Question about 2007 Chevrolet Cobalt Coupe

1 Answer

How do you take off the oil pan on a 2007 chevy cobalt? I have removed all the bolts that secure the oil pan, but it will not come off.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 509 Answers

There is a gasket between the engine and the oil pan. It is probably stuck. You will have to pry it loose with a screwdriver. It may damage the gasket so you might have to get a new one. Make sure you scrape off the old gasket before installing the new one.

Posted on May 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the oil pump on 2007 chevy 4.8


Remove oil pan.
Mark and Remove distribuator.
Remove bolts to oil pump and remove.
Install new oil pump.
Reinstall oil pan with new gaskets.
Put in new engine oil.
With a large straight screwdriver. Rotate oil pump (clockwise for top) through the distribuator hole until a huge anount of resistance is felt.
Reinstall distribuator where marked. ( you may have to rotate tang on oil pump to get distribuator to go down. .

Start and run.

Jul 01, 2014 | Cars & Trucks

1 Answer

How do i change the oil in a 2006 chevy cobalt ?


Put car on ramps. On the lowest point of bottom of the motor, you will see a bolt. . Place drain pan under the bolt, and turn bolt all the way out. Drain all the oil out and re measure what you're putting back in. Place 3 and one half liters back in as the filter holds almost a half a liter. Try not to run the car as you may hurt valve seals air filters etc.Good luck let me know how you make out. Please rate this solution Cheers from Nova Scotia!!

Jan 13, 2013 | 2006 Chevrolet Cobalt LT

2 Answers

When does the oil pan gasket need to be replaced ?


Check this Oil Pan Removal & Installation...

2.0L & 2.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and support the vehicle.
  3. Drain the engine oil.
  4. Remove the engine drive belt.
  5. On the 2.0L engine, remove the intercooler pump bracket bolts from the oil pan.
  6. Remove the lower A/C compressor bolt from the oil pan.
  7. Remove the oil pan bolts.
  8. Remove the oil pan.
To install:
  1. Make sure that the oil pan and mounting surface on the lower crankcase are free of all oil and debris.

2_10_2012_7_06_27_pm.gif

Fig. Apply a 2mm bead of GM P/N 123785251 (Canadian P/N 88901148) around the perimeter of the oil pan and the oil suction port opening-2.0L, 2.2L, & 2.4L engines

  1. Apply a 2 mm bead of GM P/N 123785251 (Canadian P/N 88901148) around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install the oil pan.

2_10_2012_7_07_34_pm.gif
Fig. Oil pan bolt torque sequence-2.0L, 2.2L, & 2.4L engines
  1. Install the oil pan bolts in sequence. Tighten the oil pan bolts to 18 ft. lbs. (25 Nm).
  2. Install the A/C compressor bolts. Tighten the bolts to 18 ft. lbs. (25 Nm).
  3. On the 2.0L engine, install the intercooler pump bracket bolts. Tighten the bolts to 18 ft. lbs. (25 Nm).
  4. Install the engine drive belt.
  5. Lower the vehicle.
  6. Fill the engine oil to the proper level.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 10, 2012 | 2006 Chevrolet Cobalt

1 Answer

How do i remove the oil pan on a 2005 chevrolet cobalt


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and support the vehicle.
  3. Drain the engine oil.
  4. Remove the engine drive belt.
  5. On the 2.0L engine, remove the intercooler pump bracket bolts from the oil pan.
  6. Remove the lower A/C compressor bolt from the oil pan.
  7. Remove the oil pan bolts.
  8. Remove the oil pan

Dec 29, 2011 | Chevrolet Cobalt Cars & Trucks

1 Answer

How do i remove 2008 cobalt oil pan?


  1. Raise and support the vehicle.
  2. Place a drain pan under the oil pan drain plug.
  3. Remove the oil pan drain plug.
  4. Drain the engine oil.
  5. Remove the engine belt
  6. Remove the lower AC compressor bolt.Remove the 4 oil pan to transaxle bolts (1).
  7. Remove the oil pan bolts.

Jun 17, 2011 | Chevrolet Cobalt Cars & Trucks

1 Answer

What is involved with replacing the oil pan on 1998 GMC Sierra?


  • Step 1 Raise the truck using the proper equipment. Use a ramp or a jack and jack stands to support the vehicle securely by following all directions for use provided by this equipment's manufacturer.
  • Step 2 Drain all oil from the Silverado by placing an oil drip pan under the vehicle's engine block, directly under the oil drain plug. The drain plug is located on the oil pan, between the vehicle's tires underneath the vehicle. Use a wrench to loosen and remove the plug allowing the oil to drain into the pain below.
  • Step 3 Notice the various items attached to the oil pan or in the way of the oil pan dropping. For the oil pan to drop, remove the negative battery cable, front differential (only for four-wheel drive vehicles) and the under body shield by using a wrench or socket set.
  • Step 4 Remove the oil pan shield by loosening the four bolts holding it in place along the edges of the shield. Then, remove the cross brace, oil filter, the transmission to oil pan bolts and the oil level sensor.
  • Step 5 Follow the removal of those pieces by removing the bolts from the two front wiring harness, the engine wiring harness retainer, engine oil cooler pipe to oil bolts and the transmission oil cooler pipe retainer using a wrench. Located the closeout covers and bolts located on each side of the engine and remove them.
  • Step 6 Disconnect each of the oil pan bolts using a wrench that will allow the oil pan to drop. The oil pan gasket will also fall off and replacement should occur before reinstalling the oil pan.


  • Read more: How to Drop the Oil Pan in a Chevy Silverado | eHow.com http://www.ehow.com/how_4508109_drop-oil-pan-chevy-silverado.html#ixzz0wi82Ul2u

    Aug 15, 2010 | GMC Sierra 1500 Cars & Trucks

    1 Answer

    Changing the tramission filter on a 2007 Saturn Vue Hybrid


    Hello and welcome. here is the instructions for removing the trans filter. you will need to drop the bottom trans pan off to gain access to the filter.


  • Remove the oil pan bolts from only the front and the sides.
  • Loosen the rear oil pan bolts about 4 turns.
  • Lightly tap the oil pan with a rubber mallet or pry in order to allow the fluid to drain.
  • Remove the remaining oil pan bolts.
  • Remove the oil pan.
    Install the oil pan attaching bolts.
    Tighten
    Tighten the bolts to 12 N·m (106 lb in).
    c00c848.gif618143d.gif

    Aug 13, 2010 | 2007 Saturn VUE Green Line

    1 Answer

    How to change oil on a 2007 chevy tahoe


    YOUR OILPAN DRAINBOLT IS ON THE ENGINE OIL PAN. THE FILTER IS ON THE ENGINE ITSELF NOT THE PAN

    Aug 01, 2010 | 2007 Chevrolet Tahoe

    1 Answer

    I need bolt torque specs for a 2006 chevy cobalt Rod bolt and pan bolt torque specs also oil clearance for rod journals


    if you just go to a mecanic and ask what are the specks on that they should know but i think if you just tighten them down with an impact wrench till it is really tight after ou start the car it will run like **** then it will work its self out

    Nov 17, 2009 | 2006 Chevrolet Cobalt

    1 Answer

    My oil pan is cracked and I want to know if I have to remove the engine to change this.


    If you can see and get to all of the bolts which hold the oil pan to the bottom of the engine and if it appears obvious that the oil pan can be removed without being blocked by anything else, then you don't have to remove the engine. Come to think of it, I don't think that I have ever seen a car where you had to remove the engine in order to remove the oil pan.

    Apr 20, 2009 | 2005 Chevrolet Cobalt

    Not finding what you are looking for?
    2007 Chevrolet Cobalt Coupe Logo

    289 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6918 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...