Question about 1996 Nissan Maxima

1 Answer

I had my 1996 nissan maxima sent in for inspection only to fail because the O2 sensor and catalyst sensor were not ready as were two other sensors how do i correct this problem

Posted by on

Ad

1 Answer

Assuming you need to ask. You will need to go to a repair shop,that has experience with your type of vehicle

Posted on May 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No no it wasn't because of the O2 sensor that it didn't pass it was a couple of things that came up and the we're Catalyst not ready Monitor Evap not ready Monitor O2 not readyz


You have 8 I/M or Emission Monitors that have to run clear
BEFORE you can go to inspection

Your Catalyst Efficiency comes from the switching comparison
of the front & rear oxygen sensors being out of range

Until you resolve the rear O2 Sensor Heater Issue you won't
know if the cat is good or you have other problems

You need professional scan tool software & a long road test
to even find a problem,then component test,which apparently
wasn't done when they hung the new rear sensor on based on a code

Apr 30, 2014 | Cars & Trucks

2 Answers

P-0051 TROUBLE CODE


This is a generic OBD2 code for a defective O2 Sensor, your car will most likely have 2 sensors, one narrow band (cheaper one) and one wide bans (dearer one).
It's usually the wide band sensor that fails and can be found just past the catalytic converter.

Mar 05, 2012 | 2003 Nissan Maxima

1 Answer

Will a bad knock sensor cause a misfire. car is missing change the plugs no help codes are misfire and knock senser sometimes a #2 o2 sensor. 1999 maxima thanks for your help.


A Bad Knock Sensor will not cause a misfire, unless the advance is off due to a faulty Knock Sensor. The O2 Sensor will cause a random misfire.

Good luck on this repair.

Jan 21, 2011 | 1996 Nissan Maxima

1 Answer

I have a 1996 saturn wagon. it failed on omissions for egr. ox sensor and catalyst. I had a new egr.. o2 sensor.. oxygen sesor before catalyst.. drove car on many different drive cycles and over 4-600...


You need to read the codes that your check engine light is showing. Go to Autozone or any place like that and they can read the codes for free. Throwing parts at a car doesn't fix it but finding the source of the problem and then repairing as necessary will allow for better results. Going off the check engine light being on can mean it is anything.

You have two O2 sensors on your car. One just after the head on the header. This is the O2 sensor that tells the PCM what the air/fuel is and the PCM can adjust accordingly. The one BEHIND the catalytic converter (or cat for short) does nothing but tell the PCM that the cat. is working properly. You may be changing the wrong O2 sensor. Also the EGR could be an electrical problem if that is the cause of the emissions failure.

So to review, find out the codes, post back with the codes and everything can go from there.

Feb 26, 2010 | 1996 Saturn SL

3 Answers

I failed the emisson's test. I have a 97 Nissan


P0136 indicates a bad O2 sensor. This reports poor emission performance back to the car's PCM (computer)
P0325 indicates a bad "Knock" sensor which would adversely effect drivability as far as performance is concerned. Only way to fix these 2 problems is replacement of the 2 components.

Nov 03, 2009 | 1997 Nissan Maxima

3 Answers

Knock sensor 1996 v6 3.3 nissan pathfinder


The Crankshaft Position Sensor is located: Under hood, driver side, front engine area, mounted rear of crankshaft pulley
The Knock Sensor is located: Under hood, center, front engine area, below intake manifold, mounted on block

Jun 14, 2009 | 1996 Nissan Maxima

1 Answer

1996 Nissan Maxima oxygen sensor


hye there ,,there are 3   o2 sensors on your car,,one for each bank,,,and the 3rd sensor is located after the cat this one usually goes first,,,,just make sure you no if your cars an import or not as they can be different,,,then you should be safe when ordering ,,hope that helps,,,

Apr 24, 2009 | 1996 Nissan Maxima

2 Answers

Catalyst Efficiency Below Threshold (Bank One)


what is catalyst efficiency below threshold ( bank 1 ) mean?

Dec 12, 2008 | 2005 Nissan Maxima

Not finding what you are looking for?
1996 Nissan Maxima Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

78238 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...