Question about 1989 Toyota 4Runner

1 Answer

Dropped the gear box for cluth and pp replacement, replaced the engine seal, twice-just bench tested today and still leaks # 3, what am i missing here???? first time working on a Toy and don't have a manual.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,297 Answers

You are not missing anything
so common, but most common with aftermarket seals
I've seen this on every make and model

assuming the leak is from the engine seal I do not see any modified part numbers yet

however, Toyota finally has a modified part for the transfer case, covered under TSB #022

Posted on May 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999. How can I replace front diff seal?


on the actual front diffr, pinion or the front transfer case seal
the front seal is like the rear.
its a crush cage.
that means when you remove the pinion yoke/flange big bolt
the crash cage is destroyed. also wrecking pinion gear to ring gear back lash..oops.. big big mess-up there...$$$$$$
and such cage must be replaced.
questions????????????
how can you be sure its leaking, when the engine this old loves leak oil

i bet that oil on the ground does not small at all like the nasty stink of hypoid GL5 gear lube. I BET

why not post how to find leaks first
and not do $1000 damage

no engine size posted G16? J20?>
The G16, ill demonstrate (coin toss)
Distributor 2 , o-rings leak like made, all do this old !!!!
same with the 60k mile service and valve cover gasket
all leak, for that reason alone, on all 1990s era
next is cam seal
crank seal
pan seal (or pan is rusted thru as many see (today)
oil pump seal
and gawd forbid the rear main seal , engine.


easy peasy japanezzy

why not ask your mechanic to sniff that oil first and save a fortune
guessing.
!!!!

see man pulling axle to remove pan
wana do that?
http://www.fixkick.com/axles/Pan-drop/pandrop.html

to replace this seal, remove the carrier first
then take it to a shop that can rework the carrier
the correct way.

Jan 25, 2016 | Geo Tracker Cars & Trucks

1 Answer

05 malibu leaking oil from rear of engine


This may be from excessive pressure in the sump from blow-by from the compression process . It is from a blocked PCV valve that is not equalising that pressure. I have also known oil leaks to happen because the rear main bearing cap is leaking oil past the join around the bolts (loose) or no sealing compound used in assembling the rear main bearing.. I would look at the PCV valve as it is the cheapest test first.. Check that the oil is not coming from the front gear box seal or torque converter seal.

Mar 08, 2014 | Chevrolet Malibu Cars & Trucks

1 Answer

Front seal leaking in gear box


If it is the front seal in the gear box then the box has to come out. The seal is in the extension housing that the clutch throw out bearing runs on and the seal can be replaced by removing that housing . However mostly if that seal leaks then the front bearing on the clutch shaft may be failing allowing the shaft to move and that is why the seal leaks. If the front of the box is dry then the oil leak may be the rear main seal of the engine so it is best to check both arrears as the oil leaks from the same point in the bell housing

Aug 26, 2013 | Cars & Trucks

1 Answer

Has a miss and oil leak suddenly. About half a quart just by moving it.


ENGINE MISSING CAN BE WEAK COIL.BAD PLUGS AND WIRES.REPLACE DISTRIBUTOR CAP AND ROTOR.FUEL FILTER STOPPED UP ALSO FUEL INJECTORS CLOGGED UP CAUSES MISSING.CHECK UNDERNEATH CAR WHILE IDLING.IF YOU LOSING A LOT OF OIL.FRONT CRANKSHAFT SEAL OR REAR MAIN SEAL LEAKING OIL.LEAKING VALVE COVERS.DO A COMPRESSION TEST.AND CHECK CONDITIONS OF SPARK PLUGS.IF PLUGS SOAKED IN OIL.VALVE GUIDES + SEAL LEAKING OIL IN COMBUSTION CHAMBER.

Sep 18, 2010 | 1992 Cadillac DeVille

1 Answer

How to fix oil leak from top of a manual gearbox housing


sorry but its going to be a big job. you need to remove the gearbox to open up and get to the seals. you could try and use an additive in the gear box, its like oil seal for engine you can get it for engines gear boxes and difs and power steering. it sometimes goes by seek and seal, in older vehicles its quite good. you will need to replace the oil it will need to be done twice to clean it all out so it can get a good seal.. i.e change oil run engine get the gearbox to move for 20 min then change the oil as its warm not hot so let it cool down for 10-20 min then drain. put the seek and seal in and top up with oil and run as normal, check after a few days to see if its worked. usual does.

Jun 12, 2017 | 1995 Ford Ranger Supercab

1 Answer

Clutch fluid is leaking inside of the car 240sx


You need to rebuild the seals in the cluth master cylinder. The seal around the pedal shaft that actuates the clutch is leaking fluid past the seal and onto the shaft connected to the pedal, inside the cabin. 
A good parts store should be able to get you a seal rebuild kit, or remove the cylinder and bring it to a clutch shop or Nissan dealer and have them rebuild it for you. This is cheaper than dropping the car off and having them do all of the work. 
Dismantling the master cylinder, replacing the seals, filling the system with fresh fluid and bleeding it should solve your problem. Be sure to replace all of the seals at one time, and don't be tempted to only replace the one that is leaking at the moment. They should all be the same age to last without further leaking. Otherwise you'll be chasing a series of problems with your clutch as the other old seals fail over time.
Hope this helps.

Dec 19, 2008 | 1990 Nissan 300ZX

1 Answer

Fluid leak around starter


It may be a rear crank seal, or oil from the torque converter (automatic) or the input seal on the transmission. Check your fluid levels in your engine and trans. A visual inspection will help also. you could remove the inspection panel on the bottom of the trans bell housing. As for the clunk I would be leaning towards more of a starter issue for that.

Dec 08, 2008 | 2002 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...