Question about 2006 Pontiac G6

1 Answer

Front wheel bearing what is specs for lug nuts after replacing bearing

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 145 Answers

A general rule of thumb in my garage is 100ft/lbs for smaller lugs like cars and 120ft/lbs for larger ones like pickups.

Posted on May 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel bearing specs on Toyota t100 1995 4 wheel drive


You tighten the nut until the wheel starts getting hard to turn, then back off the nut 1/4 turn.

Jun 18, 2015 | Toyota T100 Cars & Trucks

1 Answer

What is the torque for a front axiel nut



The front wheel bearings consist of a cartridge design and are permanently lubricated and sealed requiring no further maintenance. The bearings are preset and cannot be adjusted. If any part of a wheel bearing assembly is defective, the unit must be replaced. It is critical that the wheel hub retainer is properly tightened to 210 ft. lbs. (290 Nm) and that a new wheel hub retainer is always used. I think this is what you wanted not lug nut bot lug nuts are 75-90 lbs, please if this is what you wanted click on comments and let me know. thanks Woody. .

thanks .
Woody

Oct 10, 2014 | 2001 Mercury Cougar

1 Answer

Lug Nuts keep falling off?


This is a somewhat common problem, believe it or not. Due to lack of preventive maintenance, the wheels will sometimes work themselves loose. If caught early, the loose nuts may merely need tightening to proper torque specs to solve the problem. After a certain point, damage is done to the wheels and lugs and nuts, due to the "flapping" of the loose wheel. Past this point, parts must be checked and replaced.

Whatever you do, have the wheels and lugs checked by a competent mechanic ASAP! This is a serious safety hazard that could turn deadly on the road. Is a new wheel worth more than your life? No it isn't, you can afford it!

Sep 20, 2014 | Cars & Trucks

1 Answer

I need the torque specs for a 99 GMC sierra k1500 wheel hub bolts (bearing), and axle nut bolts (front)


hub to steering knuckle 133 ft lbs.

axle nut 155 ft lbs.

lug nuts 140 ft lbs.

May 12, 2011 | 1998 Honda Civic

1 Answer

I want to know the torque spec for a wheel bearing on an Hyundai accent 2002


front hub axle nut 162-192 ft lbs.

lug nut 66-81 ft lbs.

rear hub nut 148-192 ft lbs.

Dec 11, 2010 | 2002 Hyundai Accent

1 Answer

How do i remove the front wheel bearing?


Replacing a front wheel bearing on a front-wheel drive car is not usually very easy to do. Typically, you remove the tire and then remove the nut on the end of the drive axle. (The nut is usually pretty big - maybe 27mm as a guess. It's also very tight. The spec for this car is 120lbf, or roughly 2x as tight as a lug nut. If you don't have the right socket and breaker bar/ratchet/impact driver, go buy one.) Next, you remove the brake caliper and disk. You can then use a hammer/punch to free the end of the axle from the wheel bearing (you probably do not need to completely remove it, just budge it loose from the splines). Finally, the wheel bearing is usually just held in with ~4 bolts. If you've got the axle out of the bearing, it should come off fairly easily.

This job does usually require a few specialized tools, but is not too difficult. The hardest part is usually getting the nut off the axle and freeing the axle from the splines in the wheel hub. Just be sure to properly support the car with jack stands, because you'll be really tweaking on some of those nuts, and you don't want the car to be unstable.

Jul 18, 2009 | 2001 Pontiac Bonneville

1 Answer

I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic


Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

May 23, 2009 | 1994 Honda Civic

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
2006 Pontiac G6 Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...