Question about 1989 Ford Bronco

1 Answer

Replacing a serpentine belt 1989 ford bronco - 1989 Ford Bronco

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Most have a diagram in the engine compartment on the front by the latch. if not draw a diagram of how it is routed. Removal is done by releasing the tensioner on the passenger side next to the alternator. route new one leaving going under the tensioner the last part, then lift tensioner and route under it.

Posted on Aug 01, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: I need to replace a serpentine belt on a 1984 Ford

No - your belt cannot be replaced without taking the fan off. More than likely, you also have multiple belts. You will have a 1/2 inch spot on most of the plates to tighten each individual component. Look for a place to attach a 1/2 inch breaker bar/ratchet next to the alternator, steering pump, smug pump, etc. These should all be v-belts on a 1984, not a true serpentine.

Posted on Nov 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wireing ford 89 bronco 2 solenoi setup


I've had this problem. I replaced the battery cables and ends and solved my problem.

May 02, 2014 | 1989 Ford Bronco II

1 Answer

How do I replace power steering pump on a 1993 Buick centry


place a drain pan under pump. disconnect negative battery cable. remove inlet and outlet hoses a.d let drain. remove the serpentine belt from the pulleys by loosening the automatic belt tensioner. remove the three pump mounting bolts and the pump. using a suitable pry bar remove the retaining clips from the reservoir separate the reservoir from the pump. install the reservoir to the pump with new o ring seal. remove pump pulley and put on new one.

Oct 27, 2013 | 1989 Ford Bronco II

1 Answer

1989 ford bronco C6 transmission leaking fluid at manual shaft


I have a 1989 Ford Bronco 351 w with a C-6 Transmission. I just did a transmission service, replacing the gasket and filter. Now my transmission is leaking when the bronco sits for a few days.Help!!!

Aug 08, 2012 | Ford Bronco Cars & Trucks

1 Answer

It squeals from the time i start the engine and continues throughout my trip untill i turn it off. Then when i start it again, it may or may not. If it doesnt squeal the moment i turn it on, then it d


Squeals are usually belts or bearings, check your serpentine belt for cracks and damage . There are it'd products like stop squeal you can use on your belt. If its the belt it will work, otherwise check bearings on all pulleys.

May 24, 2012 | 1989 Ford Bronco

1 Answer

Serpentine belt dia


geterrollin_5.jpg
Hope this helps!

Jan 23, 2011 | 1989 Ford Bronco

1 Answer

I need to replace a serpentine belt on a 1984 Ford Bronco. Can anyone tell me where to find the belt tensioner? Also can the belt be replaced without removing the radiator fan? Thanks.


No - your belt cannot be replaced without taking the fan off. More than likely, you also have multiple belts. You will have a 1/2 inch spot on most of the plates to tighten each individual component. Look for a place to attach a 1/2 inch breaker bar/ratchet next to the alternator, steering pump, smug pump, etc. These should all be v-belts on a 1984, not a true serpentine.

May 08, 2010 | 1984 Ford Bronco

1 Answer

Diagrams of serpentine belt 87 ford bronco


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1987/make/ford/model/bronco/1987_ford_bronco_drive_belt_routing_diagram.htm

Nov 15, 2009 | 1987 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...