Question about 2002 Kia Sedona

1 Answer

How do I remove the hald shaft from the transmission?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 972 Answers

You have to pry it out with pry bar that will fit between it and the trans.it is tough to get them loose for first time

Posted on May 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace a transmission control solenoid and where is it located?


Which control solenoid ? There are a few ,1-2 shift , TCC solenoid ,3-4 shift ,PWM solenoid .
Remove the case side cover. Refer to Case Side Cover Replacement (W/ Gasket) .
Removal Procedure
Tools Required J 28467-360 Engine Support Fixture
  1. Disconnect the negative battery cable. Refer to
  2. Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
    in General Information.
  3. Remove the park/neutral position switch. Refer to PNP Switch Replacement
  4. Install the J 28467-360
  5. Raise the vehicle. Support the vehicle. Refer to Vehicle Lifting and Jacking in General Information.
  6. Remove the left front tire and wheel assembly. Refer to Wheel Removal in Suspension.
  7. Remove the inner splash shield.
  8. Remove the tie rod end from the knuckle assembly. Refer to Strut Assembly in Suspension.
  9. Remove the stabilizer shaft link from the lower control arm. Refer to Control Arm in Suspension.
  10. Remove the ball joint from the steering knuckle. Refer to Ball Joint in Suspension.
  11. Remove the drive axle from the transmission. Refer to Drive Axle in Driveline/Axle.
  12. Remove the pinch bolt from the steering gear intermediate shaft. Refer to Intermediate Steering Shaft in Suspension.
  13. Caution: Failure to disconnect the intermediate shaft from the rack and pinion steering gear stub shaft can result in damage to the steering gear or to the intermediate shaft. This damage may cause loss of steering control, which could result in an accident and possible personal injury.
  14. Remove the intermediate shaft from the steering gear. Refer to Intermediate Steering Shaft in Suspension.
  15. Position a transmission jack under the transmission oil pan. Raise the jack until lit supports the transmission.
  16. Remove the three frame-to-body bolts on the left side.
  17. Lower the transmission jack and the transmission in order to gain access to the case side cover.
  18. Remove the oil cooler pipes at the case. Refer to Automatic Transmission Oil Cooler Pipes Replacement
This is a monumental task , suggest you take your vehicle to AAMCO or some other transmission shop .

May 09, 2016 | 1996 Oldsmobile 88

1 Answer

Manual transmission fluid leak from the input for cv drive shaftdriver side


Well, not being familiar with your vehicle I can recommend this. The shaft seal is seated in the transmission where the input shaft enters the transmission.

If the seal part is a round metal ring with a rubber inner seal, then in all likelyhood it is pressed into the transmission.

Now if you think you can pull the seal out after you remove the CV drive shaft - meaning do you have enough room to get up in there to pop it out, then yes you can do it without removing the transmission.

On the other hand if the seal is not accessable to pop out then you will probablly have to remove the transmission which is by no means an easy job. Might want to take a look on youtube and do a search for CV inner shaft seal removal for your particular vehicle or one similar. You will probably find the answer there.

Hope this info helps.

Feb 13, 2015 | Cars & Trucks

1 Answer

How is the easiest way to repair the speedo drive worm gear on a Holden Trimatic transmission, it is loose and sliding along the shaft. Box is still in car and this observation is from the speedo cable...


remove the rear extension housing of the transmission( remove tail shaft and rear cross member--transmission pan on jack) the drive hear is held in place by a small spring clip that fits under the gear on the shaft. The drive is by a small ball bearing in the hole in the shaft
If the gear is damaged you should be able to pull it back off the output shaft of the transmission.
watch for transmission oil coming out when you remove the extension housing.

Feb 09, 2015 | Holden Cars & Trucks

2 Answers

Transmission rear seal instalation


remove the drive shaft ( tail shaft) lever out the old seal. put sealer around new seal and fit back in extension housing. Use something that is the same size as the outer edge of the seal and tap it in flush with the edge of the transmission housing. Expect some oil to drain out when the tail shaft and seal is removed

Dec 25, 2014 | 1997 Chevrolet Blazer

1 Answer

How to remove1995 cavalier transmission


The transmission is transversely mounted in these vehicles. The mount that secures the transmission to the body is also supporting the engine. If you want to remove the transmission without also removing the engine you will have to support the engine once you remove the transmission mount. You will need to remove the drivers side wheel, caliper, and rotor. You then need to remove the drivers side CV shaft. You will need to separate the lower ball joint in order to remove the shaft and to provide working room to separate the transmission from the engine. You need to disconnect the Shift cable (automatic) or slave cylinder (manual) from the transmission. You must separate the passengers side CV shaft from the transmission, but you do not need to full y remove it. Ensure that you do not separate the inner CV joint when pulling the transmission free from the inner splines. Remove the flywheel shield plate. If automatic transmission, unbolt the torque converter from the flywheel. Disconnect any electrical connections from the transmission. If automatic transmission, disconnect the hydraulic lines running to the radiator. Unbolt the transmission from the engine at the bell housing. Automatic transmissions will come out fairly easy...manuals you must pull back to disengage the transmission splines from the clutch disc.

Sep 07, 2014 | Cars & Trucks

2 Answers

Need to replace a seal on transmission for a subaru legacy 1991 do i need to remove the whole transmission


are u talking about the front main seal? if so ,yes u have to take the trans. out to replace

Sep 06, 2012 | 1991 Subaru Legacy

1 Answer

How do I remove automatic transmission from 1993 Chev 2500 pickup?


TRANSMISSION REMOVAL IN STEPS.
The Drive Shaft
  • Using a 1/2-to-2-ton floor jack, lift the front of the truck and place jack stands under the frame. Once the truck is lifted enough for you to safely move around under it, begin removing the four bolts connecting the U-joint between the drive shaft and the rear axle. When you pull the drive shaft out of the tail shaft, transmission fluid will pour out of the tail shaft, so place a drip pan or oil-changing pan under the tail shaft of the transmission.
Lines And Linkage
  • If the truck is an automatic, you will need to remove two transmission lines from the passenger side of the transmission by the bell housing close to the transmission dip stick. If it's a manual transmission you won't have those lines, but you will have shifting linkage on the driver's side of the transmission. Depending on the year of the truck, the linkage is held on by either a cotter pin or locking-sleeve washer. You will also need to remove the speedometer cable. If it's an older truck, it will be a hard-cased cable similar to the emergency brake cable that threads onto the driver side of the transmission just before the bell housing. If the truck is a newer model, it will be an electrical set of wires attached to a plug on the tail shaft.

Remove From Engine
  • Remove the transmission mount bolt that holds the tail end of the transmission to the cross member on the frame. You will need to either use wood blocks or a jack to support the weight of the transmission. Take out the nine bolts on the bell housing that attach the transmission to the engine--there is one on the top center of the bell housing, two along each side of the bell housing and two on each side at the bottom next to the guide pins.
Remove From Vehicle
  • Once removed, maneuver the transmission to the rear of the truck about 6 inches until it clears either the clutch kit of a manual or the torque converter of an automatic. When the transmission is free, lower the bell housing end of the transmission down until the tail shaft is clear of the cross member.

Aug 31, 2012 | Cars & Trucks

1 Answer

I NEED THE STEPS OF TAKING OUT A TRANSMISSION OUT OF MY 1994 HONDA ACCORD


  1. Remove the hub cap and bolt the wheel back in.
  2. Punch out the spindle nut lock and loosen the spindle nut.
  3. Raise and support the vehicle and block the rear tires.
  4. Remove the wheel.
  5. Drain the transmission.
  6. Remove the all the damper fork nuts and all the brake hose nuts on the damper fork and on the shock absorber.
  7. Remove the damper fork.
  8. Remove the driver side and passenger side front suspension flange nut inside the engine bay and slide the upper arm out
  9. Turn the steering wheel all the way to the passenger side and remove the passenger drive shaft spline from the hub.
  10. Separate the inner driveshaft from the transmission with a large screw driver (or crow bar).
  11. Remove the passenger side drive shaft. Do not pull.
  12. Remove the front radius rod.

Under the car.

  1. Remove the center beam.
  2. Remove the torque converter cover, the control cable holder and remove shift control cable.
  3. Remove the drive plate bolts and four transmission housing bolts.

Inside the engine bay.

  1. Place a transmission jack or several small jacks under the transmission.
  2. Disconnect all the electrical connectors.
  3. Remove the speed sensor gear shaft but leave the hoses on.
  4. Remove the distributor and mark the distributor shaft with a razor or a diamond etcher, usually on the head side or both.
  5. Remove the throttle control lever cable.
  6. Remove the transmission cooler hoses mounting bolts and their 4 washers.
  7. Remove the starter.
  8. Remove the all the transmission housing bolts.
  9. If the transmission won't come out remove a horizontal side engine mounting bolt and raise oil pan (with a wooden block between the oil pan and jack) until the transmission clears.
  10. Lower the transmission into the transmission jack.
  11. With the driver side front suspension flange out of the way, turn the steering towards the right then remove the driver side inner drive shaft with a large flathead screw driver.
  12. Lower the low profile transmission jack and slide the transmission and the jack from under the car. Don't loose the two dowel pins.
  13. Block all transmission fluid ports from leakage and dust and dirt.
  14. If repairs are being done repair the transmission in a dust, sand free environment.

Jul 30, 2011 | Honda Accord Cars & Trucks

1 Answer

How to repair cluch disc suzuki mini truck


The clutch is a friction disk up against the flywheel and pressed against it by the clutch pressure place. So you have to remove the transmission in order to gain access.
For that you:
disconnect battery
drop drive shaft
remove speedometer cable or wire, shift and clutch linkage
support engine and transmission separately.
remove rear support
remove engine to transmission bolts, cover plate, and starter
slide transmission back until input shaft clears clutch pressure plate ring
lower transmission.
remove pressure plate evenly and slowly

Then you inspect for wear on the pilot bushing the input shaft rests on, the friction disc is assumed to be too thin, the pressure plate should not show heat damage or scratching, and the throw out bearing should not be noisy.

Installation is reverse except you use a fake plastic input shaft in order to firmly locate the friction disk in the right place, when bolting pressure plate on. Remember to tighten evenly, diagonally, and not to break off any bolts by over tightening. Remove fake plastic input shaft before continuing then.

Dec 04, 2010 | Suzuki Sidekick Cars & Trucks

1 Answer

How do you remove the front drive shaft in a 1999 Chevy 1/2 ton 4X4?


Jack up front end, and put on stands. Remove wheel. Remove large nut on end of drive shaft. Remove lower control arm, from wheel hub bearing assm.
Push drive shaft back toward transmission.
Now that drive shaft is free, you must "pop" it out of transmission output.
You can use a pry bar, but be careful not to damage anything.

Apr 15, 2010 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
2002 Kia Sedona Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...