Question about 1985 Toyota Land Cruiser

1 Answer

What do i set a 3f valve clearance with LPG - 1985 Toyota Land Cruiser

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 831 Answers

0.8mm

Posted on May 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the valve clearance for intake valve and exhaust valve for mitsubishi engine 4D32?


Please follow link to complete instuction's on the Correct way to set valve clearance on the 4D32 engine type.
6 INTAKE AND EXHAUST VALVE CLEARANCE INSPECT AND ADJUST

May 15, 2016 | Mitsubishi Cars & Trucks

1 Answer

Valve setting


Personally, the valve clearance (if nobody's been messing with it) would be last on my list of suspected causes.. Knowing diesel engines like I do, my very first suspect would be a dirty fuel filter.

Dec 03, 2013 | Cars & Trucks

1 Answer

Valve clearence settings mazda protege 2003


This is for a non turbo2_24_2012_5_45_49_am.gifNew adjustment shim =Removed shim thickness+ measured valve clearance- STANDARD VALVE CLEARANCE (0.26 mm or 0.010 inch)

Feb 24, 2012 | Mazda Protege Cars & Trucks

2 Answers

I have a 1982 chevy That i just put a new Carbutor on and I am running LPG and Gas but can't get it to idle right running on LPG do I need to change needle valves


Hi there tippo, It chould be the needle valves but i am more leaning towards the air/ fuel/ LPG not being at the correct ratio. If you are unfamilliar with running both gasses at the same time you may want to take it in to be adjusted. Also you can ask them what they are doing, a lot of shops out ther would be willing to show you how to make the adjustments. Mine would. I hope this helps you please leave feedback if i was of some assistance.

Mar 30, 2011 | 1983 Chevrolet Silverado

2 Answers

I have problem with my engine 4K toyota. It heard an engine noise during idling, for my little knowledge in engine repair, can you give me any procedure mannuals in adjusting engine valves for my...


Valve Clearance Valve clearance is there to allow the valves to cool in between combustion events (spark), and to make sure the valve closes properly and contains the combustion explosion. You need to cool the valves a little bit, the exhaust valve moreso than the inlet, as it's what sees the most heat as spent burnt gases go past it into the exhaust port. Run too little clearance and you'll cause the valve to "weld" a little bit to its' seat every time it closes, and then take seat metal off again when it opens. Do this enough times and you burn out the valve seat and need the head reconditioned. However, by running less clearance, the valve stays open for that little but longer, and you get more air in and out of the motor, and make more power. Run too much clearance and your motor just sounds like a diesel and loses power and tappet rattle annoys you while you're driving, so it's better to err on the side of caution.
The stock valve clearance (0.008" inlet / 0.012" exhaust, warm) is pretty good for any of the cams I've listed above, they're well-sized street cams, not really wild top heavy race cams that require super high compression to work, so don't be afraid to close the valves up a bit from the suggestions of the cam grinder, which will usually say between 0.010" and 0.014". There are a few ways to set your valve clearances:
Yellow Book Method This is from the factory 3K/4K/5K engine manual, aka The Yellow Books. It's the quick and lazy method.
Set engine to #1 TDC. Crank pulley timing mark should be on 0, distributor rotor should be pointing towards spark plug 1 or 2. Set tappets (counting from the front) 1, 2, 3 and 5. Rotate engine 360 degrees, crank pulley to 0 again, distributor rotor turned 180 degrees. Set tappets 4, 6, 7 and 8.
Nine Method I've never really gotten into doing this, takes too much time and maths for my liking :P Rotate the engine through its' range of movement, as one valve is "on the rock" of its' max lift, subtract the valve number from 9 and that's the tappet you should be setting. For example, if #8 valve is open, set clearance on valve #1. If valve #7 is open, set clearance on #2. And so on.
Stewart uses this method, and rotates the camshaft through its entire base circle and sets the clearance at the highest point. Which is a pretty good idea, as it compensates for the possibility that the base circle has been ground unevenly, and allows you to run the proper valve clearance that you want to run, instead of something that may be a few thou larger in reality.

Feb 10, 2011 | Toyota Corolla Cars & Trucks

1 Answer

I purchased spark lpg before two months & found occasionally malfunctioning indicator comes up & low pick up in lpg mode.Even after showing in the service center twice for 3 days they are not able...


please explain what the problem is in plain english as iam having trouble working out whats wrong ,i am assuming that vehicle has had LPG conversion fitted and now its a idle problem ,well on the intake side is a valve thats fitted for the LPG and this valve isnt letting enough air through its some sort of safety valve as i remember and what i do here is remove it and make a flap type valve from a coca cola can ,then it will work ok

Dec 19, 2010 | Chevrolet Chevette Cars & Trucks

2 Answers

Valve clearances for a ford econovan 1.8lt, 1990


what are the valve clearance specs for a 1990 ford econovan maxi

Mar 14, 2010 | 1989 Ford Econoline

2 Answers

Toyota 3y engine fuel system


LPG 3Y engine toyota crown comfort automatic - fuel consupmtion is 13.30litre per 100km? How can this be reduced?

Jan 08, 2010 | 2002 Toyota Camry

1 Answer

Top end knocking noise


Try doing a compression test to see if all cylinders have same reading.
If compression is low on 1 cyl, that is obviously where to start.
Check the valve clearances to that cylinder.
If valves not set too tight, then it must be piston related.

Jun 12, 2008 | 1997 Saab 900

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...