Question about 1998 Oldsmobile Cutlass

Open Question

How to replace windshield washer reservoir on 1998 cutlass Can it be replaced from underneath or do you need to replace the battery and battery tray to access the reservoir from the top?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: windshield washer reservoir tank is leaking how do I replace?

You must remove from it's mount and empty out any fluids that is in tank.fill the tank with water and locate where the leak is coming from. wash tank a few times and the let dry upside down. Get some sand paper (80  grit course) and sand area where leak is, clean area with a vacume or clean rag.you can buy a 2 stage epoxy that comes in an injection form and squeeze it out on a pc of paper and then get a q-tip and mix the 2 components together, fill the crack or hole generously with the q-tip, if you have to,let dry for 24 hours and mix more and put more on. let dry another 24 hours, replace tank back in it's place and you've solved your leak. (epoxy does wonders if its used properly.
Frankthetank

Posted on Nov 23, 2008

Ad
  • 5 Answers

SOURCE: Windshield washer fluid will not pump

the windshield washer pump might be bad. It should be located somewhere on the reservoir

Posted on Nov 27, 2008

MNfisherman
  • 11896 Answers

SOURCE: windshield washer fluid reservoir - MB ML 350

right where the lines connect to reservoir, has little black seals that leak. I recommend removing reservoir, empty it out, then use RTV silicone and place it between seals and reservoir. Let it dry for FULL day. than reinstall.

Posted on Jun 23, 2009

GasparMacari
  • 166 Answers

SOURCE: Replace 2001 silverado 1500 4x4 windshield washer fluid reservoir

the only solution acording to the manual is to replace the reservoir... not much to say about that, u do have the option to patch it...be careful with the product u use to glue that patch.
take care

Posted on Aug 21, 2009

bschilz
  • 2049 Answers

SOURCE: replace serpentine belt 1998 olds cutlass

Here's a link to a series of videos that will explain how to change the serpentine belt.

http://www.wonderhowto.com/how-to/video/how-to-change-a-serpentine-belt-on-your-car-39904/

Here is a diagram of the belt routing which will help you put the belt back on correctly...
18841fa.jpg

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace 2007 accent washer fluid reservoir


if same as 2004 Accent, then remove right front wheel, slide underneath, and start wrenching. should be 2-3 bolts

Jan 30, 2013 | 2007 Hyundai Accent GS Hatchback

1 Answer

How do you install a new windshield washer pump


the windshield washer motor is at the bottom of the reservoir,you will need to remove the water reservoir, the motor usually pull out of a rubber grommet & goes back in the same way, just make sure that the rubber grommet isn't perished, if it is replace it.......cheers

Jun 21, 2011 | 1998 Oldsmobile Intrigue

1 Answer

Where is the battery located?


underneath the windshield washer reservoir on the driverside front under the hood. ik weird place

Dec 10, 2010 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Where is the location of the battery in a 94' cutlass supreme ls?


Pictures coming next!

CAUTION Always make sure that the ignition is OFF when disconnecting or connecting the battery cables. Failure to do so may cause damage to the computer control module or other electronic components.

  1. Make sure the ignition is OFF . Remove the air cleaner assembly if necessary, and disconnect the negative battery cable, then the positive cable.
  2. Unfasten the retaining bolts, then remove the cross brace.
  3. If equipped with Anti-Lock Brakes (ABS), remove the relay center and bracket, then position aside.
  4. If necessary, detach the electrical connector and hose from the windshield washer pump, then unfasten the reservoir retaining nut and remove the reservoir.
  5. Remove the air cleaner bracket upper attachment bolt.
  6. Unfasten the battery heat shield, hold-down bolt, and retainer.
  7. Remove the battery from the battery tray.
To install:
  1. Place the heat shield on the battery, then position the battery in the vehicle.
  2. Install the retainer, air cleaner bracket and hold-down bolt. Tighten the hold-down bolt to 13 ft. lbs. (18 Nm).
  3. Install the air cleaner bracket upper attachment bolt. Tighten the bolt to 35 inch lbs. (4 Nm).
  4. Position the windshield washer reservoir and secure with the retainers. Attach the hose and electrical connector to the windshield washer pump.
  5. If equipped with ABS, install the relay center bracket and relay center.
  6. Position the cross brace, then secure with the retaining bolts. Tighten the front bolt to 18 ft. lbs. (25 Nm) and the rear bolt to 35 ft. lbs. (47 Nm).
  7. Connect the positive battery cable, then the negative battery cable. Tighten the cable bolts to 11 ft. lbs. (15 Nm).
  8. If removed, install the air cleaner assembly.

Oct 20, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Where is the battery located?


It's directly under the windshield washer tank behind the fender wall. It should be secured down by a strap or a bar. I believe you have to access it through your wheel well by removing the wheel well cover

Oct 06, 2009 | 1995 Buick Regal

1 Answer

How to remove and replace windshield wiper reservor


Here are the steps to remove the reservoir:

  1. Remove the battery and battery tray from the vehicle .
  2. Remove the inner wheel housing from the vehicle.This is the plastic liner.
  3. Disconnect the electrical connector from the washer pump.
  4. Disconnect the electrical connector from the washer solvent level sensor.
  5. Disconnect the washer hose from the washer pump.
  6. Remove the upper bolt from the washer solvent container.
  7. Remove the lower bolts from the washer solvent container.
  8. Remove the washer solvent container from the vehicle.

Sep 03, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Wiper fluid level sensor replacement


Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Jan 15, 2009 | 2000 Mercury Villager

1 Answer

How to get to the batter in the car


As best I remember, you need to remove a metal strut that runs from the left side along the fender to the front body crosspiece. It's two or three bolts. Remove the windshield washer reservoir (plastic), another two bolts. Then you will see the battery tray. Install the battery and holddowns, and connect the cables (side connectors). Replace the windshield washer reservoir and reinstall the strut.

Jan 15, 2009 | 1993 Chevrolet Lumina

2 Answers

Replacing windshield washer pump


I assume you access from underneath. Remove plastic shroud and expose reservoir and pump? right?

Nov 11, 2008 | 2001 Hyundai Elantra

Not finding what you are looking for?
1998 Oldsmobile Cutlass Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...