Question about Ford E-150

1 Answer

1994 F-150 auto trans issue.

1994 F-150, 5.0 w/"metric" 14 bolt automatic. Always been fine until it sat for a year with only occasional drive around the yard. Now it will not shift out of 2nd gear.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,630 Answers

Change the fluid and see if that corrects the problem, this is an electronically controlled transmission so a code check is also a good idea.

Posted on May 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size are the bell housing bolts on a 1994 suzuki sidekick 1.6 8v auto trans


bell to engine, or bell to trans, some have side braces to trans.
3speed auto or 4 speed, ?
tough question, you lost ALL your bolts. (ouch) the are all metric.
the FSM nor the official Ecat, shows NO size.... (fact)
first off,.if not all lost then the other side there. are same size.
if the left is not missing , you have bolts to match to right.!
correct? take the left bolts to store and buy a match.
and the nuts. there.

there are 4 factors on these bolts. (suzuki still sells them)
1: diameter, most are 8 and 10 mm. measure the hole see that?
2: pitch, (iso spec sizes ) per above.
3: length (this too can be measured,)
4: grade. (id use grade 8.8) we dont have spec, so.... more is better.....
if not using OE parts.(suz)
you get to measure each hole first. (with a dial caliper)
measure inside diameter. or use 3 known bolts to find this out.
the MM diameter. 25.4 x inches = metric,

there are 2 big studs there too.
and finding that nut sizes is not hard. at all.
get diameter with caliper then buy the ISO pitch nut matching that.
there are fine and coarse ISO sizes. just looking answers that.
but if not, buy 2 nuts, that diameter in both fine and coarse.
bingo the nut is found.
as seen here
http://www.fixkick.com/tranny/slush/slide3L30/html/image_1.html


that same dial caliper tool (all shops have one..so.)
the rear measure depth. (basics)
the rear is insert in to a hole on trans to the block side and total depth is known (to rear edge of bell casing)
so buy mm length just less than that.
there is no easy way, only using a tool finds this out.
or use stick pushed in to hole an use thumb nail to mark stick
then measure that with any metric ruler. directly.

or just buy them. (they have no graphics for this level of detail back then so cant see them , must ask)
http://www.suzukicarparts.com/parts/1994/Suzuki/Sidekick/JLX/?siteid=214820&vehicleid=9153&searchText=

you will have to call them and tell them what's missing.
if you had listed all bolts missing i can give out real suz. part numbers. (i have a real hard copy parts list manual)


all this above is standard shop practices... how to measure bolts.

Aug 14, 2015 | 1994 Suzuki Sidekick

2 Answers

What is required to remove the transmisson?


Well......it depends on the application....997 twin turbo 911....or a chevette.....

Apr 02, 2015 | Cars & Trucks

1 Answer

91 continental remove trans


Disconnect battery remove drive shaft, remove starter ,remove mounts undo bolts around bell housing,leave one bolt in so it won,t fall out, remove speedo wires and trans pipes if auto undo bolts to convertor put a floor jack under it and ,then remove the remaining bolt lower Trans down.

Aug 12, 2014 | 1991 Lincoln Continental

1 Answer

Flywheel bolt size


I'm thinking here that the head of the bolts is not very thick in which case the socket you are using will need some modification. If you look in the socket you will see that there is a small lead in relief and this will only allow the socket to full engage on 1/2 of the bolt head. Place the socket in a vice and use a grinder to grind of the face of the socket until the sides are square across. This will give full contact with the bolt head inside the socket.. Another point, it is unusual to find metric bolts in a USA made engine so check out the other size metric sockets as European metric use 9-11-13-15-16-18-20 mm sizes compared to Asian 10-12-14-17-19-21 mm. in auto production.

Apr 22, 2014 | Chevrolet Tracker Cars & Trucks

1 Answer

Size caliper bolts


It will be metric . The trick is Asian metric use spanner sizes 10-12-14-17-19-21mm while European metric use 11-13-15-18-20 and so on Unless you have a full range of spanners the one you want will be the odd size. 5/8 is around 18mm so try that

Mar 03, 2014 | Cars & Trucks

1 Answer

Rear caliper bolt size 2001 jeep grand cherokee laredo


If you mean to remove bolt, they are a metric allen size. To replace, you need a special pin / sleeve type bolt, available in sets at the auto parts store for around $14.

Jun 19, 2011 | 2001 Jeep Grand Cherokee

1 Answer

'99 Beetle cruise control surge and speedometer has slight flutter.Occasionally speedometer drops to zero mph and cruise will then stop working. The "surge" is so bad that you can not drive with cruise on....


I would take a blind guess and sat the speedo sensor has an issue. 99' beetle should have an 01M auto, and the speed sensor is also the dipstick for the final differental drive. search around this area of the trans for the cable and snoop around. loose at the trans ? bad connection somewhere??

Dec 09, 2009 | 1998 Volkswagen Beetle

1 Answer

Issues when changing gears in a automatic 2001 Volkswagen passat. Car kind of jumps or shakes when changing gears from Park to reverse or to drive. But works fine when changing gears into 4, 3, or 2.


it is bcause the trans shifts opposite diection when going from reverse to drive but i would check mounts where they bolt to trans have seen them with broken bolts

Aug 23, 2009 | Volkswagen Passat Cars & Trucks

1 Answer

1992 toyota pickup need to change the cluch. is there a easy way to do this.???


no easy way.you will need a jack and stands metric tools disconeck batery remove starter and drive line remove shifter ther are 6 bolts you can axis them from the inside of truck by removeing the shifter boot.place a jack under the trasmition remove the trasmition mount and then remove the 6 bellhouseing bolts 14.mmbut first disconeckall wires from the tansmition after all this is you may need help to lower the trans.6 12mm bolts hold the cluch inplace remove and replace cluch.repet proses should take 3hrs to do this

Apr 16, 2009 | 1992 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...