Question about 2000 Mitsubishi Eclipse

Open Question

How to replace timing belt on a 2000 mitsubishi eclipse . how do i take the cover that its behind the crankshaft

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
j_del
  • 1586 Answers

SOURCE: mitsubishi eclipse convertiable timing belt change?

Typical timing belt intervals are every 60k miles. It's a very involved service to do the whole job - timing belt, timing belt tensioner, serpentine or accessory belts, water pump, thermostat, spark plugs, all fluids, all filters, brake and suspension inspection, and tire rotation. On many cars it's recommended to change the oxygen sensors as well. Quite a bit of this can be done when you want, but the first five items are critical and should all be done. And regardless of whether your manufacturer says the coolant is "lifetime", replace it - don't reuse coolant. It's cheap and it's good practice to use new coolant.

Posted on Sep 30, 2008

Ad
DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

  • 8 Answers

SOURCE: 2000 Mitsubishi Eclipse will not idle, all else OK, just repl bat

I can only offer these few ideas.

  1. The TP throttle position sensors for this year group fail often Pin 1 to Pin 4 resistance should be 3.6 to 6.3 ohms but you need to remove the two 7mm bolts that hold this sensor on the front side of the throttle body, then rotate the two bolstered center and see a change in resistance from low to high. If the resistance remains fixed, the sensor is rusted out and must be replaced.
  2. The IAC motor is mounted on th LH side (driver's) of the throttle body. It should make a clicking sound when the key is turned from Lock to Run. Pin 2 to Pin 1, Pin 2 to Pin 3, Pin 5 to Pin 4, and finally Pin 5 to Pin 6 must all have continuity at 38 to 52 ohms.
  3. Check for any vacuum leaks.
  4. Remove clean and check EGR.
  5. If this is a Cranks but will not start problem, check the owners manual for Theft Deterant UNLOCK proceedure. If there is power at the rear fuel pump relay coil and no power at the MFI/ASD front relay coil and no spark, then its the security system.

Posted on Jun 28, 2009

  • 35 Answers

SOURCE: brake light bulb Mitsubishi Eclipse Cars

look for access panels in rear hatch there will be one on each side remove those and there will be 10 ml nuts holding the light housings on remove those then you can access the lights

Posted on Jul 02, 2009

SoCalShuvit
  • 66 Answers

SOURCE: Need to replace a serpentine belt in a 2000 mitsubishi eclipse

You should be able to see the diagram for the serpentine belt when you open the hood.

Posted on Jun 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Mitsubishi Eclipse GT 2dr Hatchback 3.8l crankshaft sensor location


It's under the timing belt cover in the one oclock position compared to the crankshaft.

Jun 23, 2017 | Mitsubishi Cars & Trucks

1 Answer

Where is the water pump on my mitsubishi eclipse


the water pump is located behind the timing belt cover and is driven by the timing belt, if replacing the pump put a new belt on at the same time

Jun 27, 2014 | 2001 Mitsubishi Eclipse GT

1 Answer

Replacing crankshaft position sensor 2001 mitsubishi eclipse 2.4l


Access to the crankshaft sensor is impeded by the timing belt, which must be removed, on a 2001 Mitsubishi Eclipse 3.0L V6. -----------------------------------------------------------------------------------
Multidiag Actia

Jan 31, 2013 | Cars & Trucks

1 Answer

How do i replace the crankshaft positioning sensor on my 03 eclipse


no just remove the timing belt cover and crankshaft pulley.

Jun 12, 2012 | 2002 Mitsubishi Eclipse Spyder

1 Answer

I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?


Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Mar 22, 2012 | 1999 Mitsubishi Eclipse

1 Answer

Crankshaft position sensor location 97 eclipse turbo


1997 mitsubishielcpse turbo, CKP is mounted at front of crankshaft,behind timing belt cover

Apr 30, 2011 | Mitsubishi Eclipse Cars & Trucks

1 Answer

How do i change crankshaft pos. sensor on 2000 eclipse gt 3.0. vehicle runs fantastic but everyonce in a while engine flutters like your popping the throttle, pretty violent, check engine light came on and...


the sensor shoudl be behind the timing cover the bottom gear as teeth sometimes you can get it off without removing the gear on some 3.0 hole driled on lower side of block ,if its a chrysler engine look at bell housing they have a flywheel with holes in them the cranck sensor will be bolted somewhere around the bellhousing of trans aginst the engine

Nov 14, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

How do you replace timing belt in a 2000 eclipse gt


There are some jobs you just need a manual for. This is one of them. Go to Autozone and buy a haynes manual for your car (abot $20).

General procedure is to buy new timing belt. Make sure cylinder #1 is set at TDC. Disconnect negative battery cable. Remove engine covers to access timing belt and remove timing belt Make sure all components are properly aligned and loosen pensioner to remove old timing belt. Install new timing belt. Tension belt. Double check to ensure all components are aligned properly, replace timing belt covers and reconnect battery.

Mar 06, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Need to replace a serpentine belt in a 2000 mitsubishi eclipse


You should be able to see the diagram for the serpentine belt when you open the hood.

Jul 16, 2009 | 2000 Mitsubishi Eclipse

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

Related Topics:

373 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...