Question about 1994 Chevrolet Suburban

Open Question

How/replace brake light switch,1994 chevy-truck 1500?

1994 chevy truck 1500

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

yotaguy
  • 232 Answers

SOURCE: need Rear Brake Diagram for 1994 Chevy K2500 4x4

Here is the diagram,It is always a good idea to only disaasemble one side so you can use the other side as a reference,I also reccomend using a set od brake pliers,they will the disassembly and reassembly much easier.
0900c1528008f6a2.gif

Posted on May 30, 2009

  • 1206 Answers

SOURCE: i replaced the brake light switch on my 1994 chevy

it should be adjustable the switch should touch the pedal arm just enough to make light come on that way the slightest tap on the brakes make lights come on.

Posted on Jan 07, 2010

Testimonial: "Thank You "

motor1258
  • 6674 Answers

SOURCE: how to replace a brake light switch for a 1989

Look up under dash where brake pedal pivots, you should see a switch that is activated by pedal arm.

Posted on Mar 07, 2009

  • 4 Answers

SOURCE: 1994 CHEVY K1500 BRAKE LIGHTS DON'T WORK TOP CAB LIGHT WORKS

I figured out my problem!
From the VERY BEGINING... I changed my brake pedal switch with a BRAND NEW switch, and the lights still didn't work.

Well, I went back down there with a live wire and touched the contacts..and guess what.. the brake lights lit up!

I got a faulty NEW brake pedal switch!! I went a year with this problem, so learn from my issue, test even your new parts if it doesn't fix the problem to completely rule it out!

I hope you guys figure out what's going on with your issue.

Posted on Apr 21, 2009

  • 225 Answers

SOURCE: brake bleeding

if you didn't bleed the lines after putting the master in. then there is a good chance there is air in the lines now. may go through a quart of brake fluid before all the air is out. remember to start at r-rear/ l-rear/ r-front/ l-front last.will take some time. don't forget to adjust the rear brake while your there to help with the pedal

Posted on Aug 13, 2009

Testimonial: "thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My headlights have quit working on my 1994 Chevy 1500 pickup. I replaced the headlight switch but they still don't work. The parking lights come on but not the headlights


Try checking both a; your fuses, and b; check your bulbs. You should have two fuse boxes, one under hood and one in or under the dash. Check those for bad, blown or weak fuses. And check your headlights bulbs for them being good and their connection. If this doesn't fix your problem, you may check out your highbeam switch.

Dec 31, 2011 | Cars & Trucks

1 Answer

I have a 1994v chevy 1500 pick up.all lights work except all brake lights rear and third light are all out


more than likely it the switch on the brake pedal pretty common problem on these trucks

Mar 06, 2011 | 1994 Chevrolet K1500

3 Answers

Both my brake lights dont go on on my 1994 chevy suburban 1500 i have changed both bulbs but still do not work Please HELP!!


First check the fuse and replace if it is blown. If fuse is OK, then it sounds like the brake light switch has failed. It is located on a bracket under the dash near the top of the brake pedal arm. You could put a bridging wire across the terminals to confirm if the switch is out and the rest of the wiring is OK. If the lights then work replace the switch.

To remove switch, disconnect wiring, loosen locknut and unscrew switch. Replacement is reverse procedure. To adjust, screw in switch until operating button is fully depressed by pedal arm, tighten locknut and reconnect wires. Check for correct operation of lights.

Nov 17, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

I have a 94 chevy 1500 and the brake lights are dim and wire from brake switch gets hot brake is on then it blows a fuse. traced all wires and replaced brake switch. what else could it be?


Possibly a short in the directional switch in the steering wheel. Your brake lights use the same filament as the turn signals, so the brake light wiring goes thru the directional switch. Does one wire from the brake light switch go up the steering column?

Sep 16, 2010 | 1994 Chevrolet C1500

1 Answer

I just replaced the chasis on my 94 chevy 1500 series had brake lights before but no rear park lights now all i have is signal lights any thoughts on this


Check ground wire at frame at rear. Brake lightsand hazards don't use this ground so they work if it fails, running lights will not.

Mar 15, 2010 | 1994 Chevrolet K1500

1 Answer

Adjusting or replacing brake light switch on 1994 Chevy S10


i don't think there is a adjustment on it, but there is a clip on the brake pedal to hold the brake switch on.

Feb 19, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

I have 1994 gmc 1500 5.7 brake lights want work replaced brake switch also brake relay control still not working help


next is to check the wiring at the signal light switch,check were the connecter from the switch plugs into the main harness this is located at the lower part of the steering column, its common for the brake light hot wire to heat up there causing a bad connection, ive repaired a few of these, also heres a wiring diagram to help you, hope this is helpful.13bfafc.gif

Feb 13, 2010 | 1994 GMC Sierra

1 Answer

I replaced the brake light switch on my 1994 chevy silverado,but when you press the pedal it won't move the contact enough to make the brake lights come on.


it should be adjustable the switch should touch the pedal arm just enough to make light come on that way the slightest tap on the brakes make lights come on.

Jan 07, 2010 | 1994 Chevrolet C1500

3 Answers

Replace brake switch on 1995 chevy cheyenne 1500


Brake switch wiring good, can manually make switch and brake lights work. But when installed and brake pedal mashed does not work. Slight pressure on rear of switch will allow to work. How do you keep switch stationary? Switch is clamped around booster rod and has clip installed. Switch is new. Is there a brake pedal adjustment? HELP PLEASE.......... 1995 CHEVY 1500, 5.0L ENGINE

Nov 22, 2009 | 1995 Chevrolet C1500

2 Answers

Brake lights


check out the brake light switch located on the brake peddle. Could be out of adjustment or burned out.

Jul 03, 2008 | 1994 Chevrolet K1500

Not finding what you are looking for?
1994 Chevrolet Suburban Logo

Related Topics:

1,739 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...