Question about 1998 Ford Escort

1 Answer

Engin truns over but no fule to engin - 1998 Ford Escort

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,520 Answers

Check your Inertia switch. This is a safety switch that has a reset button you hold for 3 seconds to reconnect the fuelpump. It is meant to stop the fuelpump in a wreck. Sometimes closing the trunk or a door will trip them.

Usually they are mounted in the trunk area of the car or inside the kickpanels up front.

Posted on May 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can i do if the emergency cut off switch is not working and the engin wants to turn over but cant fully engage


If you have checked the voltage at the inertia switch and the switch can not be reset, you would need to replace it.

Oct 05, 2012 | 1999 Ford Crown Victoria

1 Answer

Car suddenly died. checked battery, i think it's the fuel filter. I have no idea where it is located.


The fule filter is located in the engin compartment. Remove the air filter, and the compartment that houses it. Looking towards the fire-wall, and slightly down. The fule filter is located in the lower left. I suggest you purchase the fule filter first and this will help you find it.
Use A LINE WRENCH too remove the bottom gas line. The top bolt can be removed with a scocked( all of these are Metric) The bottom one is a ******!!!

Goo lunk

Jun 28, 2011 | 1994 Mitsubishi Expo

1 Answer

Engin light is on and it fells like a fule problem


read the codes and they will tell you what is wrong. They are available all over the internet. Just google "dodge codes"

Jul 08, 2010 | 2004 Dodge Ram 3500 Truck

1 Answer

The engin get warm and then the heater come on than it trun to cool and will not get hot


One or more of:

1. Your coolant level is low
2. Your thermostat doesn't close and needs to be replaced
3. The valve from the cooling system to the heater core is stuck
4. Your heater core is clogged

Dec 17, 2009 | 2001 Dodge Durango

1 Answer

Wont idel when warmed up


seems to me there may be a problem with the transmission, because you say it runs fine in neutral and dies when you put it in gear!!!
only logical thing if everything else you mentioned has been ruled out!!!

Jun 18, 2009 | 1995 Dodge Dakota

1 Answer

My car engin dose not start,it is 1993 nissan bluebird ARX?


This def sounds like a fule pump issue ...it should be located in the gas tank its self although i would check the fuses first before getting into the tank.
If this is in a 240sx the way into the tank is through the trunk.Lift the carpet and you will see on the mid right side a small 6-8" lid with some wires going into it. Unscrew that and your on your way in.
If you do pull out the pump just be careful handling it as to not break the sensor unit attached to the pump.

Jun 17, 2009 | 1992 Nissan 240SX Fastback

1 Answer

My car engin dose not start?


make sure there is fule getting to the injection unit by pulling the fuel line off, if there is no fuel in the line then check the fuel filter has no broken in side!

Jun 17, 2009 | 1992 Nissan 240SX Fastback

1 Answer

Looking for standard computer chip for minivan


try a used one out of a junk yard.thats not a comen part to go bad on the caravan. if your van run i would a second oppion on it .because most of the time van will run for a log time with engin light on.usely its a 02 senser that will trun the engin light on . good luck

Apr 19, 2009 | 2002 Dodge Grand Caravan

1 Answer

Timin


a1989vert: With the engine off, remove the SPOUT connector jumper. It lies just under the distributor and is rectangle shaped.
Connect timing light to #1 spark plug wire (Front passenger side)
Timing should be at 10BTDC. If not correct then loosen distributor bolt and adjust. When done, trun engin off, tighten dist. bolt and plug SPOUT jumper back in.

Brian

Jul 19, 2008 | 1994 Ford Mustang

Not finding what you are looking for?
1998 Ford Escort Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...