Question about 2006 Toyota Corolla

1 Answer

ECM CLEAR CHECK ENGINE LIGHT

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 154 Answers

TRY DISCOONECTING BATTERY FOR 1 MINUTE,, IF NOT YOU WILL NEED A SCANNER TO DO IT..

Posted on May 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car Toyota gaia has an engine check light on and after diagnosis it gives C1201 code. How do l clear this?


Engine control system fault in the brake system
To clear it fix the braking system
Repair or replace harness and connector
Or replace ecm

Oct 29, 2016 | Toyota Cars & Trucks

1 Answer

My T600 has a n-14 cummins engine in it and I can't reset the check engine light


yellow check engine light ' TruckersReport.com Trucking Forum ' #1 ...

www.thetruckersreport.com > ... > Trucks [ Eighteen Wheelers ]
Oct 31, 2010 - i had the yellow check engine light turn on when i started my truck. it ...I know the truck I drive has a N14 Plus in it and the other day ... You will clear all stored codes, then start engine and when it stalls pull code with button! Low water warning
May 10, 2015
Kenworth Forum
May 10, 2015
More results from www.thetruckersreport.com

N14 Cummins Engine Video of ECM Sensors - YouTube

? 3:40
https://www.youtube.com/watch?v=ZedwtvXS4s0
Jan 28, 2013 - Uploaded by Terry Chron
Explaining where The Cam Sensor, Turbo Boost Sensor and ECM are Located. For ECMs, Sensor, Wiring .

Nov 19, 2015 | Cars & Trucks

1 Answer

How can i tell if my computer has went bad on my 1997 chevy lumina 3.1?


Patrick, car places refer to the computer as the Engine Control Module, or the ECU.
According to CarsGuru.com: "If you are having a bunch of codes that don't mean anything then you might have an ECM going bad, but first you need to make sure all of the powers and ground paths are clean and tight, then clear the system and run a relearn for the ECM, usually about 20 minutes driving normally will do this, if the check engine turns on again then have the codes read and repost back here for further diagnosis. The computer or ECM controls all of the fuel delivery, spark timing and on some vehicles the charging system, that is why it needs a good power and ground pathway, ECM's do fail but I have found that a lot of problems are related to either a power supply or ground, this can be very time consuming. "
-------

"The ECM will remember that there was a failure and still have a light and a code, you need to clear the system before trying to retest, the best way to clear it is to disconnect the negative battery terminal, turn on the headlights, wait 30 seconds, turn off the headlights, reconnect the battery , start en"gine and drive normally, the ECM should relearn in about 20 minutes of driving unless there is still a hard fault then the check engine light will turn right back on and you can get the code..
-----------------------------
One of the cheapest ways to replace an ECM is to pull one out of a wrecking yard.

May 11, 2015 | Cars & Trucks

1 Answer

2002 jeep liberty feels like it stalls and will lose power if let off gas and then give gas again it will go. Also check engine light is flashing.


When the check engine light flashes it means the the ECM is receiving conflicting or out of range information from one or more of the vehicles engine management sensors, and has gone into what is known as open loop (or limp) mode. This allows the vehicle to continue to run, although poorly perhaps, until the engine can be serviced. It is not recommended to run the engine this way for long, as damage can be the result. Have the ECM codes read and the engine services as soon as possible to clear up the issue.

Aug 05, 2014 | Cars & Trucks

1 Answer

Reset check engine light


will have to purchase a obd II code reader to clear the code and reset ecm

Sep 16, 2013 | Toyota ECHO Cars & Trucks

1 Answer

Check engine lite on .pull codes p404. Also has lite miss on easy acceleration from stop.Need to pass state emissions test


P0404 EGR circuit range just replace the EGR,the light miss is from your egr pintle being stuck open. either you clear the code with a scan tool or if you dont have one it will take 2 trip of no emission problem for the ECM to clear the check engine light,

May 05, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

All of the sudden my check engine light, my VSC light, and my TRAC OFF light came on. Any thoughts?


You need to have the ecm scanned for codes. The VSC and TRAC OFF lights are one just because the Check engine light is on. Once you clear the code in the ecm they will go off too.

Nov 11, 2010 | 2004 Toyota Highlander

1 Answer

Diagnostic code po171 cleaned maf sensor check engine light still on.. How do I clear check engine light?


Remove the Negative battery terminal for 1 minute and reconnect, this should reset the stored codes in the ECM.

Oct 14, 2010 | Jaguar XJ8 Cars & Trucks

1 Answer

How do you reset the check engine light on a 2003 gmc yukon xl


the check engine light means you have a trouble code in your vehicles computer. After fixing the problem with the yukon the check engine light can be reset sometimes by disconnecting the battery and disconnecting the ECM fuse. Although some parts stores are known to check your codes for free they might also clear them with a scan tool.

Feb 26, 2010 | 2003 GMC Yukon XL

Not finding what you are looking for?
2006 Toyota Corolla Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...