Question about 2000 Dodge Caravan

Open Question

The driver's seat is broken in my Dodge Grand Caravan 2000

The handle that controls the back rest of the seat is broken and the whole seat is loose and cannot be kept in an upright position

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: 2000 Dodge Grand Caravan Body Squeaks

Check front stabilizer bar bushings.

Posted on Dec 21, 2008

chrishaefner
  • 1 Answer

SOURCE: 2005 dodge grand caravan. I need to work on the

Remove the 3 screws in the plastic sheilding on each side of the seat (front corner, middle side and back corner (under a little bit of carpet)). This will make it easier to get to the four bolts that hold the seat cushion base to the motor frame. There are a handful of electrical connections running from the base to the seat and then to other points (2 to the seat belt area, 1 to the base of the seat and 2 to the bottom of the seat frame near the right rear corner). None of these will prevent the motors from operating.

Posted on Oct 15, 2011

  • 3 Answers

SOURCE: HOW TO REMOVE 2000 DODGE CARAVAN REAR SEAT

There are 2 handles on the back of the seat where it attaches to the floor. If you hold the button on the handle and push it down it should release the seat from the floor. After this it just rolls out the back. Same for the middle seat if you need to remove it.

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: removing a discovery 1 head rest the handle type

The headrest is hold by the two bars of the middle. The bars are engaged in two plastic guides fitted in the seat frame. The bars are locked by two little springs located in theses guides. They are very difficult to remove under the seat foam. The solution I used is a hammer (quite heavy) with a T bar from a sockets set . The diameter was exactly the same as the inner diameter of the plastic guide . Then I inserted this bar at the bottom end of the plastic guides and I hit the bottom of the mettalic bars with these tools and I managed. After the inspection, the springs were bended and I had to give the former shape they had before the removal.
Good luck ( sorry for my poor english but I'm french!)

Posted on Apr 19, 2009

alicantecoli
  • 22095 Answers

SOURCE: My rear door, hatch, won't open. The handle is

get a machanic to have a look because it sounds like either something is broken or most likely its just loose

Posted on Jun 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver's car seat back will not lock in upright position


Mechanism most likely broken . I had a Hyundai and was rear ended and the mechanism broke plus I know of several other seat backs that broke on people

Jun 06, 2016 | 2009 Honda Accord

1 Answer

Bmw 3 series 1996 Upolsterer had seat back off & now wont lock in upright possision


The gears for the recliner has been misaligned/broken. Disassemble and look for broken parts. Refer to service manual to realign,

Jul 20, 2014 | 1996 BMW 3 Series

1 Answer

Drivers seat won't latch


Will it latch if you push the release handle down, you know opposite of trying to get it to release? It might be a broken or dislodged retaining spring that pulls downward pressure on the release handle. If this is not the problem then the teeth on the gear that the release handle engage are possibly worn out.

Apr 22, 2013 | 1999 Toyota Camry Solara

1 Answer

Chevy uplander back seat wont go up


Remove the entire seat from the truck and then remove seat cover and replace the broken part(s)

Jan 31, 2013 | 2007 Chevrolet Uplander

1 Answer

2006 Ford Explorer: Back seat won't fold flat to create flat cargo area. It folds down but not flush.


Okay so im just going to start from the seat being upright in a normal riding position.

1. You need to fold the head rests first. Pull the black tab under both headrests. They should spring into a folded position.

2. pull the side seat lever (on the door side of the seat). This will fold the top/back support down to an angle.

3. There is one more lever on the backside of this seat. Its in plain sight on the angled portion of your seat. Lift the big plastic lever.

4. While keeping the handle lifted, grasp the back of the seat and pull it torwards the front of the car. The seat should come unlocked and roll forward and down more towards the floor. If you have a bunch of junk on the floor, it obviously wont work. clear the path and the seat will fold completely flat.

Also, your drivers seat and front passenger seat cannot be all the way back, they need to come forward some in order for the second row seats' head rests to clear and fold flat.

Oct 02, 2010 | 2006 Ford Explorer

1 Answer

How do you lay down rear seat 2001 coerokee larado


Start with removing the head rests. There is a handle on each one on the backside. push the handle and lift the headrest up till it comes out. You'll find a handle looking appr. 1" out of the seat, you'll see it near the door at the hind quarter of the seat. Pull the handle up and the seat will lift and swing. Swing them up to upright position. at the bottom of the backseat, back upholster you find another handle on each inner wheel cover. press them back wards and pull the seat back down.

Oct 21, 2009 | 2001 Jeep Grand Cherokee

1 Answer

My driver seat back snapped and will no longer stay in the upright position. The bottom (****) part operates fine.


There is a pin near the hinge that is supposed to catch and then latch your seat into an upright position. If this has come loose, simply engage it again and tighten it. If it is broken, you'll be looking to take to the shop and either get it wielded (not with the trouble and in some states reputable shops won't do it for crash test safety reasons) or have the seat replaced (the best and safest option).

Jun 06, 2009 | 1998 Honda Accord

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge...


the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.
  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in the upright position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Mar 02, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
2000 Dodge Caravan Logo

Related Topics:

573 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...