Question about 1991 Chrysler New Yorker

1 Answer

Car wont start, the starter is good it has the volts of 12.6 but the start wire only has 1.6 volts .

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

You have very bad corrosion in the cable that will block full voltage through the entire battery cable
replace the cable is the only hope for your dilemma

Posted on May 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

A friend grounded the power wire to my ignition on my 96 yzf600r and now it wont start I replaced the fuse and the lights come on but wont turn over please help


Check every switch,solinoid, and wires from the ignition connector to the starter, with a volt meter, follow the 12 volts from the start button to the starter to the battery.
On a wild guess, the starter solinoid doesn't have 12 volts coming out of it when it is engauged.

Best of luck!

May 03, 2015 | Cars & Trucks

1 Answer

Car wont start just one click and a hum when key is turned


Hello! do you have a multimeter and a little experience using it? if not just let me know...If you do set it to read 12 volts...clip the (-) probe to the (-) battery terminal and the (+) probe to the Brown wire that connects to the starter motor...Have someone turn the key to start...+12 volts must be on that Brown wire...If not the starter relay (even though it clicks) is defective...Check for 12 volts on the large Red lead connected to the starter...If voltage is correct the starter is defective; replace starter...See diagram below for location of starter...Guru...saailer


12_13_2011_9_21_47_pm.gif

Dec 13, 2011 | 2000 Chrysler Grand Voyager

1 Answer

My car would not start thought it was the battery, replaced battery for new, car will not turn no sound at all.


Now you must check the starter. The large cable going to the starter supplies 12+ volts. The small wire supplies 12 volts when the key is turned to the start position. Using a volt meter or 12V test light check for voltage at the small wire when the key is turned to start. If 12 volts are now present and your engine grounds are good then the starter is bad. You can try to bamg on the starter with a broom stick while someone turns the key to start. sometimes this will get the starter moving again. but not for long. starter replacement will be required.

If 12 volts is not present at the small wire when turning the key then you may suspect a blown fuse, fusible link, bad starter relay, neutral or clutch safety switch, or faulty ignition switch.

Sep 25, 2011 | 1999 Nissan Altima

1 Answer

My husband replaced the turn signals & headlight & now car wont start


Hello! I sent a test procedure to you Wednesday evening but It appears you did not receive it ..This is the path for Battery and Ground to pull the crank relay which applies +12 volts to the starter solenoid..Either there is a fault in this path or the starter itself was damaged in the collision...Leaving the ignition switch when in start ...+12 volts on the Yellow wire goes to the Crank fuse (10A)...Other side of fuse is Purple wire to PCM C-2 Pin # 23...+ 12 volts at this point...PCM sends a ground on C-2 pin #76...Yellow/Black wire to crank relay....+ 12 volts from the PCM ABS fuse (10A)...via Park/Neutral switch to crank relay...Relay pulls and applies +12 volts on the Purple wire that goes to the starter...That +12 volts, if there,indicates a starter damaged in the collision...If not there chase it back until you lose it...Would you be so kind as to not rate my solution until the test procedure is accomplished...Send a comment..saailer

Sep 21, 2011 | 2000 Pontiac Montana

1 Answer

My car wont start but my battery is good it just clicks


if your battery has 12 volts and you can hear click noise , try to locate the click noise. If that is coming from the starter location then the starter mtr is not working.a voltage check at the starter mtr with the key in the start position will verify the problem. if 12 volts is not present at the starter mtr thethe start switch or wires could be the problem

Feb 14, 2011 | 2006 Dodge Charger

2 Answers

My car will power up but wont crank i believe its the starter


check if you're getting a 12 volt signal to the small wire going to your starter when you try to start it. And also 12 volt all the time to the big wire. if the small wire doesn't have 12, then I'd suspect the ignition switch, if both get 12, then it,s definitely the starter.

Jan 09, 2011 | 2001 Ford Windstar

1 Answer

Wont start,no sounds no power,completely dead


You will need a volt meter to figure this one out. Battery voltage? Should be above 12 volts, and while you are trying to "crank" the engine over, if it's still over 12, you need to see if that power is getting to the starter motor. If it goes below 9 or 10 volts, you either have a bad battery, or the starter motor is shorted, or bad.
To test the starter, you should have a large wire going to the starter that has 12 volts all of the time from the battery. A smaller wire will have 12 volts only when the key is turned to "start". If you have these and a good ground, the starter motor is bad.

May 30, 2010 | 1997 Toyota Corolla

1 Answer

Won't start.


That's possible, but if you have power at the starter solenoid to close the contacts then check to see if the 12 volts are going through it(probe the large wire on both sides of the solenoid for 12 volts) and on to the starter, if this is the case, check for 12 volts at the starter lug where the large power wire hooks to the starter, if you are getting at least 12 volts at the starter lug, I would say you have a failed starter motor. Good luck !

Nov 29, 2009 | 2000 Lincoln Navigator

2 Answers

I have a 95 eclipse n/a that wont start. it was running perfect, amazing actually, and then all the sudden wouldnt start. all lights and radio come on in the car(battery is fine, tried jumping it just in...


If the starter isn't turning it is not an o2 sensor. You need to make sure you are getting power to the starter, use a test light and a voltmeter check and make sure you are getting 12 volts to the starter if you are getting 12 volts from the battery to the starter check and make sure you are getting 12 volts from the ignition switch which will be the smaller wire. If you are getting 12 volts through that wire then the starter is bad. If you are not getting 12 volts or any volts you need to make sure the fuse and relay for the starter are good then check and make sure you have power coming out of the ignition switch going to the starter you will need an electrical schematic for the car to trace the wires to find the correct one.

Sep 27, 2009 | 1995 Mitsubishi Eclipse

1 Answer

Wont start


Hi first check for volts you should have 12.6 volts next check if the wire that go's from the switch to the starter there should be 12. volts if not check relay and fuse good luck

Sep 04, 2009 | 2003 Pontiac Grand Am

Not finding what you are looking for?
1991 Chrysler New Yorker Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...