Question about 2002 BMW 3 Series

1 Answer

Remote controll not working not - 2002 BMW 3 Series

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 44 Answers

The best thing to do is:

1- Replace the battery that is located on the back of the remote. If nothing happens then;

2- Try reprogramming the remote control with the car. if you have the original manuals, then it will precisly tell you how to reprogram your remote to successfully communicate with the alarm module in the car.

The problem could also be the Alarm module receiver.

hope that helps. Let me know.

Posted on May 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse do I change my remote only works non inch away


Replace the battery in the remote control, clean the emitter lens on the remote control, and clean the face of your receiver. Should solve the problem.

Jul 31, 2014 | 2006 Mercedes-Benz CLK 500

1 Answer

2011 cruise control and remote start do not work after EVAP problem.


the remote start and cruise control will not work if the codes are stored just because the light is off doesn't mean the codes are cleared

Jul 19, 2012 | 2011 Chevrolet Avalanche LT

1 Answer

Both car remote controls stopped working


The receiver probably just needed resetting and reprogramming. I am surprised three are working - normally the receiver will only allow two.

Jun 29, 2017 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Hello the remote control is working but the


Please check & ensure the infrared is emiting from the remote control. Though we cant see this infrared beam with bare eyes, there is a trick to do so in http://www.unique-stuff.co.cc/fixing_remote_control_check_infrared.html Most of the problems is weakened infared beam. Replace the batteries when needed. Hope this fix the remote control problem.

Jan 22, 2010 | 1995 Toyota Land Cruiser

1 Answer

How to recode remote to vahicle


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press lock or unlock button. Within 10 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
NOTE: If less than 3 remote controls are to be programmed, remove ignition key after programming last remote control.

Jan 18, 2010 | 2003 Honda Civic

1 Answer

Does any body know how to reset the ML350 alarm??....The remote control doesn't work after i replaced a new battery to the remote control. I couldn't even use the remote to lock/unlock the car. I was


SOME OF THE REMOTES REQUIRE THAT THE KEY BE IN THE IGNITION, IN THE ON POSITION. TAKE THE BATTERY OUT AND WAIT 10 MINUTES. THEN PUT THE KEY IN THE IGNITION AND INSTALL THE BATTERY WHILE THE KEY IS TURNED TO THE ON POSITION. HOPE THIS HELPS YOU. PLEASE KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. GOOD LUCK

May 18, 2009 | 2007 Mercedes-Benz ML350

1 Answer

Chevy Subruban 2007 remote control


you will have to take it to a chevy dealer to have it reset...

Feb 28, 2009 | 2005 Chevrolet Suburban

1 Answer

Remote key fob will not work-battery replaced


VW/AUDI/SEAT/SKODA



Remote Control Programming (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Using the remote control press the Unlock button once, and the horn
will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.

For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote
control.

Remote Control Erasing (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Press the remote control unlock button 5 times in 1 second intervals.
A short horn will sound.

4. Wait 6 seconds and press the unlock button once to activate memory
erase.

5. Switch ignition OFF, all remotes are now erased.

Dec 24, 2008 | 2004 Volkswagen New Beetle Convertible

3 Answers

Changing a battery on a Cobra 7777 remote control


The battery in the 7777 remote is a CR2032. If upon changing the battery the remote fails to work then you should stand next to the car and hold down both remote buttons for around 10 seconds to reactivate it. The remotes LED will flicker rapidly during this process. Keep holding both buttons until the LED stops flickering then release both buttons. The LED should now be on constant, press the larger of the two buttons and the remote should now be re-synced.
Note: This procedure is not to program the remote to the alarm, but to re-synchronise it.

Aug 20, 2008 | 1999 Mazda 626

2 Answers

Keyless / remote control - Toyota vienta vxi


No, not true. We replace remotes regularly, and have never had a need for a "working" remote. The keyless entry system does not "disable" itself. Hope this helps.

Jul 12, 2008 | 2003 Toyota Camry

Not finding what you are looking for?
2002 BMW 3 Series Logo

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...