Question about 1996 Lincoln Town Car

1 Answer

HOw much torque do you put on an air conditioning compressor mounting bracket for a '96 Lincoln Town car?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,841 Answers

50 ft/lbs will be sufficient.

Posted on May 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoiw to replace the air ride suspension comporessor on a 96 cadillac concours


Loosen exhaust system at each end of muffler and remove muffler heat shield to get at compressor assembly. Disconnect air lines and electrical wiring, remove inlet filter from underbody mounting, two bracket screws attaching compressor mounting bracket to suspension, and then remove compressor and bracket assembly toward the rear of the car next to exhaust pipe.

May 18, 2015 | Cadillac DeVille Cars & Trucks

1 Answer

I am changing the airride suspension compressor out in my 1998 lincoln town car ,but cant get the frot of it loose.


Never mind air suspension put coil spring from 1990 towncar did that many time not as soft but prety close

Mar 07, 2015 | 1998 Lincoln Town Car

2 Answers

Where is the compressor for the air ride suspension on a 2000 lincoln town car? And is there a fuse for it?


It is located under the air cleaner box. the fuse is located with the relay in the fuse box under the hood, it is not marked but there should be info in the owners manual.

Nov 15, 2009 | 2000 Lincoln Town Car

2 Answers

How do i change the starter on a 96 century


If it's the 3.1 or the newer 3100 the starter should just be a couple 13 and 15mm bolts. Plus the nut for the cable. Hope this helps.

Jul 13, 2009 | 1996 Buick Century

1 Answer

Replaced air condition compressor an is cranking but not starting


Check the crank sensor that is stuck in the block right by the A/C compressor. You had to unplug it to replace the compressor.

Jun 28, 2009 | 1999 Lincoln Town Car

2 Answers

Air only blows hot on 96 lincoln


Sounds like the heater and a/c blend door actuator. It is located under front center of dash below windshield. Dash must be removed to replace it. I've done it several times.

Jun 18, 2009 | 1996 Lincoln Town Car

1 Answer

How to replace accessory serpentine belt on 1996 Riviera


The supercharged 3800 engine uses two accessory drive belts. The outer belt drives the supercharger. The inner belt drives the generator, power steering pump, coolant pump and air conditioning compressor. All driven accessories are rigidly mounted to the engine. Drive belt tension is maintained by the spring loaded belt tensioner. Each belt has its own tensioner.
Remove: Place a jack with a block of wood on it under oil pan to support engine. Caution : Be sure the wood block extends past the width of the oil pan to avoid damage. 
Torque axis engine mount bolt where it connects the mount to the engine mounting bracket. 
Electrical connector from crank sensor. 
Engine mounting bracket lower stud and lower engine to allow stud to clear frame rail. 
Raise engine and reinstall bolt into torque axis mount. Lower engine to allow spacer to be removed. 
Belt(s)

Istalling: Belt. 
Spacer. Remove bolt from torque axis bracket and lower engine. 
Electrical connector to crank sensor. 
Mounting bracket stud. 
Raise engine and install torque axis mount bolt. 
Tighten bolt to 87 Nm (52 lb. ft.) 

Good luck and hope this helps.

May 05, 2009 | Buick Riviera Cars & Trucks

1 Answer

Horn note adjustment on 95 lincoln town car?


you don't you have 2 horns - 1 high note, one low note. maybe one is not working.

Horn Mounting Location The horns (13832) are mounted as follows:
  • On Town Car, the horns are mounted to the horn mounting bracket (13830) that is attached to the LH side of the radiator support (16138)

Mar 15, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
1996 Lincoln Town Car Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...