehicle and let it idle. Place your foot firmly on the brakes, place the transmission in NEUTRAL, engage 4low, then place the vehicle back in park. DO NOT ENGAGE ANY GEAR!! The lurch as the transmission engages could cause the vehicle to lurch and potentially fall off the jack stands.**If you can turn the front driveshaft, the transfer case is not locking. This could be due to a mechanical issue with the transfer case itself, or an electrical gremlin with the control system. Start a new thread with the results of your checks, and we'll go from there.
**If the front driveshaft does not turn, the transfer case is locking properly and we need to continue searching.
Step 4) With the front wheels in the air, engine idling in PARK, spin one front wheel. The other wheel should spin the opposite direction. If both wheels spin in opposite directions, then the front axle *should* be properly engaged. Take it for a test drive (after safely lowering it to the ground, of course). If the front wheels do not spin in opposite directions, there is a problem with the front axle. This could be due to a mechanical problem with the diff, or a failure of the center axle disconnect to engage the passenger side axle shaft. Start a new thread with the results of your checks, and we'll go from there.

Troubleshooting the CAD on a 95-96 is a bit more involved than I want to get into here, and the problems can vary widely. This'll get you started.


97-01 4-door and 96-00 Sports
Your control knob should say 4auto, 4high, 4low.
First, we need to narrow it down to a transfer case issue, or a front axle issue.

Step 1) Jack up the front end and place it securely on jack stands.

Step 2) Verify that the front driveshaft turns by hand. When turning the front driveshaft by hand, the front wheels should turn. (If only one turns, don't be alarmed. One wheel sometimes has more resistance in the brakes, bearings, or CV joints. This is normal)
Step 3) Start the vehicle and let it idle in PARK. Engage 4high. DO NOT PUT THE VEHICLE IN GEAR!!! Crawl underneath and see if you can turn the front driveshaft.
**If you can turn the front driveshaft, the transfer case is not locking. This could be due to a mechanical issue with the transfer case itself, or an electrical gremlin with the control system. Start a new thread with the results of your checks, and we'll go from there.
**If the front driveshaft does not turn, the transfer case is locking properly and we need to continue searching.
Step 4) With the front wheels in the air, engine idling in PARK, spin one front wheel. The other wheel should spin the opposite direction. If both wheels spin in opposite directions, then the front axle *should* be properly engaged. Take it for a test drive (after safely lowering it to the ground, of course). If the front wheels do not spin in opposite directions, there is a problem with the front axle. Start a new thread with the results of your checks, and we'll go from there.


'01-'03 Sport and '01-'05 Sport Trac
Your control knob should say 2wd, 4high, 4low

The transfer case in these trucks functions essentially like the 1st-gens' 13-54 t-case. (i.e. it uses a lockup collar engaged by the transfer case shift motor) The troubleshooting procedure is very similar, but you don't need to worry about hubs or center-axle disconnects engaging.

Step 1) Jack up the front end and place it securely on jack stands.
Step 2) Verify that the front driveshaft turns by hand. When turning the front driveshaft by hand, the front wheels should turn. (If only one turns, don't be alarmed. One wheel sometimes has more resistance in the brakes, bearings, or CV joints. This is normal)
Step 3) Start the vehicle and let it idle in PARK. Engage 4high. DO NOT PUT THE VEHICLE IN GEAR!!! Crawl underneath and see if you can turn the front driveshaft.
**If you can turn the front driveshaft, the transfer case is not locking. The shift motor could be falsely reading an incorrect t-case position, or it could be a mechanical issue with the case itself. Start a new thread with the results of your checks, and we'll go from there.
**If the front driveshaft does not turn, the transfer case is locking properly and we need to continue searching.
Step 4) With the front wheels in the air, engine idling in PARK, spin one front wheel. The other wheel should spin the opposite direction. If it does, the system should be properly engaged. Safely lower the vehicle to the ground and take it for a test drive. If the wheels do NOT spin in opposite directions, there is a problem with the front differential or axle. Start a new thread with the results of your checks, and we'll go from there.


Keep us updated.

Dec 16, 2010 | 1996 Ford Explorer

1 Answer

2003 silverado chevvy 2500 HD


Automatic trans? Sounds to me like the trans is either busted up or damaged in such a way that the gearing won't rotate or things are binding internally. With the drive shaft off, transfercase in 2WD, and trans in anything but PARK, the driveshaft should be able to turn by hand. Of, course, a drop of the pan can also give a indication. When gears bust up in a 4L80E, there is evidence.

Apr 07, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

95 blazer 4x4 4 wheel drive not working


There is a vacuum actuator mounted on the front differential that locks the shafts to engage four wheel drive.

Jan 28, 2009 | 1995 Chevrolet Blazer

2 Answers

Transfer case wont engage


shift into 4wd and move truck a couple of feet.
if light is still off, park truck block the wheels set the park brake jack right front wheel and try to hand spin the wheel if wheel doesn't turn 4x4 is functioning properly but there is a wiring problem use an ohmmeter to check the 4x4 switch wiring fuse and bulb
if wheel turns freely the front axle or transfer case is not engaged
attempt to hand spin the front driveshft if the driveshaft will spin the transfer case is not engaged check the transfer case shift linkage, problem is in linkage or transfer case internals
if the driveshaft will not spin the transfer case is engaged properly
with trnsmission in neutral or park start engine measure vacuum on the two vac lines at front axle shift motor . one line should have approx 20" vacuum. other line should have none
if no vacuum measured look for vac leak or bad vac switch
if both lines have vac look for a bad vac swithc or ruptured cad actuator diaphragm
if one line has 20" +- VAC
move transfer case lever to 2wd measure vac again lines should have swapped vac signals
if no vac switch bad or 4wd shift likage needs adjusting
if yes vac motor bad or stuck or shift fork stuck
remove vac shift motor from the axle attach vac lines to shift motor engage disengage 4wd
does shift motor plunger move at least 1/2 inch
no shift motor bad
yes check axle shift fork and vac motor for binging

Jan 27, 2009 | 1999 Dodge Ram

1 Answer

Front driveshaft...


yes you just won't have 4 wheel drive

Jan 12, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...