Question about 2000 Jeep Grand Cherokee

1 Answer

What should the thermostat setting be on a 2000 jeep cherokee with a 4.0 litre 6 cylinder motor.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

You can't set a thermostat but you should only use a 195 degree(f) or the engine sensors will think the engine has not warmed up.

Posted on May 27, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
joecoolvette
  • 5660 Answers

SOURCE: What is the tension on cylinder head bolts for a

Would like to state the cylinder head Torque Values, Torque Pattern, and Tightening Sequence, plus additional tips.
[I know it's more than you asked for, but after you read the entire answer here, I believe you'll know why I stated it this way]

Torque Pattern:
Top of head starting from Left going Right,
8, 4, 1, 5, and 9
Bottom of head, (Exhaust manifold side), starting from Left going Right,
7, 3, 6, 2, and 10

You're supposed to use old bolts with the head cut off, (Alignment Dowels), in bolt holes 8 and 10. This way you goop the gasket, and install it, then slide the head on. Place the head bolts in, SNUG them down. Remove those alignment dowels. Then put bolts 8 and 10 in place.
After the head of the bolt is cut off, you saw a slot in the top of the bolt. Helps when you remove it. (Have any old bolts that are long enough for this, and have the correct threads?)

=>Coat No.7 bolt with thread sealant.

Tightening Sequence:
Step 1: Tighten all bolts to 22 Foot Pounds. (30Nm) (Using the above Torque Pattern)

Step 2: Tighten all bolts to 45 Foot Pounds. (61NM)

Step 3: Tighten 1 Through 6 <- to 110 Foot Pounds. (149Nm) DO NOT TIGHTEN No.7 bolt yet!

Step 4: Tighten No.7 bolt to 100 Foot Pounds. (136Nm) DO NOT TIGHTEN further! It only tightens to 100 Ft.Lbs. (136Nm)

Step 5: Tighten bolt 8 Through 10 to 110 Foot Pounds. (149Nm)

Step 6: Repeat Steps 3 , 4, and 5


Posted on Sep 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fireing order diagram


cylinder firing order is: is 1-5-3-6-2-4 .... In Jeep Grand Cherokee Laredo ...Happy motoring.

Sep 04, 2014 | 1996 Jeep Grand Cherokee

1 Answer

What motor or motors came in the jeep cherokee in 1985 in the US.


1985 Jeep Cherokee came with either a 4 cylinder 2.5L with a 1 barrel carb or a 6 cylinder 2.8L with a 2 barrel carb. The 4WD only had the option of a 4 cylinder 2.1L turbo Diesel.

Jan 21, 2011 | 1985 Jeep Cherokee

1 Answer

I'm trying to locate the thermostat on my 2000 jeep grand cherokee


  1. On 2000 Jeep Grand Cherokee 4.7L V8
  2. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  3. Remove thermostat housing mounting bolts, thermostat housing and thermostat.

2000 Jeep Grand Cherokee 4.0l v6
Note:on the In-line 6 4.0L model the thermostat housing is mounted at the top of the engine block next to the water pump.

Nov 14, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Jeep 4.0 firing order


1999 Jeep Cherokee 4WD 4.0 liter L6 VIN "S"

71cf96f.gif

Hope this helps (remember rated this).

Aug 09, 2010 | 1998 Jeep Cherokee

2 Answers

Jeep 242 cid,4.0 litre engine diagram


No absolutely sure on exactly what you need on the "engine diagram".
Most people need to know what the Cylinder Numbers are.
Let me know with a more specific question (done on the Comments section of this Posting) and I'll get back with you.

For the 4.0L L6:

Firing Order:
1-5-3-6-2-4

Cylinders:
(back)
..6
..5
..4
..3
..2
..1
(front)

Coils Paired:
Cylinder 1 with Cylinder 6
Cylinder 2 with Cylinder 5
Cylinder 3 with Cylinder 4

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


Mar 22, 2010 | 2000 Jeep Grand Cherokee

1 Answer

What is the firing order of a 2005 jeep grand cherokee


I wrote all engine spec for a 2005 jeep grand cherokee

3.7L 6 cylinder
1-6-5-4-3-2

4.7L 8 Cylinder
1-8-4-3-6-5-7-2

5.7L 8 Cylinder
1-8-4-3-6-5-7-2

let me know if this help you.....

Sep 30, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Jepp Cherokee 2000 4.0 L 123K miles, cylinder #6


try changing your crank senor. Get part from the dealer... My jeep was misfiring and changed OEM part and jeep rides good.

Apr 27, 2009 | 2000 Jeep Cherokee

1 Answer

Forgot where spark plug leads go


front to back cylinders are 1 2 3 4 5 6 on your cap there should be a #1 going clock wise here is the firing order 1 5 3 6 2 4

Feb 15, 2009 | 1996 Jeep Grand Cherokee

1 Answer

1994 jeep cherokee starting problem


it is the crankshaft sensor try that and i bet youll get it

Jul 04, 2008 | 1994 Jeep Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...