Question about 1998 Ford F150 Regular Cab

Open Question

What size nut is on the power steering gear box?

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 111 Answers

SOURCE: power steering gear box leaking at steering column to gear box

I just found 1 of my power steering leaks in my 1990 toy pickup. My high pressure line has a hole in it. I used a florecent die kit to locate the leak. You can get it at Autozone. 

Posted on Feb 02, 2009

Monster80
  • 460 Answers

SOURCE: How to remove the rack and pinion on 95 grand am

To make it easier to remove, Place a jack at the rear of the of the sub frame.Remove the rear bolts which there are usually 2 on each side or more.Next make sure the car is high enough off the ground loosen the front bolts.DO NOT REMOVE!!!!!!!After you have done that slowly let down on the jack.Just enough to pull the rack out..Lowering the jack to far could break some stuff so be careful and go slow..

Posted on Mar 29, 2009

  • 91 Answers

SOURCE: power steering leak on a 1988 full size bronco

The gear box is a common problem on this model. That would be the place I would start. A cheap, temporary fix is to go to your local parts store and ask for Lucas Power Steering Stop-Leak. It will buy you some time.

Posted on Apr 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need a tool screws threat size which is used for pull and installing power steering pump pulley for 1997 zj grand cherokee


If you buy a new power steering pump, it usually comes with a nut,bolt and washer to install the pulley. The removal tool can be purchased and possibly rented at any parte store

Apr 14, 2015 | 1997 Jeep Grand Cherokee

1 Answer

How to fix a rattle in my steering on my 1999 gmc jimmy. i have a rattle in my steering in my 1999 gmc jimmy


Check the steering intermediate shaft connection to the steering gear box, its slip shaft and the connection to the stering collumn. if those are ok, its probably slop in the steering gear box. Some of that can be adjusted out on the gear box by your mechanic. You will see either a flat head cut or hex head inset with a lock nut on the top of the gear box. Loosening hte lock nut and tightening the bolt to factory torque setting then releasing it the appropriate specified degress will reset the gear box back to factory settings. Beware if you set this wrong you will cause your steering to bind when turning. Therefore only let a qualified mechanic do this for you.

Feb 12, 2013 | 1999 GMC Jimmy

1 Answer

Loose steering gear box needs adjusting


There should be a adjusting screw with a lock nut on it on the steering gear box. With the wheels straight ahead, loosen the lock nut and turn the screw in until it stops the back it out about a 1/8 of a turn. Try the steering check it for binding, it should turn free in both directions. If there is still too much play you can try turning it tighter but make sure it does not bind up. You may have to replace the steering gear box, you can probably get a rebuilt one, or go to; car-parts.com and check the salvage yards in your area for used.

Mar 05, 2010 | 1981 Ford F 100

2 Answers

Can you ajust the gear box on a 1998 chevy blazer 4x4?


There is an allen screw with a lock nut on the top of the gear box. Tighten it a quarter turn at a time and you will feel a difference in the steering. Don't go crazy with it because it's a preload adjustment and you will put too much resistance on it if you go too far. That wears out your power steering pump as well as the gears in the box.

Feb 28, 2010 | 1998 Chevrolet Blazer

1 Answer

Power steering going bad,need info about rackard pinion


you can buy remanufactured at parts store or buy used from car-part.com. page with * is lowest cost.

It's a pretty big job for a novice.

here's 96 taurus steps with 3.8l engine. don't have 94. should be similar

Removal
SPECIAL SERVICE TOOL(S) REQUIRED Tool Number Description T94T-6000-AH Exhaust Connector Holder Tool T57L-500-B Bench Mounted Holding Fixture
  1. Disconnect negative battery cable.
  1. Position steering wheel one-half turn to right and lock wheel.
  1. Position steering column boot out of the way. Remove pinch bolt retaining steering column intermediate shaft coupling to power steering short rack and separate.
  1. Disconnect PCV vent tube and vacuum supply hose from clean air tube. Loosen two hose clamps retaining clean air tube and position out of the way.
  1. Disconnect power steering auxiliary actuator and power steering pressure switch.
  1. Remove two heat shield pushpin retainers from power steering hose bracket and remove heat shield.
  1. Remove one retaining bolt from left turn pressure hose bracket.
  1. Position drain pan under steering gear.
  1. Remove power steering pressure and return hoses from fittings on power steering rack. Position both hoses out of the way. Disconnect rear HO2S connector at steering rack and position out of the way.
  1. Partially raise vehicle.
  1. Remove front wheel and tire assemblies.
  1. Remove LH upper stabilizer bar link retaining nut and position link out of the way.
  1. Loosen LH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
  1. Loosen RH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
  1. Raise vehicle.
  1. Remove drain pan.
  1. Remove two steering gear retaining nuts at front subframe.
  1. Install Exhaust Connector Holder Tool T94T-6000-AH on flex tube.
  1. Remove bolts, nuts, and gasket from where flex tube and converter Y-pipe connect. Separate tube from pipe.
  1. Position Rotunda Power Train Lift 014-00765 or equivalent with wood blocks approximately 1016 mm (40 inches) in length (secured to lift) under subframe and raise.
  1. Remove two rear subframe retaining bolts and lower subframe approximately 102 mm (4 inches).
  1. Rotate power steering rack to clear bolts from subframe and remove assembly through LH wheel well.
  1. Remove two bolts retaining power steering hose bracket to short rack and remove bracket.
  1. Mount steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
  1. Remove four clamps retaining bellows to steering gear and tie-rods. Remove bellows and power steering gear rack tube.
  1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while loosening inner tie-rods. Remove tie-rods from steering rack. Remove steering rack from bench-mounted holding fixture.
Installation
  1. Mount new steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
  1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while tightening inner tie-rods. Tighten to 90-110 Nm (66-81 lb-ft).
  1. Apply Steering Gear Grease C3AZ-19518-A meeting Ford specification ESB-M1C119-A to groove in connecting rods where tie-rod bellows clamp to front wheel spindle tie-rod and uniformly apply to inner diameter of bellows. Install bellows and gear rack tube onto short rack.
  1. Install new inner and outer bellows clamps.
  1. Remove steering gear from Bench Mounted Holding Fixture and place on bench.
  1. Install power steering hose bracket and retaining bolts at top of steering gear. Tighten to 9-12 Nm (80-106 lb-in).
  1. Install steering gear retaining bolts in steering gear housing and install short rack through LH wheel well.
  1. Position steering rack and retaining bolts through subframe. Raise powertrain lift until rear subframe contacts body and install retaining bolts. Tighten to 135-195 Nm (100-144 lb-ft). Lower and remove powertrain lift from vehicle.
  1. Install power steering short rack-to-subframe nuts. Tighten to 97-132 Nm (72-97 lb-ft).
  1. Install new gasket, bolts and nuts at converter Y-pipe and flex tube. Tighten to 34-46 Nm (26-34 lb-ft).
  1. Remove flex tube holder.
  1. Partially lower vehicle.
  1. Install LH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
  1. Install LH stabilizer bar link and retaining nut. Tighten to 76.5-103.5 Nm (57-76 lb-ft).
  1. Install RH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
  1. Install tire and wheel assemblies. Tighten to 115-142 Nm (85-105 lb-ft).
  1. Lower vehicle.
  1. Remove old Teflon® O-rings from pressure and return hoses. Install new Teflon® O-rings on pressure and return hoses.
  1. Install power steering pressure hose and return hose to fittings on power steering short rack. Tighten to 33-41 Nm (24-30 lb-ft).
  1. Install one retaining bolt to left-turn pressure hose bracket. Tighten to 9-12 Nm (80-106 lb-in).
  1. Connect rear HO2S connectors, power steering auxiliary actuator, and power steering pressure switch electrical connectors.
  1. Position heat shield at power steering hose bracket and install pushpin retainers.
  1. Install clean air tube, connect PCV vent tube and vacuum supply hose, and tighten hose clamps. Tighten to 2-3 Nm (18-27 lb-in).
  1. Install steering column intermediate shaft coupling to power steering short rack and install pinch bolt. Tighten to 41-51 Nm (30-38 lb-ft). Position steering column boot over steering rack.
  1. Fill and purge system.
  1. Check operation.
  1. Adjust only toe for alignment. Refer to Section 04-00 .

Aug 05, 2009 | 1994 Ford Taurus

1 Answer

How to change the power steering on 96 ford explorer


Section 11-02C: Steering Gear, Power Rack and Pinion, Explorer 1996 Explorer with Power Rack and Pinion Steering Workshop Manual REMOVAL AND INSTALLATION Steering Gear SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Pitman Arm Puller T64P-3590-F
Removal
  1. Start engine.
  1. Rotate steering wheel from lock-to-lock (entire gear travel). Record n umber of rotations.
  1. Divide the number of rotations by two. This gives the required number of turns to place system in the on-center position.
  1. NOTE: Verify the front wheels and steering wheel are in the straight-ahead position.

    From the lock position, rotate steering wheel the number of turns determined in Step 3. This places the gear in the on-center position.


    Steering Gear, Explorer




  1. NOTE: Do not rotate steering column when intermediate shaft is disconnected or DAMAGE TO CLOCKSPRING will result.

    Remove bolt retaining the lower steering column shaft to the steering gear input shaft.




  1. Disconnect the lower steering column shaft from the steering gear.
  1. Remove stabilizer bar attachment from frame for clearance to remove gear.
  1. Unscrew the quick connect fittings for the power steering pressure hose (3A719) and power steering return hoses (3A713) at the steering gear housing (3548).


    Power Steering Hose Connections





    Item Part Number Description 1 3A674 Power Steering Pump 2 3A719 Power Steering Pressure Hose 3 3F780 Power Steering Cooler and Hose Assembly 4 3504 Steering Gear 5 5005 Frame
  1. Plug ends of fluid lines removed and ports in gear to prevent damage and entry of dirt.
  1. Remove two (2) nuts from P/S cooler.
  1. Remove P/S cooler from vehicle.
  1. Remove and discard the cotter pin retaining the nut to tie rod end (3A130) and remove nut.
  1. Separate tie rod ends from front wheel spindle (3105) using Pitman Arm Puller T64P-3590-F.




  1. Remove the two nuts, bolts, and washer assemblies retaining steering gear (3504) to front crossmember (5019).
  1. Remove steering gear from vehicle. If required, remove steering gear mounting bracket housing insulators (3F640) and steering gear insulators (3C716) from steering gear housing.





    Item Part Number Description 1 N807881-S60 Bolt 2 385935-S36 Washer 3 3F640 Steering Gear Mounting Housing Insulator 4 3504 Steering Gear 5 N800255-S60 Nut 6 5019 Front Crossmember 7 3C716 Steering Gear Insulator
Installation
  1. If removed, install steering gear mounting insulators into the steering gear housing.
  1. Push the steering gear mounting insulator and steering gear insulator in until there is no space between the lip on the insulator and steering gear housing.
  1. Position steering gear on front crossmember. Install nuts, bolts and washers retaining steering gear to front crossmember. Tighten to 128-172 Nm (94-127 lb-ft).
  1. Position power steering cooler onto bolts and install nuts. Tighten nuts to 68-92 Nm (50-68 lb-ft).
  1. NOTE: The fittings design allows the power steering pressure hose and power steering return hose to swivel when properly tightened. Do not attempt to eliminate looseness by overtightening, since this can cause damage to fittings.

    Connect power steering pressure hose and power steering return hose to appropriate ports on steering gear housing. Tighten fittings to 27-34 Nm (20-25 lb-ft).
  1. NOTE: Make sure the tie rod ends (3A131) are seated in the tapered spindle holes to prevent rotation while tightening nut.

    With the steering gear, steering wheel (3600) and wheel (1007) in the on-center position, attach the tie rod end to front wheel spindle and tighten to 56-76 Nm (77-103 lb-ft).
  1. If necessary, advance tie rod nuts to the next slot. Install cotter pins.
  1. NOTE: Verify that no rotation from the on-center position has occurred.

    Position steering column lower intermediate shaft over steering gear input shaft. Outer input shaft dust shield must be in place. Replace pinch bolt and tighten to 41-56 Nm (30-42 lb-ft).
  1. Replace the front wheel and tire assemblies. Refer to Section 04-04 .
  1. Replace wheel covers.
  1. Lower vehicle.
  1. Refill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F.
  1. Purge air from steering system. Refer to Section 11-00 . Verify absence of any unusual power steering noise.
  1. Check and adjust toe alignment specifications. Refer to Section 04-00 .
  1. Make sure steering gear operates correctly and is not leaking.
  1. Check and adjust fluid level in power steering oil reservoir.

Jul 10, 2009 | 1998 Mercury Villager

1 Answer

Excessive play in steering


There should be a bolt sticking out of the steering box with 1 or 2 nuts on the bolt. This is a thrust setting which puts load on the steering gear. Most people jack the front wheels off the ground and then back off the nut or nuts. You then turn the bolt to screw further into the steering box until you have 1/2 inch or less of play in the steering wheel. Then tighten the nut or nuts down and recheck to see if setting held.

Jun 18, 2009 | 1981 Ford F 100

2 Answers

Steering box adjustment, how


Before you do this procedure, check the rubber or universal joint connector between steering column and the steering gear. If it's worn it will cause looseness and there's your problem. Otherwise, there is a threaded screw with a lock nut on the top of steering gear. Clean threads first. Put a large flat screwdriver on the screw and loosen the lock nut. Back it off several turns. Now, screw the screw down into the gear box. Not too tight though. Your actually jamming the gears back together. Back it off a 1/2 turn or so and run it back in lightly. Hold the screwdriver and tighten the lock nut. This is usually effective.

Apr 21, 2009 | Chevrolet Astro Cars & Trucks

1 Answer

Far to much steering wheel play befor tire reaction


Loosen nut on top of steering gear box. Tighten adjustment bolt 1/4 turn at a time then tighten nut. Drive and see if it hold together better. Repeat until you can't tighten adjustment bolt any more. If it's still iffy, replace your steering gear box.

Apr 11, 2009 | 1997 Jeep Tj

Not finding what you are looking for?
1998 Ford F150 Regular Cab Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...