Question about 1997 Isuzu Rodeo

1 Answer

Blinkers I have a 1997 Rodeo LS 2 wheel drive i have no idea where to put the flasher so i can get my blinkers and hazards working again. please help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 973 Answers

It should either be in your fuse box inside your car but most likely it will be inside the engine compartment in a black box and labeled.

Posted on May 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Chrysler Vision hazard light


on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

My blinkers are not working.I replaced fuses and flasher.My hazard lights work but my blinkers still dont.What else could I check.


are you sure you replaced the signal flasher and not the hazard flasher as they look the same.put the hazards on and check to see if it was the one you replaced.if it is then you need to located the signal flasher and replace it.if you still have the old one you replaced you can use it.

May 01, 2011 | 1997 Ford Thunderbird LX

1 Answer

My blinker lights don't work i have the new part but can't find where to put it. took off panel under steering wheel and still can't find where it goes. Help


find the fuse panel as it goes into the fuse panel where the fuses are.sometimes the hazard flasher is also in the same panel but in a different spot.put the hazards on find the flasher and replace the other one you find as this is the signal flasher.

Apr 16, 2011 | 2002 Mercury Sable

2 Answers

Hazards and blinkers not working


There are separate fuses for the turn signals and blinkers, but you should check both of them just to see if they're good.

You may have a burnt out turn signal bulb as well. I know that this sounds like an obvious answer, but a single bulb can sometimes disable the entire system because of the way that some flashers operate.

You could also have a defective turn signal/hazard light flasher. This is located under the dash board on the driver's side between the steering column and the door. You have to remove the sound insulation/kick panel (the cover on the bottom of the dash board) to reach the flasher (it is easy to remove - I don't think you even need tools).

May 16, 2009 | 1997 Pontiac Grand Am

2 Answers

97 Chevy truck blinkers not working but hazards do


Try replacing the Flasher first before spending to much money for a possible simple fix. If it's not your flasher then it could be the turn signal leaver.
Ok, this may seem stupid, but that's what they did to the blazer. They set the flasher near the middle and under the center console behind the radio.


It's to the left of the radio right behind the dash. The hazard flasher and the turn signal flasher are side by side.  It right next to the Cig lighter behind the panel. They do mark the turn signal from the hazard flasher on the plastic behind them. Turn is on the right.

Good luck and hope this helps.

May 02, 2009 | 1997 Chevrolet Blazer

1 Answer

Blinkers only work with hazard engaged


you need to replace the flasher unit which is located under the dash on the drivers side. put on the hazard flashers to make locating the unit easier (by sound)

robert

please take a moment to rate this solution

Mar 07, 2009 | 2001 Ford F150 Styleside SuperCrew

2 Answers

Turn signal


The wire under the hazard button has probably come loose. Most GMC vehicles this year range were made with a closed circuit wiring between the flashers, hazard lights, and rear defrost. Over time the wiring under the hazard button has been known to loosen. This causes the whole system to lose function. If pop out the hazard button on you center console you should be able to tighten that wire back on and the system should work again.
The same thing happened to me when I put in a new radio. I bumped the wires off and my blinkers, rear defrost, and hazard lights went out. I replaced the fuses and the flasher relay but nothing. Then I asked a mechanic and he told me what I just told you.
Hope it helps!

Nov 04, 2008 | 1997 Geo Prizm

2 Answers

1997 Ford Taurus Blinker Lights


Relay or Flasher unit will be located in or near the fuse box,,,your owners manual will tell you where it is,, they are easy to replace, and cheap to buy.

Sep 26, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
1997 Isuzu Rodeo Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...