Question about 2001 Pontiac Bonneville

1 Answer

Hi-trying to find a website with free access to a diagram or re-assembly directions for repairing a 91 bonneville wiper motor and wiper assembly. Can you recommend any to me? Thanks!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 438 Answers

Hello ,,my advice to you is to purchase a Chilton or equivalent service manual for your vehicle,
all the necessary information to service
most any problem can be found within the pages, these manuals can be obtained
from almost any parts suppler at a reasonable cost

Posted on May 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my wipers on my 1998 chevy lumina only work non hig


Do you know how to do electrical testing ? Here is diagnostic trouble flow chart .You will need a wiring diagram . Go to http://www.bbbind.com/free_tsb.html free wiring diagrams . You can see basic automotive trouble shooting videos on you tube if you are not familiar with this .
Wipers Low Mode Inoperative, High Mode Operates

2
Disconnect wiper motor connector C1.
Turn the ignition switch ON.
Set the wiper switch to LO.
Connect a test light from wiper motor connector C1, terminal B, to ground.
Is the test light on?
--
YES - Go to Step 6
NO - Go to Step 3

3
Inspect for a poor connection or an open in CKT 91.
Is a poor connection or an open present?
--
YES - Go to Step 4
NO - Go to Step 5

4
Repair the poor connection or the open in CKT 91.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

5
Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column -Tilt.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

6
Connect a test light from wiper motor connector C1, terminal C, to ground.
Is the test light on?
--
YES - Go to Step 10
NO - Go to Step 7

7
Inspect for a poor connection or an open in CKT 95.
Is a poor connection or an open present?
--
Go to Step 9
Go to Step 8

8
Repair the poor connection or the open in CKT 95.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

9
Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column -Tilt.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

10
Inspect for continuity between wiper motor connector C1, terminal A, and connector C2, terminal B, using a J39200.
Is continuity present?
--
Go to Step 12
Go to Step 11

11
Repair the open in CKT 196.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

12
Inspect for a poor connection to the wiper motor at connector C1.
Is a poor connection present?
--
Go to Step 13
Go to Step 14

13
Repair the poor connection at wiper motor connector C1.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

14
Replace the wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

Feb 29, 2016 | Cars & Trucks

2 Answers

How do I remove the rear wiper assembly from a Dodge Durango 2003?


Most Chryslers from this year band require removal of the rear door's liner to access the motor. The motor is held on by two or three compression nuts with bolts that pass through the motor housing/frame. NAPA has new ones or you can use simple nuts and use both metal and rubber bushings to prevent possible rattling noise after mounting a new motor. A car or your year it is best to go to a recycle yard and get the whole assembly for cheap so you don't need to disconnect the motor from the wiper arm linkages. It's not difficult. The wiper must be removed from the back of the car and the large screw underneath the rubber gasket removed as well. The rest of the removal/install process is done from inside the rear door, once the rear door panel is removed.

Apr 03, 2015 | 2003 Dodge Durango

2 Answers

How to replace a 99 se Bonneville windshield wiper motor


Windshield wiper motors are generally easy to replace. You need to remove the windshield wipers and take off the small grill panel above the hood and under the windshield. You should see the motor in there. It simply unbolts and unplug the electrical connector and replace it with a new one.

Mar 21, 2015 | 1999 Pontiac Bonneville

1 Answer

Free belt routing diagrams


Hi there,here's a link to your belts,join the AutoZone site,it's free then you can use their repair guides free. Repair Guides Engine Mechanical Components Accessory Drive Belts... Here's another cool site to see. 2002 Pontiac Bonneville Serpentine Belt Routing and Timing Belt Diagrams

Sep 04, 2014 | 2002 Pontiac Bonneville

2 Answers

Ecm wiring diagram 1991 pontiac bonneville


BBB Industries online under Technical

Jan 25, 2014 | 1993 Pontiac Bonneville

2 Answers

2000 bonneville wipers wouldnt turn off replaced motor with a used one from junkyard.worked for a while now wipers stop going all the way up


I would pull the motor assembly again and cycle the wipers by hand to get the blade assembly back to park horizontal position then re install. This is common when replacing the motor that the nylon gear assembly in the motor was not in horizontal park position

Dec 21, 2012 | 2000 Pontiac Bonneville

1 Answer

The wipers started losing range of motion. was told motor going bad. replace the motor and still have no range of motion.


It was never the motor itself, but rather the arm assembly that the wipers hook up to. That is what you have to change out. There are bushings in the assembly that get worn out, 'sloppy' is what it is called, and that causes the loss of range.

If you grab one of the wipers, and try to move it up and down, it SHOULD be tight, meaning it doesn't move much. But, if there is significant movement, then the bushings in the assembly are worn out.

I hope this helps.

Jun 10, 2011 | 1998 Pontiac Bonneville

1 Answer

Wiring for Wiper system


most likley the whole switch assembly needs to be replaced.You cant repair just the wiper.

May 24, 2008 | 1988 Jeep Cherokee

Not finding what you are looking for?
2001 Pontiac Bonneville Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8732 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...