Question about 1986 Mercury Grand Marquis

1 Answer

How much is a drive shaft for a 86 marquis

How much is a drive shaft for a 86 marquis

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mercury Master
  • 6,927 Answers

About 43.50 exchange at the napa auto parts store.

Posted on May 27, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear end vibrations on a 2000 grand marquis

What has been done so far?

Did you go on a road test --you driving
& a mechanic along for a ride & then switch

Do that

Tire Weights fall off
Drive Shaft Joints bad or shaft installed wrong
Rear Shocks worn out
Loose/Worn Bearings
Bad Tire

Speed at the time of vibration on & off gas
tells you something

Nov 30, 2012 | 2000 Mercury Grand Marquis

1 Answer

Oil pump shaft broke off. How can a person remove broken tip up inside motor?

The oil pump shaft is driven by the distributor. If a broken piece of the oil pump shaft is still lodged in the distributor drive socket you may have to remove the distributor to remove the broken piece. Normally there is no retainer keeping the shaft inserted into the distributor drive socket. So when the oil pump is removed the shaft will typically slide, or fall out.

Feb 23, 2011 | 1991 Mercury Grand Marquis

1 Answer

I have 2000 grand marquis and the rearend shaft that connects to driveshaft is very loose, making a terrible roaring. How do i remove this shaft to replace it?

When you take off the drive shaft, I believe you will reveal the large nut that hold the tail piece on. It has a cotter pin. Remove the nut, and it will slide right out. Then you need a special puller that has fingers that press out ward, hook the bushing, and then extract it. But this could also be an actual bearing I suppose. After tapping the new one in, put in a new seal, and top up the gear oil that you lost when the old seal went out.

Jun 02, 2010 | 2000 Mercury Grand Marquis

1 Answer

Replaceing the front seal in transmission

You will have to remove the transmission.that would include removing drive shaft ,possibly exhaust.

Apr 07, 2010 | 1992 Mercury Grand Marquis

1 Answer

Power window motor broke 86 marqui cant get window up?

You'll have to take the door panel off and raise the window manually.

May 03, 2009 | 1986 Mercury Marquis

1 Answer

Transmission leak


No clamp, it sounds like it is just a bad seal.
Just remove the drive shaft and pry out the old one and tap in a new one. very easy on those cars. juts make sure you put some tran fluid on the rubber part of the seal before installing the drive shaft or it can tear it.

Mar 31, 2009 | 1988 Mercury Grand Marquis

1 Answer

86 blazer front wheel barrings how to ??

Hi there. If by gears you mean the splines on the end of the half shaft, you need to seperate the lower ball joint, if not done already, put the splines in the hub first and then hook the new bearing hub up to the lower control(ball joint) with the shaft already in place.

Mar 02, 2009 | 1986 Chevrolet S-10 Blazer

1 Answer

I have a 86 Mercury Marquis that I am working on helping someone out and I would like to know how the ignition module is won't start.....i have replaced battery, ignition coil, cap and...

if the module is on the side of the distributer it takes a wrench made just for ford modules to remove 2 screws, if you need to replace the pickup in the dist. you have to remove the dist. out of the engine pull the gear off and pull the shaft out of the dist.

Jan 24, 2009 | 1986 Mercury Marquis

1 Answer

2000 Mercury Grand Marquis

I was given an solution by emissionwiz from the fixya site.


Nov 30, 2008 | 2000 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

78289 Answers


Level 3 Expert

5655 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides