Question about 1995 Ford Econoline

Open Question

Trouble code 212 ford econoline van 1995 e-150 loss of ignition diag. monitor input to spark output cicuit grounded whats this

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
fixincars
  • 335 Answers

SOURCE: ford f-150 econoline triton v-8

How soon after it starts does it shut off?

Posted on Aug 14, 2008

Ad
samson-1
  • 153 Answers

SOURCE: freeze plugs ford econoline 150

The freeze plugs can be fixed with the engine in the veicle. There are some rubber plugs available that have a bolt thru the middle. Pry out failed plug, push in rubber replacement, tighten bolt to expand rubber. Fixed.

Posted on Oct 25, 2008

  • 18 Answers

SOURCE: Where is my fuse box?

It should be under the hood. Near the battery

Posted on Jan 15, 2009

mnabi01
  • 94 Answers

SOURCE: where is the fuel pump

the switch is located under passenger side foot trim panel under glove box. open passenger side door and remove the plastic cover .

Posted on Jan 28, 2009

emissionwiz
  • 76118 Answers

SOURCE: where is the speed sensor on a 1995 Ford econoline van

the sensor is located on the driver side of the transmission case

Posted on Jun 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS THE 1994 FORD ESCORT AIRBAG CODE 34 REPAIR


Ford Airbag Fault Codes
Flash Code Component/Fault Description
- No Air Bag Indicator - Inoperative Indicator Circuit
- Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor
Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 Right Radiator Primary Crash Sensor Feed/Return Circuit Open
42 Left Radiator Primary Crash Sensor Feed/Return Circuit Open
44 Right Radiator Crash Sensor Not Mounted to Vehicle Properly
45 Left Radiator Crash Sensor Not Mounted to Vehicle Properly
51 Airbag diagnostic Monitor Internal thermal fuse Blown
52 Back-up Power supply Voltage Boost Fault
53 Front Crash Sensor High Resistance or Diagnostic Monitor Failure

Aug 12, 2014 | 1994 Ford Escort

1 Answer

1989 Ford Econoline 150 Van will not start


Most all vehicles have main power cable to starter solenoid which is mounted on the starter where the power cable to the switch connects OR there is a separate heavy gauge red wire connected to the positive post of the battery that leads to the ignition switch. Also check your ground cable by connecting battery jumper cable to negative post on battery and other end to metal frame of van.

May 22, 2017 | Ford Econoline Cars & Trucks

1 Answer

My 1989 ford econoline e-150 (small v-8) won't run after charging battery


Well I was going to ask if you have checked the alternator output, but the part about the ignition switch makes me wonder if the switch is failing. It could be damaged internally and not up to the task of carrying voltage when everything is turned on.
I would still check alternator output at the alternator and at the battery.
You should have 14 volts at idle with all accessories off.

Jan 09, 2013 | Cars & Trucks

1 Answer

1992 ford taurus ignition loss from eec to spark output grounded


This means that the Comprehensive Component Monitor (CCM) monitors the operation of the fuel injector drivers in the PCM. The test fails when the fuel injector does not operate electrically even though the harness assembly and fuel injectors test satisfactorily.


Faulty fuel injector driver within the PCM could be the cause.

Aug 23, 2012 | 1992 Ford Taurus

1 Answer

How to change spark plugs on 5.4l


Your van uses a coil on plug ignition system. Use the following procedure to change the plugs.

  1. Remove the engine cover and air cleaner assembly.
  2. Disconnect the ignition coil electrical connector.
  3. Remove the ignition coil mounting bolt.
  4. Remove the ignition coil.
  5. Remove the spark plug.


tecnovative_21.gif

Jan 13, 2011 | 1999 Ford Econoline

2 Answers

Is there a OBD on a 1992 ford econoline,if there is,where is it located?


Your van does not have OBD, but it does have a EEC-IV and MCU connector sit under the hood near the battery, will have a cover over the connector small black cover will read on it (diag. connector).Hope this was very helpful.

Mar 31, 2010 | 1992 Ford Econoline

2 Answers

What is airbag light code 31 and 51 on a 1994 ford taurus


I was unable to locate code 31 in my book here is a copy of the codes. looks like you just need a fuse for #51. this may fix 31 as well.

Diagnostic Trouble Code Table 1994

AIR BAG DIAGNOSTIC MONITOR DIAGNOSTIC TROUBLE CODE PRIORITY TABLE
Priority Code Component/Fault Description
Highest - No Air Bag Indicator - Inoperative Lamp Circuit or No Ignition
Voltage to Air Bag Diagnostic Monitor

Continuous Air Bag Indicator - Air Bag Diagnostic Monitor
Disconnected or Inoperative
12 Low Battery Voltage
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Safing Sensor Not Mounted to Vehicle Properly
22 Safing Sensor Output Shorted to Battery Voltage
23 Safing Sensor Circuit Input Feed/Return Circuit Open
24 Safing Sensor Output Feed/Return Circuit Open
32 Driver Side Air Bag Module High Resistance or Open
33 Passenger Side Air Bag Module High Resistance or Open
34 Driver Side Air Bag Module Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Module Low Resistance or Shorted
42 Center Radiator Primary Crash Sensor Feed/Return Open
44 Center Cowl Primary Crash Sensor Not Mounted to Vehicle Properly
45 Center Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
51 Diagnostic Monitor Internal Thermal Fuse - Fuse Blown Due to
Intermittent Short to Ground
52 Backup Power Supply - Voltage Boost Fault
53 Primary Crash Sensor Circuits - Resistance to Ground or Air Bag
Diagnostic Monitor Failure

Lowest - Rapid Continuous Flashing of Air Bag Indicator (No DTC) All Primary

Sep 30, 2009 | 1994 Ford Taurus

2 Answers

1996 Ford E150 econol, 5.8 L 351 Stalls sporadically, runs great.


Did you check your fuel pump to see if it is functioning right or not .

Sep 16, 2009 | 1989 Ford Econoline

2 Answers

My air bag light on my 2000 Ford Econoline van flashes a 19 code. Does anyone know what that means?


Seems to be a very common problem with Ford. The wiring harness beneath the drivers seat contains the sensors for the airbag system. Go under the drivers seat and secure all the wires and clips. This makes most error lights for the airbags go away. Hope this helps and good luck!

May 02, 2009 | 1996 Ford Aerostar Extended

1 Answer

I have 3 codes that showed up in the computer of my 1995 Ford Windstar


Here is the first half of the codes look till you find the one you have
111 System PASS.
112 ACT sensor circuit grounded.
113 ACT sensor circuit open.
114 ACT sensor is out of Self-Test.
116 ECT sensor is out of Self-Test.
117 ECT sensor circuit grounded.
118 ECT sensor circuit open.
121 TP sensor is out of Self-Test.
122 TP sensor input is less than Self-Test minimum.
123 TP sensor input is greater than Self-Test maximum.
124 TP sensor input voltage is greater than expected.
125 TP sensor input voltage is less than expected.
128 MAP vacuum hose damaged or disconnected.
129 Insufficient MAF input.
136 HEGO sensor circuit indicates system lean (Right HEGO).
137 HEGO sensor circuit indicates system rich (Right HEGO).
139 No HEGO switching (Front Side).
141 Fuel system indicates lean.
144 No HEGO switching (Left Side).
157 MAF sensor circuit open.
158 MAF sensor shorted to power.
159 MAF sensor is out of Self-Test.
167 Insufficient TP input change.
171 Lack of HEGO switching (Rear Side).
172 HEGO sensor circuit indicates lean. (Rear Side).
173 HEGO sensor circuit indicates rich. (Rear Side).
174 Check for diluted engine oil.
175 Lack of HEGO switching (Front Side).
176 HEGO sensor circuit indicates lean. (Front Side).
177 HEGO sensor circuit indicates rich. (Front Side).
178 Check for diluted engine oil.
179 Fuel system at part throttle lean adaptive limit, system rich (Rear Side).
181 Fuel system at part throttle rich adaptive limit, system lean (Rear Side).
182 Fuel system at idle lean adaptive limit, system rich (Rear Side).
183 Fuel system at idle rich adaptive limit, system lean (Rear Side).
184 MAF sensor input voltage is greater than expected, in range.
185 MAF sensor input voltage is less than expected, in range.
186 Closed loop injector pulse width longer than expected.
187 Closed loop injector pulse width shorter than expected.
188 Fuel system at part throttle lean adaptive limit, system rich (Front Side).
189 Fuel system at part throttle rich adaptive limit, system lean (Front Side).
193 Flexible Fuel sensor circuit failure.
211 PIP circuit failure.
212 Loss of tachometer/IDM input.
213 EEC SPOUT circuit open.
214 CID circuit failure.
215 PCM detected coil 1 primary circuit failure.
216 PCM detected coil 2 primary circuit failure.
217 PCM detected coil 3 primary circuit failure.
218 Loss of ignition diagnostic monitor signal-left side.
219 Spark timing defaulted to 10 degrees, spark output circuit open.
221 Spark timing error.
222 Loss of ignition diagnostic monitor signal-right side.
223 Loss of dual plug inhibit control.
224 PCM detected coil 1, 2, 3 or 4 primary circuit failure.
225 Knock not sensed during dynamic response test KOER.
226 Ignition diagnostic monitor signal not received.
232 PCM detected coil 1, 2, 3 or 4 primary circuit failure.
238 PCM detected coil 4 primary circuit failure.
241 Ignition control module to PCM ignition diagnostic monitor pulse width transmission error.
244 Cylinder Identification circuit fault present when cylinder balance test requested.
311 Secondary air injection system inoperative during KOER self-test (bank #1).
312 Secondary air injection system misdirected during KOER self-test.
313 Secondary air injection system not bypassed during KOER self-test.
314 Secondary air injection system inoperative during KOER self-test (bank #2)
326 PFE sensor circuit voltage lower than expected.
327 PFE sensor circuit voltage below Self-Test minimum.
328 Exhaust gas recirculation valve position sensor closed voltage lower than expected.
332 Insufficient EGR flow.
334 Exhaust gas recirculation valve position sensor closed voltage higher than expected.
335 PFE sensor circuit voltage out of Self-Test range.
336 PFE sensor circuit voltage higher than expected.
337 PFE sensor circuit voltage above Self-Test maximum.
338 Engine coolant temperature lower than expected (thermostat test).
339 Engine coolant temperature higher than expected (thermostat test).
341 Octane adjust service pin open.
381 Frequent A/C clutch cycling.
411 Cannot control RPM during KOER low RPM check.
412 Cannot control RPM during KOER high RPM check.
415 Idle Air Control system at maximum adaptive lower limit.
416 Idle Air Control system at upper adaptive learning limit.
452 Insufficient input from VSS.
453 Servo leaking down.
454 Servo leaking.
455 Insufficient RPM increase.
456 Insufficient RPM decrease.
457 Speed control command switch(s) circuit not functioning.
458 Speed control command switch(s) stuck/circuit grounded.
459 Speed control ground circuit open.

Jan 15, 2009 | 2001 Ford Windstar

Not finding what you are looking for?
1995 Ford Econoline Logo

Related Topics:

408 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...