Question about 2007 Mazda B2300

1 Answer

2008 b2300-fan only blows onto windshield ,other switch positions just the same.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 22 Answers

Try changing the switch.

Posted on May 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

Is there a fuse for windshield wiper pump in 2008 Ford Ege


Maybe, but more likely a connection or the pump itself, especially if it froze with plain water instead of wiper fluid. Try to check pump by a tempory jumper to the positive side of the pump from the positive battery terminal. If pump good track wire back to washer switch. If wire is all good, may be switch or connections.

Mar 12, 2015 | 2008 Ford Edge

1 Answer

A/C climate control in car will constantly blow on the windshield instead of at occupants.


It will not be the ac as it is cooling
It will be a problem climate control module and vent control system.
might be a vacuum hose that was disturbed during the hose replacement.

Mar 08, 2015 | Cars & Trucks

1 Answer

Why my A/C condenser fan won t stop running, dodge ram 2008


To clarify, the compressor and fan will run in defrost mode. The compressor and fan runs to dry out the air blowing onto the windshield.
Now if the condenser fan runs in "heat" you may have a problem with the fan relay or the main controller.

Sep 25, 2014 | 2008 Dodge Ram Pickup 1500

1 Answer

Engine and AC fans start spinning


If that is the same thing as Defrost, the compressor will run even if the ac button is off. The compressor runs to dry the air blowing on the windshield.

Aug 04, 2014 | 2005 Hyundai Santa Fe

1 Answer

I have a 2001 9-5 SE V6 with about 88.5K miles. The interior fan air only blows out of the face/dash vents no matter what position (feet, windshield, or face) the indicator shows. Fan speed and temp work...


2 possible problems, #1 is the control switch on the dash has malfuntioned(less likely) , #2 is the motor under the dash that changes the blower position is not working properly.

Please rate my answer ............Thanks

Dec 02, 2010 | 1999 Saab 9-5

2 Answers

I have 2008 uplander ls the problem is a flim gets on the inside of winshield. very light but anoying


Is the heater core slowly leaking antifreeze? Do you smell any sweet smelling antifreeze smell associated with a leak?

Or, do you drive through a lot of construction zones that blow contaminated air onto the windshield?

Oct 29, 2010 | 2008 Chevrolet Uplander

1 Answer

I have a 2008 Grand Prix. Windshield washer is


follow the hoses to the hood or wiper arm (i dont know where your spray nozzles are)and disconnect hem and press the spray button. if it sprays your nozzles are plugged, if not its your pump motor.

Feb 16, 2010 | 2008 Pontiac Grand Prix

1 Answer

I have a dodge 600. when the heater is switched to defrost no air


check for any vaccum leaks, hoses leaking or unhooked, also may have a bad blend door motor. see if all other positions work like floor, vents, fresh air and recycle air. good luck.

Oct 14, 2009 | 1988 Dodge 600

2 Answers

Climate Control malfunction


Sounds like a bad fan speed switch.

Apr 13, 2017 | 2006 Dodge Charger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...