Question about 2003 Ford Crown Victoria

1 Answer

Crown Vic: Window shield wipers turn on by themselves.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

DISCONNECT WIPER SWITCH IF WIPERS STOP REPLACE SWITCH.IF WIPERS DONT STOP. YOU HAVE A DEFECTIVE LIMIT SWITCH IN MOTOR.

Posted on May 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the wiper motor on a 2005 crown vic


The wiper motor is under the black plastic cowling below the wiper arms.

Sep 13, 2011 | 2005 Ford Crown Victoria

1 Answer

My wipers are coming on by themselves on 06 Crown Vic Police Interceptor, squirter works, knob works, but when I am going down the road with everything in off position, they randomly come on with no rhyme...


Hello, Its the Multifunction switch for the turn lever and wiper controls. The contact points are usually corroded or loose and a bump can cause them to make contact. The usual solution is to replace the switch. Only a few styles are capable of being cleaned and disassembled.

You will need to remove the steering column cover. Usually requires moving tilt wheel several times to guide plastic cover out of place. There are 2 wiring harnesses attached to the control. They have flimsy latches and care needs to be taken when spreading the latches or they will break.
The switch has several torx head screws or in some cases Security screws holding the part to the column.

There are differences in the number of contact terminals in the switch. Some have 2 additional posts for other functions. Best to bring in old one to get correct part.

Jun 28, 2011 | 2005 Ford Crown Victoria

1 Answer

How do I change my wiper blades on my '92 Crown Vic? Do I have to change the whole wiper arm?


Most auto parts stores will gladly change out the blades for you. As far as your question.......No, you only have to replace the blades and not the completer wiper arm.
Hope this helps

Aug 26, 2010 | 1992 Ford Crown Victoria

1 Answer

2002 ford crown vic. driver side wiper not working? passenger side works


the linkage between the wiper motor and the wiper arms needs to be replaced. the stud on the one side is stripped and that is why it doesn't work as it should. this happens usually when the wipers are left on in the winter with the blades freezing to the windsheild. turn on the car with frozen blades tends to strip out the teeth holding the wiper arms onto the linkage

Jun 09, 2010 | 2002 Ford Crown Victoria

1 Answer

How to remove wiper arm 96 crown vic


WHERE THE WIPER ARM AND SHAFT COME TOGHER THERE IS A LEVER LIFT UP THE WIPER SO THAT IT IS POINTING AT THE SLY AND PRY OUT THE LOCK AT THE BASE OF THE WIPER ARM .

Sep 12, 2009 | 1996 Ford Crown Victoria

2 Answers

Wiper motor replacement for a 99 crown vic


I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

May 06, 2009 | 1999 Ford Crown Victoria

1 Answer

Wipers will not park on 93 ford crown victoria


Hmmmm... if you replaced the motor you must have cleaned the area housing the arm mechanism. I had the same problem and found the problem to be in the arm assembly box on the firewall. Under the hood, triangular shaped box with snap on top was full of dirt, leaves and pine needles... I removed all the **** & my wipers now park as they should!!

Mar 14, 2009 | 1993 Ford Crown Victoria

1 Answer

Wipers


It's probably going to be the switch arm itself.

The part is a bit pricey, but it does come with the wiring diagram to place the new one in there.

The switch is the whole thing, turn signal, wipers, etc, and the arm.

Dec 20, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

Related Topics:

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...