Question about Ford Laser

Open Question

Head bolts ford telstar tx5 2l double overhead cam 1995

Torque settings

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

the terrier
  • 94 Answers

SOURCE: head bolts torque settings

according to the manual its 22NM or 16lb/ft

Posted on Oct 26, 2008

  • 1 Answer

SOURCE: head bolt torque specs and timing marcs for a 94 volvo 960 6cyl

you do 14 foot pounds then 45 foot pounds then a 120 degree turn.if aluminum heads are what you have

Posted on Nov 18, 2008

  • 1 Answer

SOURCE: Suzuki Vitara 1996 V6 2L assembly problems

The suzukiinfo.com site has a whole heap of free genuine manuals you can download and print out.
www.suzukiinfo.com

Posted on Jan 22, 2009

  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

  • 1033 Answers

SOURCE: torque specifications for head bolts 1995 Jetta 2.0

You should really go to an auto parts place and buy a manual. This something you really should not cut corners. It will give you the specs and the sequence of how to torque the head. You will also need to know how to set the timing in relation to the cam and crank. Manual is well worth the money. It has pictures, instructions, and such.

Good Luck

Posted on Feb 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the cylinder head torque settings for a hyundai getz 1.6 16 valve double overhead cam Engine cod G4ED


renew bolts
stage1- 30NM
stage2-90deg
stage3-individually slacken off 360deg
stage4-30NM
stage5-90deg

crank pulley bolt-142NM
cam sprocket bolt-88NM

i like to help people like you that give engine codes it makes it so much easier

Jul 20, 2016 | Hyundai Cars & Trucks

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings


Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Nov 22, 2014 | 1996 Toyota Land Cruiser

1 Answer

Torque on head bolts 3.0


This must be done in a specific sequence In THE ORDER described. It is important to know that Ford used a torque to yield tightening process. This effectively stretches the bolt to keep it tensioned. So removing these bolts means you have to throw them away...they cannot be re-used. ALWAYS use new bolts.

Follow the sequence shown in the diagram below and perform these 5 steps EXACTLY (yes, you do two quarter turns at the end):

1. Tighten all bolts to 37 lbs-ft

2. Loosen the bolts one full turn

3. Now torque all bolts to 22 lbs-ft

4. Tighten all bolts an additional 1/4 turn (90 degrees)

5. Tighten all bolts another 1/4 turn (90 degrees)


624987b1-3ab9-468a-afa8-1334b5e05368.png

Aug 31, 2014 | 2002 Ford Taurus

1 Answer

Torque specs for cylinder head on a 200 ford focus with 2.0 ltr single overhead cam. and for connecting rod... Thank you much.


  1. CAUTION: Always install new cylinder head bolts. NOTE: Lubricate the cylinder head bolts with Super Premium 5W 30 SAE X0-5W 30-QSP or equivalent meeting Ford specification WSS-M2C153-G prior to installation. Install the cylinder head assembly and tighten the cylinder head bolts in the following sequence.
  1. Tighten all bolts in a single sequence to 50 Nm
  2. Back the bolts off 1/2 turn.
  3. Tighten the bolts in sequence shown to 50 Nm .
  4. Rotate all the bolts in a single sequence an additional 180 degrees in two steps of 90 degrees each.
9 3 1 5 7
8 6 2 4 10 sequence for head


Spec for rod 38Nm

May 07, 2010 | 2000 Ford Focus

1 Answer

Could you help me with the ford escort 1600 zetec (1995) twin cam cylinder head torque settings please regards tom


Tightening sequence is (imagining the bolts looking down from the front of the car, top left to right being bolts 1,2,3,4,5 and bottom left to right being bolt 6,7,8,9,10 the tightening order is 8,3,9,2,7,4,6,5,10,1 Draw it out on paper to make it become clear. (it will I promise)
The tightening is done in stages, Stage one being to screw all the bolts in finger tight. Stage two is tightening the bolts in sequence to 20-30nm Stage three is tightening the bolts in sequence up to 40-50nm Stage four is tightening the bolts in sequence by 90-120 degrees. ---- Data checked and double checked, thats the official way to do it.


Jan 23, 2010 | 1995 Ford Escort

1 Answer

Require ford escort rs 2000 1976 torque settings head bolts


2lt overhead cam with them horrible tappet adjusters,cast iron head but valves dont hit the head if the timing belt breaks ,but it does on the 1600 .called a pinto in america .Remember the assembly line well ,have many a fond memory of working on it and the staff canteen on night shift ,what lovely grub we got.Head bolt torque is about 80lbs because i used to pull them down to check them after the machine had tightened them up

Apr 24, 2009 | 1997 Ford Escort

4 Answers

Torque wrench settings


please understand there are a lot of items on a car that require torque settings every thing from the lug nuts to every engine bolt, and transbolt. please be more specific

Jul 03, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...