Question about 1989 Chevrolet Suburban

1 Answer

What motor came stock in a 1989 chevrolet

What motor came stock in a 1989 chevrolet silverodo pickup 1/2 ton four wheel drive. motor block number is 10243878

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 343 Answers

The eighth digit in the VIN number on the trucks dash (view from outside the truck on the drivers side) is the engine code. I believe M is a 350 and P is a 305.

Posted on May 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

14015445 engine number identification


As long as the motor mount line up the engine will swap out ok but you may have to change the ECM for the truck or reprogram the one you have. In addition be sure the tranny will bolt up and the drive shafts are the same length.

Jul 13, 2014 | Chevrolet 1500 Cars & Trucks

1 Answer

1989 chevrolet pickup half ton, what motor is stock.


That year should have been either a 263ci 4.3L V6 for C - series trucks and the 350ci HO 5.7L V8 for K -series trucks.

May 27, 2010 | 1989 Chevrolet K1500

1 Answer

1989 Chevy 1 ton wont start


It is likely the electronic ignition control module. When they go, they just go bad and usually when you are driving.

If it was a smaller vehicle it could also be a timing belt but your's has a heavy duty valve train so no worries there.

Mar 17, 2010 | 1989 Chevrolet C/K 3500

1 Answer

Truck will not go into 4 wheel drive


it sound like it is going in to 4low rang but it may only be low 2wheel power brake it a little on dirt if the tires sin in the rear it was only low ranged 2 wheel u can get this by putting it in 4low and unlocking the hubs it may be a hub prob as it is common

Dec 06, 2009 | 1989 Chevrolet K1500

1 Answer

I have a 1993 chevy 1/2 ton pickup with 5.7 liter and I cant get the four wheel drive to work when i put it into four whell the rear wheels alternate when slipping as they should but nothing from the front...


First of all try checking your fuse box and make sure the 4X4 fuse is still good. If the fuse is good, move the shift lever for the 4X4 on the floor into 4 high, then get a friend to watch underneath when you move the vehicle a little bit to see if the front driveshaft is turning. If the front shaft going to your differential is turning the problem is probably the electric actuator on the differential.

Dec 04, 2009 | 1993 Chevrolet K1500

1 Answer

Chevy 1993 half ton 4 wheel drive


Is your 4x4 light coming on? Does the shifter move smoothly into position? I have a 95 that I have just about had every proplem imaginable. Need morre info. John.

Jan 10, 2009 | 1986 Chevrolet K1500

1 Answer

Remove the front disc rotor


The rotor and hub assembly are held together by the studs,you must first remove the 4-wheel drive hub assembly,then the wheel bearing nuts,and pull the hub and rotor off as a unit. Next lay it(back down) on a piece of wood, using a drift punch drive the studs out. Turn it over ,lay it(face down) on a block of wood, line the new stud splines up with the grooves in the hub and drive them in with the punch and reassemble. A set of dentist style picks will be helpful with the clip in the 4wd hub and a 4 lug 4wd nut wrench will be needed.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?
Cars & Trucks Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...