Question about 1990 Geo Storm

1 Answer

What kind of tools do i need to take off the passanger door

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 973 Answers

You would need assorted set of screwdrivers or Torx bits and a door pane popper to remove the plastic clips,

Posted on May 27, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Passanger window wont roll up from driver side or passanger side

Replace the regulator. It comes with the motor. You have to remove the door panel to access it.

May 26, 2015 | 2006 Kia Sorento

1 Answer

1998 lincoln towncar rear passanger door will not close

Not enough information for an exact diagnosis so check the following: If the door is sagging so the latch won't grab the post on the body, that post is adjustable. You'll need a special socket to do that. Autozone lends tools. If the door latch is out of sync....latch is closed while the door is open then open the door using the outside handle. That will open the latch so it will function correctly. If neither of these suggestions address the problem then be a little more specific in describing your problem so we can be better prepared to help.

Jul 04, 2014 | Cars & Trucks

1 Answer

1998 passanger front door and tail gate will not unlock or open

for this problem, I think you need to see a car body shop.


Nov 09, 2013 | 1998 Land Rover Range Rover

1 Answer

My passenger door sensor is not working right. It shows that the door is open when it is not. I did not think it was a big deal until the other night we were driving and the interior lights started to...

I'm not sure which passanger door you're taking about, but i'll assume it's the front passanger door. What I think is happening is that the passanger door's not pushing the Door Switch all the way down when it's close cause the light to stay on.

First check to see if the door switch(to see the switch, open passanger door and it located lower left coner. see picture below) is work by push on. The interior light should go out when push down and on when release.
k42282_35.jpg -If switch is not working, replace door switch.
-if switch is working, adjust passanger door inward by loosing the door striker(A) bolts(B) and tipping it with a hammer. Adjust until door open/close proplery and light stay off when door is close.


Jan 19, 2011 | 2004 Honda Odyssey

1 Answer

Passanger window not working

the wires in the rubber boot or the push in connection ,its connects the door to the car body

Apr 19, 2010 | 2003 Hyundai Santa Fe

1 Answer


do the door handles broken? is the lock mechanism broken....if so you can buy a tool for a parts house that you can slide thown the window to unlock it and work the door might have luck with a clothes hanger to reach the handle mechanisim....I would not drill out the rivets in the handle.....hope this helps...

Mar 11, 2010 | 1998 Ford F150 Regular Cab

1 Answer

Ac works on passanger side but not on driver side. and its not the control board cause we checked it its fine. both sides blow out air but the passanger side is cold and the driver side is not?

air blend doors need to be calibrated. they loose calibration after awhile. Since either side can be colder or hotter they loose there sync. it requires the use of a tech 2 scan tool. this might need to be brought to the dealer i you don't know anyone in the industry with one. That is the dealer specific scanner, most shops don't have them, although my shop does.

Aug 29, 2009 | 2002 Pontiac Grand Prix

1 Answer

Doors not locking

had a similar problem. remote would not work doors and inside switch would not work on passsanger side. There is a part below the passanger side door window and lock switch called the PDM or passanger door module.capable of some really strange behavior as it basically is a mini computer and rf signal receiver. May try reprograming your remotes first, if that doesn't work get new PDM. need to give VIN to parts folk to get it. Think it was about 200.00. Need to remove passanger side door panel and then take apart armrest with door swithes. Kind of tricky. funky screw on the front which has to be loosened and door panel must be off to get to it. anyway after install reprogram the remotes to the PDM. It involves off on, off,on ignition while holding down the unlock door switch, then hold the unlock on the remote?????? the sequence in on the net just search it out for your year.

Jun 09, 2009 | 2003 Cadillac Escalade Esv

1 Answer

Window won't go all down and door won't unlock

Stop by an auto parts store and buy an inexpensive door panel remover tool. It will have simple instructions on the back of the pkg to tell you how to use it.

May 23, 2009 | 1995 Toyota Camry

1 Answer

Door panels

You will need some type of flat tool to start this. The door panels are held on by clips inside and they need to be popped out, but this can be tricky to not damage the panel in the process. There are special Trim & upholstery tools that are flat kinda wedge shapes that are plastic for prying these up and they are fairly cheap (can pick some up for about $6 at places like Harbor Freight) or what I commonly did before buying those tools is wrap a wide flathead screwdriver with a rag and push underneath panel and then pry up to pop up that first one, then you can get your fingers underneath it to pull around edges until you get them all. As soon as you get all the clips off you will need to disconnect the window/lock electrical connectors to completely remove the door panel.

Aug 16, 2008 | 2003 Chevrolet Venture Passanger

Not finding what you are looking for?
1990 Geo Storm Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides