Question about 1991 Isuzu Rodeo

1 Answer

Stripped threads in engine block for exhaust manifold

I have stripped threads in engine block for the exhaust manifold, how would I put a bolt in the block so I don't have a exhaust leak anymore?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

You need a heli-coil kit. Your local parts store should be able to help you find the proper size if you take the bolt with you. Follow the directions carefully and buy a new bolt for the manifold.

Posted on May 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The tork on a chevy 350 motor connecting rods


The "TORQUE" setting is below
Bolts or Parts Lube or Sealer Torque to: 7/16 Main Caps (2 bolt) Engine Oil 70 ft-lbs. 7/16 Inner Main Caps (4 bolt) Engine Oil 70 ft-lbs. 7/16 Outer Main Caps (4 bolt) Engine Oil 65 ft-lbs. 3/8 Outer Main Caps (4 bolt) Engine Oil 40 ft-lbs. Warning!!! If you are using ARP bolts, you MUST use
their specs. Click Here! 3/8 Connecting Rod Bolt Engine Oil 45 ft-lbs. 11/32 Connecting Rod Bolt Engine Oil 35 ft-lbs.

Cylinder Heads

Engine oil

(blind hole)

Sealer

(water jacket)

65 ft-lbs.
Rocker Studs (screw-in) Engine Oil 50 ft-lbs. Oil Pump Engine Oil 65 ft-lbs. Oil Pan Engine Oil 12 ft-lbs. Cam Sprocket (upper gear) Thread Locker 20 ft-lbs. Timing Cover Engine Oil 6 ft-lbs.

Intake Manifold

(Cast Iron Heads)
Non- Hardening Sealer 30 ft-lbs. Valve Cover Engine Oil 3 ft-lbs. Exhaust Manifold Anti-Seize Lubricant 25 ft-lbs. Spark Plugs No Lube or Sealer 20 ft-lbs.

Flexplate (Automatic)

Flywheel (Clutch)
Thread Locker 60 ft-lbs. Clutch Pressure Plate Thread Locker 35 ft-lbs.

Centerbolt

(Harmonic Damper)
Engine Oil 60 ft-lbs.

Bellhousing

(Transmission to Block)
Engine Oil 25 ft-lbs.

Dec 02, 2016 | Cars & Trucks

Tip

Small Block Chevy V8 267, 305, 327, 350, 400 cid.


Bolts or Parts Lube or Sealer Torque to: 7/16 Main Caps (2 bolt) Engine Oil 70 ft-lbs. 7/16 Inner Main Caps (4 bolt) Engine Oil 70 ft-lbs. 7/16 Outer Main Caps (4 bolt) Engine Oil 65 ft-lbs. 3/8 Outer Main Caps (4 bolt) Engine Oil 40 ft-lbs. 18436572 The firing order Small Block Chevy V8 3/8 Connecting Rod Bolt Engine Oil 45 ft-lbs. 11/32 Connecting Rod Bolt Engine Oil 35 ft-lbs. Cylinder Heads
Engine oil
(blind hole)Sealer
(water jacket)
65 ft-lbs.
Rocker Studs (screw-in) Engine Oil 50 ft-lbs. Oil Pump Engine Oil 65 ft-lbs. Oil Pan Engine Oil 12 ft-lbs. Cam Sprocket (upper gear) Thread Locker 20 ft-lbs. Timing Cover Engine Oil 6 ft-lbs. Intake Manifold
(Cast Iron Heads)
Non- Hardening Sealer 30 ft-lbs. Valve Cover Engine Oil 3 ft-lbs. Exhaust Manifold Anti-Seize Lubricant 25 ft-lbs. Spark Plugs No Lube or Sealer 20 ft-lbs. Flex plate (Automatic)
Flywheel (Clutch)
Thread Locker 60 ft-lbs. Clutch Pressure Plate Thread Locker 35 ft-lbs. Center bolt
(Harmonic Damper)
Engine Oil 60 ft-lbs. Bell housing
(Transmission to Block)
Engine Oil
  • 25 ft-lbs.

on Jul 17, 2010 | 1985 Chevrolet Chevy

1 Answer

How to take head off2003 Buick Lasabre


This is not easy. You need to drain the coolant. You need to unhook the battery and remove the intake manifold and the exhaust manifold. You need to remove the ignition parts and the fuel lines, you need to then remove the valve covers and the head bolts. Pry the head off the block. Check for warp on the head, clean the surfaces and reassemble, That is if nothing goes wrong. Head and manifold bolts can get stuck or break off, they can strip out the threads on the block. You are better off taking it to a shop.

Nov 18, 2012 | Cars & Trucks

1 Answer

Need head bolt torqe for 3100 and should bolts be dry


The bolts should have thread lock on them when installing, and the torque is done in 2 steps. 33 ft lbs. and then 90 deg. after that on the second pass. 3.1L Engine CAUTION
Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do not allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion. LEFT SIDE (FRONT)
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Disconnect the top half of the air cleaner assembly, then remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Disconnect the spark plug wires from spark plugs and looms then route the wires out of the way.
  7. Remove the rocker arm (valve) covers.
  8. Remove upper intake plenum and lower intake manifold.
  9. Remove the left side exhaust manifold.
  10. Remove oil level indicator tube. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  11. Remove rocker arms nut, rocker arms, balls and pushrods.
  12. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To install:
  13. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  14. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP are showing.
  15. Coat the bolt threads lightly with sealer, then install finger-tight.
  16. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  17. Install the pushrods, rocker arms, balls and rocker arm nuts in their proper locations. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  18. Install the lower intake manifold and upper intake plenum.
  19. Install the rocker arm (valve) covers.
  20. Install the oil level indicator tube. Insert the dipstick.
  21. Connect the spark plug wires to spark plugs and looms.
  22. Install the left side exhaust manifold.
  23. Install the exhaust crossover pipe and heat shield.
  24. Refill the cooling system.
  25. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  26. Connect negative battery cable.
  27. Start vehicle and verify that there are no leaks. Fig. 20: Cylinder head mounting and bolt tightening sequence - 3.1L engine 86883134.gif
RIGHT CYLINDER HEAD (REAR) CAUTION
Fuel Injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove the top half of the air cleaner assembly and remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Raise and safely support the vehicle.
  7. Detach the Oxygen (O2) sensor connector.
  8. Disconnect the exhaust pipe from the exhaust manifold.
  9. Remove the right side exhaust manifold.
  10. Carefully lower the vehicle.
  11. Disconnect the spark plug wires from spark plugs and wire looms and route the wires out of the way.
  12. Remove the rocker arm (valve) covers.
  13. Remove upper intake plenum and lower intake manifold. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  14. Remove rocker arms nut, rocker arms, balls and pushrods.
  15. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To Install:
  16. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  17. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP showing.
  18. Coat the bolt threads lightly with sealer, then install finger-tight.
  19. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  20. Install the pushrods loosely retained with the rocker arm assemblies. Make sure all pushrods are in the correct locations. Coat the ends of the pushrods with prelube. The intake rods are marked yellow and are 5 3?4 inch long. The exhaust pushrods are marked green and 6 inches long. balls and rocker arm nuts. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  21. Install the lower intake manifold and upper intake plenum.
  22. Install the rocker arm (valve) covers.
  23. Connect the spark plug wires to spark plugs and wire looms.
  24. Raise and safely support the vehicle.
  25. Install the exhaust manifold.
  26. Connect the exhaust pipe to the exhaust manifold.
  27. Carefully lower the vehicle.
  28. Connect the Oxygen (O2) sensor wiring.
  29. Install the exhaust crossover pipe and heat shield.
  30. Refill the cooling system.
  31. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  32. Connect negative battery cable.
  33. Start vehicle and verify that there are no leaks.
prev.gif next.gif

Feb 04, 2011 | 1997 Oldsmobile Achieva

2 Answers

Torque specification on a 2003 alero cylinder heads 3.4 liter


3.4L Engine To Remove:
  1. Remove the lower intake manifold.
  2. Remove the exhaust crossover pipe.
  3. If removing the right cylinder head, remove the catalytic converter from exhaust manifold.
  4. If removing the left cylinder head, remove the engine oil dipstick and tube.
  5. Remove the rocker arms and pushrods.
  6. Remove and discard the cylinder head bolts.
  7. Remove the cylinder head.
  8. Clean the mating surfaces on the following items:
    • Cylinder head
    • Cylinder block
    • Intake manifold
  9. Clean the cylinder block bolt threads.
NOTE: During disassembly, keep the valve train components together for proper location during assembly.
To Install:
NOTE: Coat the cylinder head bolt threads using thread sealer.
  1. If removed, install the following components:
    • Exhaust manifold
    • Accessory studs
    • Spark plugs
  2. Place the cylinder head gasket in position over the dowel pins. Ensure that the THIS SIDE UP note is showing.
  3. Install the cylinder head. Cylinder head torque sequence ’99-‘00 gmpc_v6_14.gif

    Cylinder head torque sequence ’01-05 gm-03-34-682.gif

  4. Install the new cylinder head bolts.
    • Tighten the cylinder head bolts a first pass to 44 ft lb (60 Nm).
  5. Tighten the cylinder head bolts in sequence an additional 95 degrees.
  6. Install the intake gasket.
  7. Install the pushrods and rocker arms.
  8. Raise and support the vehicle.
  9. Install the catalytic converter and dipstick tube and indicator if removed.
  10. Lower the vehicle.
  11. Install the exhaust crossover pipe.
  12. Install the intake manifolds.
  13. Connect negative battery cable.
  14. Fill the cooling system.

Jul 03, 2010 | 2003 Oldsmobile Alero

1 Answer

What is the torque for head screws and timing


300M, Concorde, Intrepid, LHS, 1998-2004 - Cylinder Head
Removal & Installation
2.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    NOTE Place shop rags in the openings to prevent debris from entering the engine.
    Negative battery cable Accessory drive belts Crankshaft damper Intake plenum, lower intake manifold and exhaust manifold Valve and timing chain covers Coolant connections for the cylinder heads
  5. Rotate the crankshaft until the crankshaft timing mark aligns with the timing mark on the oil pump.
    WARNING Be sure the head bolts 9-11 are removed before attempting to remove the cylinder head, the head and/or block may be damaged.
    Primary timing chain Camshaft bearing caps, gradually, in the reverse order of the tightening sequence Camshafts Cylinder head bolts in reverse order of installation starting with bolts 11-9, then 8-1 Cylinder head(s)

To install:


af080a0.jpg

Fig. Camshaft bolt tightening sequence-2.7L engine

eb0ed0f.jpg

Fig. Cylinder head bolt tightening sequence-2.7L engine
  1. Thoroughly clean and dry the mating surfaces of the head and block. Check the cylinder head for cracks, damage or engine coolant leakage. Remove scale, sealing compound and carbon. Clean the oil passages thoroughly.
  2. Place a new head gasket on the cylinder block over the locating dowels.
  3. Inspect the cylinder head bolts for necking (stretching) by holding a straightedge against the threads of each bolt. If all of the threads are not contacting the straightedge, the bolt should be replaced. New head bolts are recommended.
    WARNING Due to the cylinder head bolt torque method used, it is imperative that the bolt threads be inspected for necking (stretching) prior to installation. If the threads are necked down, the bolt should be replaced. Failure to do so may result in parts failure or damage.
  4. Lubricate the bolt threads with clean engine oil, then install them.
  5. Torque the head bolts in the sequence shown in the illustration, utilizing the following steps and tightening values:
    1. Step 1: bolts 1 through 8: 35 ft. lbs. (48 Nm).
    2. Step 2: bolts 1 through 8: 55 ft. lbs. (75 Nm).
    3. Step 3: bolts 1 through 8: 55 ft. lbs. (75 Nm).
    4. Step 4: bolts 1 through 8: plus 90 degree turn using a torque angle meter.
    5. Step 5: bolts 9 through 11: 21 ft. lbs. (28 Nm).

  6. Install or connect the following:
    Camshafts, timing chain and sprockets Water connections to the cylinder head Valve and timing chain covers Crankshaft damper and torque the center bolt to 125 ft. lbs. (170 Nm) Lower intake manifold and intake plenum Exhaust manifolds Accessory drive belts Negative battery cable
  7. Fill the cooling system to the proper level.
  8. Start the vehicle, check for leaks and repair if necessary.
continue...

Apr 11, 2010 | 2002 Dodge Intrepid

2 Answers

Need the step by step instructions and pictures on how to replace an water pump on an 2002 Oldsmobile Alero 2.4L


Removal & Installation

2.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Exhaust manifold, if equipped with n automatic transaxle Right front wheel Splash shield Water pump sprocket access plate from the timing cover

    fcd00e0.jpg

    Fig. Remove the water pump sprocket access plate from the timing cover -2.2L engine
  5. Attach Water Pump Sprocket Holding Tool J 43651to the sprocket using the access plate bolts to secure the tool to the engine front cover.
    Sprocket to water pump bolts Engine block to water pump bolt Engine front cover to water pump bolt Thermostat housing to water pump feed pipe 2 water pump to engine block bolts Water pump

    30965cd.jpg

    Fig. Water pump mounting-2.2L engine
To install:
  1. Use a threaded stud in the water pump hub to align the hub to the water pump sprocket.
    Water pump and bolts Thermostat housing to water pump feed pipe Engine front cover bolt and engine block to water pump bolt. Tighten the bolts to 15 ft. lbs. (20 Nm) 2 of the water pump sprocket to water pump bolts
  2. Remove the threaded stud.
    Last water pump sprocket to water pump bolt and tighten the sprocket bolts to 89 inch lbs. (10 Nm).
  3. Remove the tool.
    Water pump sprocket access plate to the timing cover and tighten the bolts to 89 inch lbs. (10 Nm) Splash shield Right front wheel Exhaust manifold, if removed
  4. Fill the cooling system.
  5. Connect the negative battery cable.
2.4L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    WARNING Do not rotate the flex coupling more than 4 degrees or damage may occur. Oxygen Sensor (O 2 S) electrical connector Exhaust manifold heat shield Coolant inlet housing bolt through the exhaust manifold Exhaust manifold brace-to-manifold bolt Manifold-to-exhaust pipe studs Coolant inlet housing-to-water pump cover bolt Exhaust pipe from the exhaust manifold by pulling it downward Coolant inlet pipe from the oil pan Brake vacuum pipe from the camshaft housing Exhaust manifold from the cylinder head Heater hose from the heater outlet pipe Timing chain cover and tensioner Water pump cover-to-engine bolts 3 water pump-to-timing chain housing nuts Water pump and cover assembly Water pump cover from the pump

    f9cdfa8.jpg

    Fig. Exploded view of the water pump mounting-2.4L engine
continue...

Oct 22, 2009 | 2002 Oldsmobile Alero

1 Answer

Starter motor


hi there,
shut down the engine for atleast 30 minutes to cool,the starter motor was located under beneath the engine,the pinion driver was coincide to flywheel,if you want replace starter motor,disconnect starter regulator cable, loosen two bolt on the engine starter motor holder,try to swicth starter motor on a free way that could go out on mounting space,the exhaust manifold mostly is behind the way of starter motor if hard to pull out,if necessary disconnect exhaust manifold replace exhaust manifold gasket,distortion on manifold gasket may happen after removing manifold
. pull out starter motor and replace a new one, put back also exhaust manifold if you disconnect it.
set fender covers on each fender to prevent paint damage
select the correct size open end box end wrench or ratchet, socket and extension. This procedure is much easier using the ratchet, socket and extension. Use your wrench to remove all of the manifold mount bolts. The manifold will now be free enough to access the gasket behind it
remove the old gasket using your putty knife. The gasket should come of mostly intact. Use your putty knife to remove any gasket material that remains on the engine block or the manifold. Any gasket material left on the mounting surfaces will cause leaks that inhibit engine performance coat the new gasket on both sides with a light coat of anti-seize compound. Put the new gasket in place against the block mounting surface. The anti-seize compound will hold the new gasket in place and prevent the gasket from sticking to the mounting surface, making future repairs easier.
push the manifold in against the new gasket and the block. coat the threads of your manifold bolts with a light coat of anti-seize compound. This will protect the threads on the bolt and the mounting surface. Start all manifold bolts by hand to ensure that the manifold is positioned evenly against the block. Be sure that the gasket remains lined up with the mounting holes. If the gasket slips out of position it will leak.
use your wrench or a torque wrench if required by the service manual to tighten all manifold bolts. Start the engine and check for any leaks. no leaks means you are done.
have a nice day don't forget to rate me,thanks a lot.

May 20, 2009 | 1995 Toyota Land Cruiser

1 Answer

I need a diagram of a 1995 ford escort engine


96 escort 1.9L

bb97132.gif
e0d7524.gif

Engine Components
Item Part Number Description 1 6766 Oil Filler Cap 2 6A548 (8 Req'd) Valve Cover Bolt 3 6582 Valve Cover 4 — Exhaust Manifold Shield-to-Exhaust Manifold Nut (4 Req'd) 5 9A462 Exhaust Manifold Shield 6 — Exhaust Manifold Shield Stud (4 Req'd) 7 9430 Exhaust Manifold 8 9454 Exhaust Manifold Nut 9 9448 Exhaust Manifold Gasket 10 — Exhaust Manifold Stud (Fine Thread), Short (4 Req'd) 11 — Exhaust Manifold Stud, Long (1 Req'd) 12 — Exhaust Manifold Stud (Medium Thread), Short (1 Req'd) 13 6518 Valve Spring Retainer Key 14 6514 Valve Spring Retainer 15 6513 Valve Spring and Damper, Intake 16 6C515 Valve Tappet Guide Plate Retainer 17 6571 Valve Stem Seal 18 6513 Valve Spring, Exhaust 19 12405 Spark Plug 20 6269 Camshaft Thrust Plate 21 — Camshaft Thrust Plate Bolt (2 Req'd) 22 — Cup Plug 23 6B273 Camshaft Oil Flow Control Rod 24 6K292 Camshaft Front Seal 25 6256 Camshaft Sprocket 26 6278 Camshaft Sprocket Washer 27 6K252 Camshaft Sprocket Retaining Bolt 28 6L269 Camshaft Sprocket Key (5 x 18) 29 6250 Camshaft 30 6051 Head Gasket 31 6A008 Cylinder Head to Block Dowel 32 6010 Cylinder Block 33 6507 Intake Valve 34 6505 Exhaust Valve 35 6049 Cylinder Head 36 — Intake Manifold Stud (7 Req'd) 37 17A084 Engine Lifting Eye 38 — Engine Lifting Eye Bolt (2 Req'd) 39 9439 Intake Manifold Gasket 40 — Bolt 41 9723 Accelerator Cable Bracket 42 9424 Intake Manifold 43 — Intake Manifold Nut (7 Req'd) 44 9D476 EGR Valve Gasket 45 — Exhaust Gas Recirculation (EGR) Valve Bolt (2 Req'd) 46 9D475 EGR Valve 47 — Fuel Injection Supply Manifold Bolt
(2 Req'd) 48 9F593 Fuel Injector 49 9D930 Fuel Charging Wiring 50 6786 Oil Level Indicator Tube Bracket 51 — Oil Level Indicator Tube Bracket Bolt 52 6754 Oil Level Indicator Tube 53 6750 Oil Level Dipstick 54 9D280 Fuel Injection Supply Manifold 55 — Vacuum Fitting 56 9E498 Main Emission Vacuum Control Connector 57 — Vacuum Tap 58 — Vacuum Hose 59 9B989 Throttle Position Sensor 60 — Screw and Washer 61 9F782 Throttle Position Sensor Gasket 62 — Throttle Body Bolt (4 Req'd) 63 — Idle Air Control (IAC) Valve Bolt
(2 Req'd) 64 9F715 Idle Air Control Valve 65 9F670 Idle Air Control Gasket 66 9E926 Throttle Body 67 9E936 Throttle Body Gasket 68 — Vacuum Fitting 69 — Camshaft Position Sensor Screw 70 6B288 Camshaft Position Sensor 71 8255 Water Hose Connection Gasket 72 — Water Hose Connection Bolt (3 Req'd) 73 8592 Water Hose Connection 74 8575 Water Thermostat 75 6065 Cylinder Head Bolts 76 6500 Valve Tappet 77 6K512 Valve Tappet Guide Plate 78 6564 Rocker Arm 79 6A528 Rocker Arm Seat 80 6A527 Rocker Arm Bolt (8 Req'd) 81 — Ignition Coil Mounting Bracket Bolt
(3 Req'd) 82 18827 Noise Filter Condenser 83 — Ignition Coil Mounting Bolt (4 Req'd) 84 12259 Spark Plug Wire Set 85 12029 Ignition Coil 86 12043 Ignition Coil Mounting Bracket A — Tighten to 5-12 Nm (4-9 Lb-Ft) B — Tighten to 5-7 Nm (3-5 Lb-Ft) C — Tighten to 21-26 Nm (16-19 Lb-Ft) D — Tighten to 2-10 Nm (1.5-7 Lb-Ft) E — Tighten to 8-13 Nm (6-9 Lb-Ft) F — Tighten to 40-55 Nm (30-41 Lb-Ft) G — Tighten to 16-20 Nm (12-15 Lb-Ft) H — Tighten to 20-30 Nm (15-22 Lb-Ft) I — Tighten to 8-10 Nm (6-8 Lb-Ft) J — Tighten to 8-11 Nm (6-9 Lb-Ft) K — Tighten to 23-30 Nm (17-22 Lb-Ft) L — Tighten to 20-40 Nm (15-30 Lb-Ft) M — Tighten to 4.5-7 Nm (3-5 Lb-Ft) N — Tighten to 18-26 Nm (13-19 Lb-Ft)

Feb 24, 2009 | 1995 Ford Escort

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
1991 Isuzu Rodeo Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...