Question about Mercury Capri

1 Answer

Crank position sensor, and ignition module location

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

FOR EXACT LOCATION I NEED THE YEAR MAKE & MODEL

CRANK SENSOR IS NORMALY NEXT TO THE LOWER PULLEY

CAM SENSOR IS CENTER WAY UP FROM THAT

Posted on Jun 05, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 50 Answers

SOURCE: crank position sensor location

you will need to remove the starter to gain acess to the ckp sensor. once you remove the starter look on the engine block and you will see the sensor. The only problem with doing this repair yourself is that you will not be able to preform the crankshaft position variation learn procedure with out a factory scan tool. The vehicle may crank an run, but the timing advance curves will be wrong so the vehicle will probably cut off every time you remove your foot from the gas pedal. Hope this info helps!

Posted on Aug 18, 2008

  • 1 Answer

SOURCE: 96 jeep grand cherokee 4.0

change the computer .... PCM get a used one it fixed mine had same problem

Posted on Feb 19, 2009

  • 398 Answers

SOURCE: 1997 Dodge Intrepid cranks over won't fire

well first i can tell you to check your grounds from the battery for corrosion , it can be inside the cables also. next check out all the work you just did, make sure all electrical connections are tight, plug wires etc, any thing you touched.do the lights work fine when you try to turn it over? It could be alternator. if it turns the crank then it has to be an electrical problem. i will give you more ideas when they come to me.

Posted on Mar 16, 2009

  • 383 Answers

SOURCE: jeep wrangelr Crank Position Sensor

wall5552: there were two engines used in 1992 Jeep Wranglers.
A 2.5 liter and a 4.0 liter. HOWEVER>>>> The location for the crank angle sensor is the same for both.
It is located on the bell housing up near the front at about the 10:00 PM position.
The Cam position sensor is located in the Distributor on both engines as well.

Posted on May 10, 2009

  • 407 Answers

SOURCE: crank position sensor location

should be on bell housing on thr driver side

Posted on May 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of ignition module for 1998 Lincoln town car executive edition


Doesn't have ignition module . What is the problem , no spark ? Crankshaft position sensor . The PCM - powertrain control module controls the coil's from signals from the Crank sensor .

May 31, 2017 | Lincoln Cars & Trucks

1 Answer

1999 chevy blazer will not start. No spark!?!? No spark from the coil to ground.


Could be a bad coil, bad Ignition Control Module (what controls the ignition coil as commanded by the engine computer), or a bad crank position sensor, or cam position sensor. Or the wiring and circuits to all the ignition parts.
Often it is the crank sensor (CKP sensor)-The pcm must have this information from the crank sensor to determine spark timing. If no good signal from the crank sensor, there will be no spark.

May 29, 2017 | Cars & Trucks

1 Answer

Where is the crank position sensor,the ignition module,and coil pack at on a 1998 Pontiac Montana transport


What size engine . 3.1 or 3.4 Has two crankshaft position sensors
Crankshaft Position (CKP) Sensor (24X)
RH side of engine at end of crankshaf, behind harmonic balencer
Engine Controls Component Views
Engine Controls Connector End Views
Crankshaft Position (CKP) Sensor (7X)
Lower rear of engine
Ignition Control (IC) Module
Top center rear of engine coils are on top of ICM - ignition control module .

Apr 05, 2017 | Pontiac Montana Cars & Trucks

1 Answer

Where is the crankshaft position sensor located on the 2002 Mitsubishi Montero sport xls 3.5 truck.


Hi David, The link below is how to test the crank sensor (1997-2004 3.0l Montero, Hope this helps......CHEERS
http://easyautodiagnostics.com/mitsubishi/3.0L/crankshaft-position-sensor-test-1#3
The crankshaft position (CKP) sensor is located behind the timing belt... but testing it is done without removing the timing belt or its components. This is due to the fact that the crank sensor's connector is located on top of the engine and in plain view (next to the ignition control module). In the photo below, the orange arrow points to the location of the crankshaft position sensor connectors (photo applies to: 3.0L 1997-2004 Montero Sport).

Mar 31, 2016 | Mitsubishi Cars & Trucks

1 Answer

Need to know where the crank shat sensor s located on a 2003 pt crusier


Follow your plug wires to your coil packs. Your coil packs are attached to the ignition module. There will two wires running form ignition module right to the crankshaft position sensor which should be in the engine block

Aug 07, 2010 | 2003 Chrysler PT Cruiser

1 Answer

Cannot figure out how to test the crank shaft position sensor to see if it has caused recent ignition failure because the harness has three leads at the end that connects to the ignition modual and two...


If you unplug the crank sensor at the module and measure the resistance of the crank sensor. (the yellow wire and the black wire) The resistance of the crank sensor should be 900-1200 ohms.

May 17, 2010 | 1989 Pontiac 6000

3 Answers

Im not getting any spark in my 96 Corsica


Ignition module may be bad. It should be located under the coils, the coils usually plug into the ignition module. Also might be a bad crank or cam sensor

Sep 11, 2009 | 1996 Chevrolet Corsica

1 Answer

Location of ignition control module


It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Mar 16, 2009 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5530 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...