Question about 2006 Bentley Drophead

Open Question

Need to see a diagram on the color coded air lines for foot valve on international truck model no(f-9370) 1987

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Full brake air pressure on Daf CF but gauges read zero,buzzer remains 'on'and dash reads 'low brake air pressure' and ABS fault.-- fitted sensor unit at air dryer but no change. Help would be great


check the air pressure switch at the tank supply line at the foot ( treadle ) valve if that switch is not operational then it may be where the system is not getting a full pressure report
you should have a pressure reading on the air gauges in the dash as they read from the air tanks
remove the compressor line to the tank and check for air flow from the compressor when running as some european built trucks have the steel line as n air cooling line and they tend to carbon up internally and block air flow( scania in particular uses a pipe shaped as a coil that was very bad in design

Jun 12, 2017 | DAF Cars & Trucks

1 Answer

Where is the egr valve on a citizen c5


  • First you want to open up the hood of your car
  • Find the engine diagram sticker on the inside of the open hood and identify the mechanism that is labeled "EGR Solenoid" on the sticker.
  • Find the "vacuum line" on the sticker diagram and identify its color. This is the line that runs from the EGR solenoid to the EGR valve.
  • Locate the vacuum line inside the engine compartment of the vehicle toward the front of the driver's side. The vacuum line will be the same color on the vehicle as it is on the diagram.
  • Follow the vacuum line from the front of the vehicle where it connects to the EGR solenoid through the conduit that carries it to the EGR valve at the rear of the engine compartment. The easiest way is to track the uniquely colored vacuum line along the path between its two connection points. The vacuum line connects to the EGR valve, which is the disk-shaped object located at the rear of the engine compartment
    on the driver's side.

May 04, 2016 | Cars & Trucks

1 Answer

Where is the low air pressure switch located on 97 Kenworth dump truck.


low pressure switches can be mounted at the air tanks ,on the line from the compressor to the tank next to the tank or at the foot valve air pressure line in to the foot valve.

Feb 14, 2015 | Cars & Trucks

1 Answer

Wiring diagram international 4300


the brake light switch will be in the side or base of the foot valve . It is air operated and activates when the foot brakes are applied . It should be about 1 1/4 " in diameter with 2 wires to it

May 06, 2014 | Cars & Trucks

1 Answer

Getting a code for smog pump


better check that info again. inspect belt routing diagram and vacuum diagram for thermactor pump and thermactor air system parts being present on your calibration. to my recollection there was no thermactor air used. where would they put all that plumbing?
pump, diverter valve, exhaust check valves, upstream and downstream air tubes? a ford has a label on the radiator support depicting the usage, hose color, and general vicinity in a schematic for ford technicians to identify. there is also a belt routing diagram that depicts the pulleys for the components. you dont have one...right?
you may have a code glossary for older vehicles. get the right manual at the library for free and restart diagnosis. or goto the emissions authorized repair facility and get the question answered after a quick self test

Apr 20, 2014 | 2002 Ford Taurus

1 Answer

Need to wireing diagram for iat sensor


Vehicles: all computer-controlled internal compustions engines equipped with an IAT (Intake Air Temperature) sensor

Intake Air Temperature (IAT) Sensor

Operation - IAT

This sensor is a resistor based sensor which detects the intake air temperature. According to the intake air temperature reading the ECM/PCM will control the necessary amount of fuel injection.

ECM = Engine Control Module (aka "the car's computer")
PCM = Powertrain Control Module (aka "the car's computer")

Dec 04, 2011 | Cars & Trucks

1 Answer

I need a vacuum line diagram fo a 1996 Chevy Lumina, 3.1. One line that is not connected to anything, is located at the top of the engine.


Sorry I don't have the diagram, but I do have a diagram of the engine and component locations. Your vacuum system is fairly simple. You have a MAP sensor attached to the air cleaner. I have pasted a picture below. It has one electrical connector and one vacuum hose that goes to the intake manifold or the throttle body.
Behind the right headlight is your evap canister. This will have a hose or line running to the fuel tank. Then it will have another hose going to the purge valve. The purge valve should be close by and it has a connector plus another hose that goes to the intake manifold.
Then you have the PCV hose that goes from the PCV valve in the valve cover to the air cleaner or intake manifold. I think yours just has a hose from the air cleaner and the rest is internal.
There is one more vacuum hose, and that is the bog one that goes from the intake manifold (or throttle body--looks to me like there are a couple of vacuum ports on the back side of the throttle body, and there may be a "T" on one of the hoses) to the brake booster. It this one was off, the engine would not run, as the vacuum draw is large. Please let me know if you cannot figure it out from these instructions and provide a picture, if you can.

MAP sensor:
jturcotte_653.jpg

purge valve:
jturcotte_654.jpg

jturcotte_2455.gif
jturcotte_2456.gif

Oct 30, 2011 | 1996 Chevrolet Lumina Mini

1 Answer

Have engine codes P1411 and P0411 secondary air injection system malfunction and catlyst not ready problem, car drives fine, but no pass smog, any help would be appreciated, need emission diagram if...


CHECK SECONDARY AIR PUMP SOLENOID FUSE AND VACUUM LINE TO SOLENOID.IF FUSE AND VACUUM LINE OKAY GETTING VACUUM. THE SECONDARY AIR PUMP SOLENOID OPEN OR SECONDARY AIR PUMP FAULTY.ALSO CHECK CHECK VALVES AND THE AIR LINES GOING TO EXHAUST MANIFOLD. MAKE THEY ARE NOT DAMAGED OR LOOSE.THE CHECK VALVES ON THE LINES IS ONE WAY VALVES YOU SHOULD NOT BE ABLE TO BLOW BACK INTO VALVE IF SO ITS FAULTY.

Jul 07, 2010 | 2001 Porsche Boxster

1 Answer

Need a air brake diagram for a Ford L7000


96 F & B Series

Air Brake System, FT Series


b4c4ba6.gif
Item Part Number Description 1 2025 Front Brake Chamber 2 2A095 Quick Release Valve 3 2075 Compressor 4 2085 Governor 5 2A783 Tank Valve 6 2A550 Safety Valve 7 2063 Air Tank Reservoir 8 2A567 Drain **** 9 2B170 Single Check Valve 10 2K119 Double Check Valve 11 18737 Low Pressure Indicator 12 2A270 Foot Control Valve (E-7) 13 13480 Stoplamp Switch 14 2A662 Parking Brake Control Valve (PP-1) 15 2B280 Chassis Bulkhead Manifold 16 2B431 Inverting Relay Valve (R-7) 17 2A449 Relay Valve (R-12) 18 2225 Rear Brake Chamber A — 3/8-Inch Hose B — 1/4-Inch Hose C — 1/2-Inch Hose D — 5/8-Inch Hose

May 04, 2009 | Ford F Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bentley Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Are you a Bentley Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...