Question about 1991 Toyota Tercel

1 Answer

What could be wrong when toyota has power but when you push clutch in to start engine nostart

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 973 Answers

Some manual transmission cars have a switch on the clucth pedal so the engine won't start unless the clutch is pressed in. You could have a defective switch.

Posted on May 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turns over but won't start getting gas and good fire does it every time it sets for 24 hrs


Engine cranks but won't start - YouTube

? 8:03
www.youtube.com/watch?v=1L4nB2NdA0U
May 16, 2014 - Uploaded by jimthecarguy 2003 Ford Taurus 3.0 liter 24 valve no start cranks OK.You will not believe what the problem is.You have to ...

Auto,Car,truck Won't Start, diagnostic help, start test, advice

econofix.com/nostart.html
After the engine is spinning over, fuel is admitted to the cylinders and is ignited, and the engine starts to run under its own power. If a vehicle "turns over" but won't start, there is probably NOTHING WRONG with your starter, battery, or alternator.

Oct 02, 2015 | Cars & Trucks

1 Answer

Where is the clutch start cancel swith on a 2006 toyota tacoma


its on the pedal, use a flash light , see it? up top.
most cars is adjustable.

Dec 29, 2013 | 1997 Toyota Tacoma

1 Answer

Car stalls out when you push in the clutch


When you push in the clutch you are pushing the crank shaft forward in the main bearings but the action of the throw out bearing for the clutch pushing the fingers of the clutch pressure forward. For the engine to stall under this condition I would be checking the throw out bearing for seizure and acting as a brake on the pressure plate. Some clutch systems are part of the engine start system where you have to depress the clutch to start the engine (safety device) This may be faulty and shutting the engine down.

Oct 04, 2013 | 1992 Toyota Paseo

1 Answer

Metal on metal noise


hi,

most likely the throw out bearing is at fault. when you push the clutch a spinning bearing pushes the clutch plate away from the flywheel disengaging trans so you can switch gears. the transmission has to come away from the engine to fix it.

jm

Jul 04, 2017 | Toyota Corolla Cars & Trucks

1 Answer

My '95 Tercel won't start


clutches don't pump up unless there is air in the system. Check the slave cylinder for oil leaking. There may be a switch that has to be in the correct position to allow the system to start and unless you can activate it when the clutch is disengaged it will ne difficult to start. I would also check the battery with a load test as bad cells will not give a high enough crank speed to fire the engine

Apr 07, 2013 | 1995 Toyota Tercel

1 Answer

My toyota camry 1998 its five speed.But when i change gear there is no power to push the car going. Gear one is flat to gear five. smoke come from the left side of the engine block. I added oil but the...


Hi the problem you are having is going to be with the clutch plate you will find that it has worn down to the metal pins and has no actual clutch plate left.

What is happening is that when you put the car in gear and let the clutch up the clutch is slipping on the plate instead of gripping and this is why you loose the drive.

To solve this problem your going to need to buy a clutch repair kit if your doing the sork yourself or get someone else to fit the parts for you.

Your going to need to replace the following:
pressure plate
clutch plate
thrust bearing.

dont try driving the car as it is as you could cause damage to the gearbox if the clutch plate and pressure plate shatter so its not worth trying to move the car until you have had the clutch fixed.

getting the clutch replaced involves removing the gearbox from the engine and this is best done with the car on ramps as the gear box will come out from the bottom of the car so it needs to be high enough off the floor to allow you to remove the gear box, its not a hard job if you have done it before but it is heavy work and if you have not done this before then your best getting someone else to replace the clutch for you.

getting the clutch changed will solve your problem and get you up and running again in no time.

let me know how you get on or if you need further assistance ok

May 31, 2010 | 1998 Toyota Camry

1 Answer

My 1987 toyota pick up 5 spd will not start when you push in the clutch but it will as soon as you push the clutch start cancel button i beleive the clutch pedal switch is to blame it is not completeing...


There will be a switch on the clutch pedal bar under the dash somewhere. When you push in the clutch the pedal touches the switch and completes the circuit. It may be out of adjustment, or just worn out. You can either replace it, or remove it, and pigtail the wires together. Although, if you do that, be aware that it will start in gear, clutch out, and could be a safety issue.

Mar 14, 2010 | 1987 Toyota Pickup

1 Answer

I own a toyota 4x4 pick-up 1989 it was stored outside without running for 2 years ,now my pedal clutch stay stick.How can i fix it? Also how can i put oil in the gearbox(transmission)?


I assume the clutch won't release. Put the trans in neutral and start the engine. Let it get warm. MAKE SURE THERE IS ROOM TO DRIVE THE TRUCK, WITH NOTHING IN THE WAY. Stop the engine, put the trans in first, and start the engine. The truck will jump forward when the engine starts. Get it on a clear road, push the clutch pedal in, and hit the gas. It should come loose in one or two tries.

Jul 14, 2009 | 1991 Toyota Pickup

1 Answer

Chirping noise when engine is started


the noise is from a worn out clutch pressure plate release bearing, replace it..

Dec 10, 2008 | 2007 Toyota Tacoma

2 Answers

Power drain while depressing the clutch


it should have a clutch safty switch, what it does is if you try to start the car without the clutch pushed in it wont start. that switch could be trying to ground its self out. check where the clutch pedal is and you should see a form of push switch attached to it, check for exposed wiring on etc

Dec 10, 2008 | 1990 Suzuki Samurai

Not finding what you are looking for?
1991 Toyota Tercel Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...