Question about 1998 Chevrolet Camaro

1 Answer

How to change a head gasket in a v8 350 5.7 liter tuned port injected motor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Don't attempt it without a manual with specs, you will need special tools like a torque wrench and an angle meter, you will have to get the head measured and probably resurfaced, also do it in a clean enviroment, and make sure all is spotless during reassembly, even a fingerprint on mating surfaces can cause premature failure of gaskets

Posted on May 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i install a multi port fuel injection tune up kit in my 1991 ford ranger 3 liter v6 motor?


the only fuel injection tune up kit I have ever installed is new injectors and o rings

Nov 12, 2015 | Ford Cars & Trucks

1 Answer

Just re done top of motor. Everything together and I start it steam dumps out of the exhaust. I believe a water hose is wrong from the radiator somewhere. Need to know how to run the hoses. 89 iroc camaro...


Steam from the exhaust means, unfortunately, that coolant is entering the cylinders, and very little running like that will destroy the rings and pistons. It could be anything from an intake or head gasket leak to a cracked cylinder.

Aug 08, 2011 | 1989 Chevrolet Camaro

1 Answer

We replaced the theromostat and the radiator but it is still leaking under the car on the drivers side


Leaking water on teh drivers side indicates a cracked block or cracked head in most cases. Unless you have a water injected motor, I don't remember Ford using one, there are no water ports on that side of the motor. It could be the water pump leaking and being pushed back when the vehicle is running so check for leaks around the water pump. You need to check the heads, side of the engine block and the freeze plugs to make sure there are no cracks or leaks around the head gasket seal.

Jul 06, 2011 | 2000 Lincoln LS

1 Answer

Blown head gasket


This is a major overhaul requiring special tools and expertise.

May 27, 2010 | 1989 Chevrolet Camaro

1 Answer

My email address is: samlivenston1@ nc.rr.com\


The intake gasket gives trouble on this model. The gasket gets weak and usually lets coolant come out on top of the engine between the rear head and the intake. It will run down the rear of the motor onto the transmission. Fairly large job around 6 hours.

Feb 22, 2010 | 1993 Pontiac Bonneville

2 Answers

Chevy truck with water in the oil, already did the head gasket.


did you check the water ports on the head were they opened up with corrosion ,-- did you put the gasket on the right way round ,was it the right gasket with the right number of holes

Nov 21, 2009 | 1999 Chevrolet C1500

1 Answer

Injection pump trouble


This all sounds like it is a blown head gasket, I would not worry about the top cover and the speed control, until you get the head gasket fixed. The head gasket not being replaced will mean a new motor

Apr 29, 2009 | Volkswagen Rabbit Cars & Trucks

1 Answer

F150 5.4 liter v8 running rough, white smoke being exhausted on startup


White smoke while running usually indicates water in the combustion chamber (bad head gasket or cracked head) but white smoke on startup only is usually a sign of unburnt fuel (rich mixture). Either bad injectors, injector seals? Maybe something else That's assuming it's fuel injected

Aug 12, 2008 | 2000 Ford Focus

1 Answer

Car had blown head gasket, sat for about 2 years. Fixed head issue now has run issue. Changed fuel but it runs ok for a few minutes then either sputters or dies just like the key had been turned off. I...


Is it fuel injected? Or carburated?
If it has a carb, did you clean out the float bowels and jets?
If it's injected, you may need to clean or replace the injector nozzles.
Fuel that has been sitting for 2 years can turn to varnish.

And after you replaced the head gaskets, did you do a compression check on the motor?

Jul 28, 2008 | Ford Thunderbird Cars & Trucks

1 Answer

1986 ford ranger xlt 2.9 liter fuel injected


thermostat or blocked matrix in rad,evan head gaskets could be on the way out

Jul 18, 2008 | 1986 Ford Ranger 2WD

Not finding what you are looking for?
1998 Chevrolet Camaro Logo

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...