Question about 2000 Chrysler LHS

1 Answer

Need to replace the ignation switch in my 2000 chrysler LHS

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 2,984 Answers

Removal & Installation

  1. Disconnect negative cable from battery.
  2. Remove the Instrument Panel Center Bezel, Chrysler and Dodge.
  3. Remove side trim panel to steering column cover.
  4. Remove the screws that secure the steering column cover to the instrument panel and relocate panel.
  5. Pull the steering column cover rearward at the top and right side of the cover to release the snap retainers from the instrument panel.
  6. Remove the screws that secure the instrument panel steering column cover reinforcement to bracket and remove reinforcement from the vehicle. Remove the 2 front mounting nuts.
  7. Remove the lower mounting nut.
  8. Slide the assembly rearward into the instrument panel and down to gain access to switch.
  9. Disconnect the electrical connector from the ignition Switch and SKREEM Module.
  10. Remove the interlock cable by depressing the locking tab and pulling straight.
  11. Remove ignition switch mounting screw.
  12. Squeeze the 2 locking tabs to remove ignition switch from the lockhousing .

need to replace the ignation switch in my 2000 - 485d77a.gif
Removal and installation of the ignition switch

To install:

NOTE A tab on the ignition switch indexes to a notch in the lock cylinder housing. Also, a slot in the end of the ignition switch fits over the shaft in the end of the lock cylinder housing.


  1. Use the ignition key to rotate the lock cylinder to align the ignition switch with lock cylinder housing.
  2. Insert ignition switch into lock housing until locking tabs are seated into openings on lock housing.
  3. Install ignition switch mounting screw.
  4. Install the interlock cable into the switch assembly. Attach electrical connector to SKREEM Module.
  5. Install switch assembly into Instrument Panel.
  6. Attach electrical connector to ignition switch.
  7. Tighten the 2 mounting nuts.
  8. Tighten the lower mounting nut.
  9. Install steering column reinforcement.
  10. Steering column reinforcement installed.
  11. Install the Steering column reinforcement cover.
  12. Install trim panel end.
  13. Install the Bezel cluster.
  14. Install the ignition switch bezel ring.
  15. Connect the negative battery cable.

Posted on May 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Chrysler LHS is running hot I replaced the radiator fan motor ?


Check the coolant level your water pump thermostat housing or a coolant hose or radiator is probly leaking out

Apr 25, 2015 | 2000 Chrysler LHS

1 Answer

I have a 2000 chrysler lhs and i need a diagram of the ignition coil pack as in a firing order


For just a few dollars you can get the "Haynes Automotive" manual for the L.H.S. that will have what you need, plus so much more. It is written for the average person and has all the wiring diagrams and even walks you through the engine rebuild. If you love your L.H.S. like I do mine, then it is worth the tiny, tiny investment. I would dig mine out for you but this is a better solution. You can get it online, or at ANY decent Auto Parts store. If you REALLY want me to dig mine out, hit me back and I will.

Mar 19, 2014 | 2000 Chrysler LHS

1 Answer

2000 Chrysler LHS- Key won't turn! Tried to hotwire it, but seems it's all electronic? HELP!


Well hopefully you didn't mess any of the wiring up by trying to hot wire it. But most likely the tumblers in the lock cylinder are worn out. If you replace the ignition switch it should solve the issue.

Feb 03, 2011 | 2000 Chrysler LHS

1 Answer

Replace cooling fan


To start out what way does it look like it comes out? There will be three nuts or bolts two on the top and one on the bottom it could be the other way around if you have any other questions email me at mallanapril@msn.com good luck

Apr 07, 2010 | 2000 Chrysler LHS

1 Answer

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

May 29, 2009 | 2000 Chrysler LHS

2 Answers

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


I had the same problem. My Chrysler LHS kept overheating. I had the thermostat changed out first and it didn't help. Then I had the water pump changed out and still did no good. Then changed out the radiator, still overheated. Come to find out the people that changed my thermostat put it in backwards. Evidently, the thermostats for these cars look different from all the others and people are not sure how to put them in. I took mine to a Chrysler dealer and they fixed it for me.

Apr 15, 2009 | 2000 Chrysler LHS

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

1 Answer

Replacing headlamp on 2000 lhs how to


There are two bolts that hold the assembly in place to the radiator support. Pull these (they're long bolts) and the lamp forward. That's all there is to it. I own an Intrepid and these cars are very similar.

Dec 24, 2008 | 2000 Chrysler LHS

Not finding what you are looking for?
2000 Chrysler LHS Logo

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...